/*
* Hardware Reset Configuration Word
*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_SVCOD_DIV_2 |\
HRCWL_CORE_TO_CSB_2X1)
#ifdef CONFIG_PCISLAVE
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_AGENT |\
HRCWH_PCI1_ARBITER_DISABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_BIG_ENDIAN |\
HRCWH_LDP_CLEAR)
#else
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_LDP_CLEAR)
#endif
-/* System performance - define the value i.e. CFG_XXX
+/* System performance - define the value i.e. CONFIG_SYS_XXX
*/
/* Arbiter Configuration Register */
-#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
/* System Priority Control Regsiter */
-#define CFG_SPCR_TSECEP 3 /* eTSEC1&2 emergency priority (0-3) */
+#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC1&2 emergency priority (0-3) */
/* System Clock Configuration Register */
-#define CFG_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */
-#define CFG_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */
-#define CFG_SCCR_SATACM SCCR_SATACM_1 /* SATA1-4 clock mode (0-3) */
+#define CONFIG_SYS_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */
+#define CONFIG_SYS_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */
+#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */
/*
* System IO Config
*/
-#define CFG_SICRH 0x08200000
-#define CFG_SICRL 0x00000000
+#define CONFIG_SYS_SICRH 0x08200000
+#define CONFIG_SYS_SICRL 0x00000000
/*
* Output Buffer Impedance
*/
-#define CFG_OBIR 0x30100000
+#define CONFIG_SYS_OBIR 0x30100000
/*
* IMMR new address
*/
-#define CFG_IMMR 0xE0000000
+#define CONFIG_SYS_IMMR 0xE0000000
/*
* Device configurations
/*
* DDR Setup
*/
-#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDR_SDRAM_CLK_CNTL 0x03000000
-#define CFG_83XX_DDR_USES_CS0
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x03000000
+#define CONFIG_SYS_83XX_DDR_USES_CS0
-#define CFG_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN)
+#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN)
#undef CONFIG_DDR_ECC /* support DDR ECC function */
#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
/*
* Manually set up DDR parameters
*/
-#define CFG_DDR_SIZE 256 /* MB */
-#define CFG_DDR_CS0_BNDS 0x0000000f
-#define CFG_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ODT_WR_ACS \
+#define CONFIG_SYS_DDR_SIZE 256 /* MB */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ODT_WR_ACS \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
-#define CFG_DDR_TIMING_3 0x00000000
-#define CFG_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
| (0 << TIMING_CFG0_WRT_SHIFT) \
| (0 << TIMING_CFG0_RRT_SHIFT) \
| (0 << TIMING_CFG0_WWT_SHIFT) \
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
/* 0x00220802 */
/* 0x00260802 */ /* DDR400 */
-#define CFG_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
+#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
| (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
| (3 << TIMING_CFG1_ACTTORW_SHIFT) \
| (7 << TIMING_CFG1_CASLAT_SHIFT) \
| (2 << TIMING_CFG1_WRTORD_SHIFT))
/* 0x3935d322 */
/* 0x3937d322 */
-#define CFG_DDR_TIMING_2 0x02984cc8
+#define CONFIG_SYS_DDR_TIMING_2 0x02984cc8
-#define CFG_DDR_INTERVAL ((1545 << SDRAM_INTERVAL_REFINT_SHIFT) \
+#define CONFIG_SYS_DDR_INTERVAL ((1545 << SDRAM_INTERVAL_REFINT_SHIFT) \
| (256 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x06090100 */
#if defined(CONFIG_DDR_2T_TIMING)
-#define CFG_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
| 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
| SDRAM_CFG_2T_EN \
| SDRAM_CFG_DBW_32)
#else
-#define CFG_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
| 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT)
/* 0x43000000 */
#endif
-#define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
-#define CFG_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
| (0x0442 << SDRAM_MODE_SD_SHIFT))
/* 0x04400442 */ /* DDR400 */
-#define CFG_DDR_MODE2 0x00000000;
+#define CONFIG_SYS_DDR_MODE2 0x00000000
/*
* Memory test
*/
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00040000 /* memtest region */
-#define CFG_MEMTEST_END 0x0ef70010
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x0ef70010
/*
* The reserved memory
*/
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CONFIG_SYS_RAMBOOT
#endif
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
-#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
-#define CFG_LBC_LBCR 0x00000000
+#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
* FLASH on the Local Bus
*/
-#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CFG_FLASH_SIZE 8 /* max FLASH size is 32M */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */
-#define CFG_FLASH_EMPTY_INFO /* display empty sectors */
-#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
-#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
-#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */
-#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
BR_V) /* valid */
-#define CFG_OR0_PRELIM (0xFF800000 /* 8 MByte */ \
+#define CONFIG_SYS_OR0_PRELIM (0xFF800000 /* 8 MByte */ \
| OR_GPCM_XACS \
| OR_GPCM_SCY_9 \
| OR_GPCM_EHTR \
| OR_GPCM_EAD)
/* 0xFF806FF7 TODO SLOW 8 MB flash size */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/*
* NAND Flash on the Local Bus
*/
-#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */
-#define CFG_BR1_PRELIM (CFG_NAND_BASE | \
+#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | \
(2 << BR_DECC_SHIFT) | /* Use HW ECC */ \
BR_PS_8 | /* Port Size = 8 bit */ \
BR_MS_FCM | /* MSEL = FCM */ \
BR_V) /* valid */
-#define CFG_OR1_PRELIM (0xFFFF8000 | /* length 32K */ \
+#define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 | /* length 32K */ \
OR_FCM_CSCT | \
OR_FCM_CST | \
OR_FCM_CHT | \
OR_FCM_SCY_1 | \
OR_FCM_TRLX | \
OR_FCM_EHTR)
-#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
-#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
/* Vitesse 7385 */
-#define CFG_VSC7385_BASE 0xF0000000
+#define CONFIG_SYS_VSC7385_BASE 0xF0000000
#ifdef CONFIG_VSC7385_ENET
-#define CFG_BR2_PRELIM 0xf0000801 /* Base address */
-#define CFG_OR2_PRELIM 0xfffe09ff /* 128K bytes*/
-#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE /* Access Base */
-#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access Size 128K */
+#define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* Base address */
+#define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* 128K bytes*/
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE /* Access Base */
+#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* Access Size 128K */
#endif
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
/* SERDES */
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES2 0xe3100
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* Pass open firmware flat tree */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_FSL_I2C
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
-#define CFG_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* Config on-board RTC
*/
#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/*
* General PCI
* Addresses are mapped 1-1.
