#define CONFIG_MPC8536DS 1
#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */
+#define CONFIG_SPI_FLASH 1 /* Has SPI Flash */
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCI1 1 /* Enable PCI controller 1 */
#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
#define CONFIG_SYS_L2_SIZE (512 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
-#endif
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR 0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#if defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
/* DDR Setup */
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_HWCONFIG /* enable hwconfig */
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_BUS_NUM 1
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#if defined(CONFIG_SPI_FLASH)
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+#endif
+
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
#if defined(CONFIG_PCI)
-#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/*PCIE video card used*/
#if defined(CONFIG_TSEC_ENET)
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_TSEC1 1
#if defined(CONFIG_SYS_RAMBOOT)
#if defined(CONFIG_RAMBOOT_NAND)
- #define CONFIG_ENV_IS_IN_NAND 1
- #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
- #define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
+#elif defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0xF0000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_RAMBOOT_SDCARD)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#else
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
+#endif
+
+/*
+ * USB
+ */
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#endif
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
/*
* For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_IPADDR 192.168.1.254
#define CONFIG_HOSTNAME unknown
-#define CONFIG_ROOTPATH /opt/nfsroot
-#define CONFIG_BOOTFILE uImage
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_SERVERIP 192.168.1.1
"fdtaddr=c00000\0" \
"fdtfile=8536ds/mpc8536ds.dtb\0" \
"bdev=sda3\0" \
- "usb_phy_type=ulpi\0"
+ "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
projects / oweals / u-boot.git / blobdiff