#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_DISPLAY_BOARDINFO
-
-#ifdef CONFIG_36BIT
-#define CONFIG_PHYS_64BIT
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC8548 1 /* MPC8548 specific */
-#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xfff80000
-#endif
-
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1 /* SRIO port 1 */
-#define CONFIG_PCI /* enable any pci type devices */
#define CONFIG_PCI1 /* PCI controller 1 */
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#undef CONFIG_PCI2
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_FSL_VIA
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#endif
#if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
/* Options are: eTSEC[0-3] */
#define CONFIG_ETHPRIME "eTSEC0"
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_FLASH 1
#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
#define CONFIG_ENV_ADDR 0xfff80000
#else
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
-#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
/*
* For booting Linux, the board info and command line data
#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
-
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:ecc=off\0" \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=ramdisk.uboot\0" \
- "fdtaddr=c00000\0" \
+ "fdtaddr=1e00000\0" \
"fdtfile=mpc8548cds.dtb\0"
#define CONFIG_NFSBOOTCOMMAND \