*/
-#define CFG_PCI_MEM_BASE 0x80000000
-#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE
-#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI_MMIO_BASE 0x90000000
-#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE
-#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */
-#define CFG_PCI_IO_BASE 0xE0300000
-#define CFG_PCI_IO_PHYS 0xE0300000
-#define CFG_PCI_IO_SIZE 0x100000 /* 1M */
-
-#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE
-#define CFG_PCI_SLV_MEM_BUS 0x00000000
-#define CFG_PCI_SLV_MEM_SIZE 0x80000000
+#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
+#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
+#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
+#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
+
+#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
+#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
#ifdef CONFIG_PCI
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
/*
#ifdef CONFIG_TSEC1
#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
-#define CFG_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 2
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#ifdef CONFIG_TSEC2
#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME "TSEC1"
-#define CFG_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define TSEC2_PHY_ADDR 0x1c
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_PHYIDX 0
#endif
+/*
+ * SATA
+ */
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1_OFFSET 0x18000
+#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2_OFFSET 0x19000
+#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+
+#ifdef CONFIG_FSL_SATA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
/*
* Environment
*/
-#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE+CFG_MONITOR_LEN)
- #define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */
- #define CFG_ENV_SIZE 0x4000
+#ifndef CONFIG_SYS_RAMBOOT
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN)
+ #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */
+ #define CONFIG_ENV_SIZE 0x4000
#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE-0x1000)
- #define CFG_ENV_SIZE 0x2000
+ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
#define CONFIG_CMD_PCI
#endif
-#if defined(CFG_RAMBOOT)
-#undef CONFIG_CMD_ENV
+#if defined(CONFIG_SYS_RAMBOOT)
+#undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_LOADS
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
-#define CFG_HID2 HID2_HBE
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
*/
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
/* DDR: cache cacheable */
-#define CFG_SDRAM_LOWER CFG_SDRAM_BASE
-#define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000)
+#define CONFIG_SYS_SDRAM_LOWER CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_SDRAM_UPPER (CONFIG_SYS_SDRAM_BASE + 0x10000000)
-#define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT0L CFG_IBAT0L
-#define CFG_DBAT0U CFG_IBAT0U
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT1L CFG_IBAT1L
-#define CFG_DBAT1U CFG_IBAT1U
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
-#define CFG_DBAT2L CFG_IBAT2L
-#define CFG_DBAT2U CFG_IBAT2U
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* L2 Switch: cache-inhibit and guarded */
-#define CFG_IBAT3L (CFG_VSC7385_BASE | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_VSC7385_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT3U (CFG_VSC7385_BASE | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_DBAT3L CFG_IBAT3L
-#define CFG_DBAT3U CFG_IBAT3U
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_VSC7385_BASE | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U CFG_IBAT4U
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* Stack in dcache: cacheable, no memory coherence */
-#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10)
-#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_DBAT5L CFG_IBAT5L
-#define CFG_DBAT5U CFG_IBAT5U
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
-#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
+#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
-#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT7L CFG_IBAT7L
-#define CFG_DBAT7U CFG_IBAT7U
+#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#else
-#define CFG_IBAT6L (0)
-#define CFG_IBAT6U (0)
-#define CFG_IBAT7L (0)
-#define CFG_IBAT7U (0)
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
-#define CFG_DBAT7L CFG_IBAT7L
-#define CFG_DBAT7U CFG_IBAT7U
+#define CONFIG_SYS_IBAT6L (0)
+#define CONFIG_SYS_IBAT6U (0)
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#endif
/*
#define CONFIG_ETH1ADDR 00:04:9f:ef:04:02
#endif
+#define CONFIG_HAS_FSL_DR_USB
+
#define CONFIG_IPADDR 10.0.0.2
#define CONFIG_SERVERIP 10.0.0.1
#define CONFIG_GATEWAYIP 10.0.0.1
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc8379_rdb.dtb
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
#define XMK_STR(x) #x