/*
- * Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+ * Copyright (C) Freescale Semiconductor, Inc. 2006.
*
* See file CREDITS for list of people who contributed to this
* project.
/*
* High Level Configuration Options
*/
-#define CONFIG_MPC834X /* MPC834x family (8343, 8347, 8349) */
+#define CONFIG_MPC834x /* MPC834x family (8343, 8347, 8349) */
#define CONFIG_MPC8349 /* MPC8349 specific */
#define CONFIG_SYS_IMMR 0xE0000000 /* The IMMR is relocated to here */
#ifdef CONFIG_MPC8349ITX
#define CONFIG_COMPACT_FLASH /* The CF card interface on the back of the board */
#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
+#define CONFIG_SATA_SIL3114 /* SIL3114 SATA controller */
+#define CONFIG_SYS_USB_HOST /* use the EHCI USB controller */
#endif
#define CONFIG_PCI
#define CONFIG_FSL_I2C
#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C2_OFFSET 0x3100
#define CONFIG_SYS_SPD_BUS_NUM 1 /* The I2C bus for SPD */
+#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */
#define CONFIG_SYS_I2C_8574_ADDR1 0x20 /* I2C1, PCF8574 */
#define CONFIG_SYS_I2C_8574_ADDR2 0x21 /* I2C1, PCF8574 */
#define ATA_RESET_TIME 1 /* If a CF card is not inserted, time out quickly */
-#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * SATA
+ */
+#ifdef CONFIG_SATA_SIL3114
+
+#define CONFIG_SYS_SATA_MAX_DEVICE 4
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+
+#endif
+
+#ifdef CONFIG_SYS_USB_HOST
+/*
+ * Support USB
+ */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+
+/* Current USB implementation supports the only USB controller,
+ * so we have to choose between the MPH or the DR ones */
+#if 1
+#define CONFIG_HAS_FSL_MPH_USB
+#else
+#define CONFIG_HAS_FSL_DR_USB
+#endif
#endif
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20)
+
#ifdef CONFIG_HARD_I2C
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
#endif
#undef CONFIG_SYS_RAMBOOT
#endif
-#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/*
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
#define CONFIG_SYS_PCI2_IO_SIZE 0x01000000 /* 16M */
#endif
-#define _IO_BASE 0x00000000 /* points to PCI I/O space */
-
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x) (x)
-#endif
-
#ifndef CONFIG_PCI_PNP
#define PCI_ENET0_IOADDR 0x00000000
#define PCI_ENET0_MEMADDR CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SDRAM
+#if defined(CONFIG_COMPACT_FLASH) || defined(CONFIG_SATA_SIL3114) \
+ || defined(CONFIG_USB_STORAGE)
+ #define CONFIG_DOS_PARTITION
+ #define CONFIG_CMD_FAT
+ #define CONFIG_SUPPORT_VFAT
+#endif
+
#ifdef CONFIG_COMPACT_FLASH
#define CONFIG_CMD_IDE
- #define CONFIG_CMD_FAT
+#endif
+
+#ifdef CONFIG_SATA_SIL3114
+ #define CONFIG_CMD_SATA
+#endif
+
+#if defined(CONFIG_SATA_SIL3114) || defined(CONFIG_USB_STORAGE)
+ #define CONFIG_CMD_EXT2
#endif
#ifdef CONFIG_PCI
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#ifdef CONFIG_MPC8349ITX
#define CONFIG_SYS_PROMPT "MPC8349E-mITX> " /* Monitor Command Prompt */
#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
+#define CONFIG_SYS_SCCR_USBMPHCM 3 /* USB MPH controller's clock */
+#define CONFIG_SYS_SCCR_USBDRCM 0 /* USB DR controller's clock */
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH SICRH_TSOBI1 /* Needed for gigabit to work on TSEC 1 */
-#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1)
+#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1) /* USB DR as device + USB MPH as host */
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL CONFIG_SYS_HID0_INIT
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
+ BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L 0
*/
#define CONFIG_ENV_OVERWRITE
-#ifdef CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR 00:E0:0C:00:8C:01
-#endif
-
-#ifdef CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:E0:0C:00:8C:02
-#endif
-
-#define CONFIG_IPADDR 192.168.1.253
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.252.0
#define CONFIG_NETDEV eth0
#ifdef CONFIG_MPC8349ITX
#define CONFIG_FDTFILE mpc8349emitxgp.dtb
#endif
-#define CONFIG_BOOTDELAY 0
+#define CONFIG_BOOTDELAY 6
#define XMK_STR(x) #x
#define MK_STR(x) XMK_STR(x)
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
- "fdtaddr=400000\0" \
+ "fdtaddr=780000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"
#define CONFIG_NFSBOOTCOMMAND \