#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC8560 1 /* MPC8560 specific */
+#define CONFIG_CPM2 1 /* has CPM2 */
#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#undef CONFIG_TSEC_ENET /* tsec ethernet support */
#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#define CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
/*
* sysclk for MPC85xx
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8560@0"
+#define OF_SOC "soc8560@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8560@e0000000/serial@4500"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/* RapidIO MMU */
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
+#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-#define CONFIG_ETHPRIME "MOTO ENET0"
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
+#define CONFIG_HAS_ETH2
#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#endif