Added initial eNET board support

[oweals/u-boot.git] / include / configs / MPC8544DS.h

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index fb4d172687b00a47c22e556f1c18cfa9c2ebf193..9b1b34cc8bc09635d8b5c20c7a32eabba8aac73a 100644 (file)
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -41,6 +41,7 @@
 #define CONFIG_PCIE3           1       /* PCIE controler 3 (ULI bridge) */
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_FSL_PCIE_RESET  1       /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 
 #define CONFIG_FSL_LAW         1       /* Use common FSL init code */
 
@@ -65,7 +66,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_L2_CACHE                        /* toggle L2 cache */
 #define CONFIG_BTB                     /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING          /* toggle addr streaming */
 
 /*
  * Only possible on E500 Version 2 or newer cores.
@@ -96,7 +96,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 
-#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER      /* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE  0xDeadBeef
 
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000
@@ -202,10 +202,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VSPEED2_TSEC3SER 0x1
 #define PIXIS_VCFGEN1_TSEC1SER 0x20
 #define PIXIS_VCFGEN1_TSEC3SER 0x40
+#define PIXIS_VSPEED2_MASK     (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER)
+#define PIXIS_VCFGEN1_MASK     (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER)
 
 
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CONFIG_SYS_INIT_RAM_LOCK      1
 #define CONFIG_SYS_INIT_RAM_ADDR      0xf4010000      /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_END       0x00004000      /* End of used area in RAM */
@@ -273,11 +273,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_PCI1_IO_PHYS        0xe1000000
 #define CONFIG_SYS_PCI1_IO_SIZE        0x00010000      /* 64k */
 
-/* PCI view of System Memory */
-#define CONFIG_SYS_PCI_MEMORY_BUS      0x00000000
-#define CONFIG_SYS_PCI_MEMORY_PHYS     0x00000000
-#define CONFIG_SYS_PCI_MEMORY_SIZE     0x80000000
-
 /* controller 2, Slot 1, tgtid 1, Base address 9000 */
 #define CONFIG_SYS_PCIE2_MEM_BASE      0x80000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS      CONFIG_SYS_PCIE2_MEM_BASE
@@ -374,6 +369,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_TSEC3   1
 #define CONFIG_TSEC3_NAME      "eTSEC3"
 
+#define CONFIG_PIXIS_SGMII_CMD
 #define CONFIG_FSL_SGMII_RISER 1
 #define SGMII_RISER_PHY_OFFSET 0x1c
 
@@ -424,6 +420,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_SETEXPR
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI