#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
#define CONFIG_MPC83XX 1 /* MPC83XX family */
#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
#define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */
+#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
+#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */
/*
* System Clock Setup
#define CFG_SICRL 0x40000000
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
/*
* IMMR new address
#undef CFG_RAMBOOT
#endif
+/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
* FLASH on the Local Bus
*/
#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
BR_V) /* valid */
#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
- OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+ OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
/*
* CS4 on Local Bus, to PIB
*/
-#define CFG_BR4_PRELIM 0xf8008801 /* CS4 base address at 0xf8008000 */
+#define CFG_BR4_PRELIM 0xf8010801 /* CS4 base address at 0xf8010000 */
#define CFG_OR4_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
/*
* CS5 on Local Bus, to PIB
*/
-#define CFG_BR5_PRELIM 0xf8010801 /* CS5 base address at 0xf8010000 */
+#define CFG_BR5_PRELIM 0xf8008801 /* CS5 base address at 0xf8008000 */
#define CFG_OR5_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
/*
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
-#undef CONFIG_OF_FLAT_TREE
#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_HAS_BD_T 1
-#define CONFIG_OF_HAS_UBOOT_ENV 1
-
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
-
-#define OF_CPU "PowerPC,8360@0"
-#define OF_SOC "soc8360@e0000000"
-#define OF_QE "qe@e0100000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc8360@e0000000/serial@4500"
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CFG_PCI_MMIO_BASE 0x90000000
#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE
#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */
-#define CFG_PCI_IO_BASE 0xE0300000
+#define CFG_PCI_IO_BASE 0x00000000
#define CFG_PCI_IO_PHYS 0xE0300000
#define CFG_PCI_IO_SIZE 0x100000 /* 1M */
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_ETHPRIME "FSL UEC0"
#define CONFIG_PHY_MODE_NEED_CHANGE
#define CONFIG_UEC_ETH1 /* GETH1 */
#ifndef CFG_RAMBOOT
#define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+ #define CFG_ENV_SECT_SIZE 0x20000
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
* Command line configuration.
*/
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_SDRAM
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
#define CFG_HID2 HID2_HBE
-/*
- * Cache Config
- */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */
-#endif
-
/*
* MMU Setup
*/
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
/* DDR: cache cacheable */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
#define CONFIG_ETHADDR 00:04:9f:ef:01:01
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:04:9f:ef:01:02
#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
"ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
"fdtaddr=400000\0" \
- "fdtfile=mpc8360emds.dtb\0" \
+ "fdtfile=mpc836x_mds.dtb\0" \
""
#define CONFIG_NFSBOOTCOMMAND \