*/
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC83XX 1 /* MPC83XX family */
+#define CONFIG_MPC834X 1 /* MPC834X family */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
-#define CFG_IMMRBAR 0xE0000000
+#define CFG_IMMR 0xE0000000
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00000000 /* memtest region */
/*
* DDR Setup
*/
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_DDR_ECC /* support DDR ECC function */
#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_BASE
#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
+ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#undef CONFIG_DDR_2T_TIMING
+/*
+ * DDRCDR - DDR Control Driver Register
+ */
+#define CFG_DDRCDR_VALUE 0x80080001
+
#if defined(CONFIG_SPD_EEPROM)
/*
* Determine DDR configuration from I2C interface.
* Manually set up DDR parameters
*/
#define CFG_DDR_SIZE 256 /* MB */
+#if defined(CONFIG_DDR_II)
+#define CFG_DDRCDR 0x80080001
+#define CFG_DDR_CS2_BNDS 0x0000000f
+#define CFG_DDR_CS2_CONFIG 0x80330102
+#define CFG_DDR_TIMING_0 0x00220802
+#define CFG_DDR_TIMING_1 0x38357322
+#define CFG_DDR_TIMING_2 0x2f9048c8
+#define CFG_DDR_TIMING_3 0x00000000
+#define CFG_DDR_CLK_CNTL 0x02000000
+#define CFG_DDR_MODE 0x47d00432
+#define CFG_DDR_MODE2 0x8000c000
+#define CFG_DDR_INTERVAL 0x03cf0080
+#define CFG_DDR_SDRAM_CFG 0x43000000
+#define CFG_DDR_SDRAM_CFG2 0x00401000
+#else
#define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
#define CFG_DDR_TIMING_1 0x36332321
#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
#define CFG_DDR_MODE 0x00000022 /* DLL,normal,seq,4/2.5, 4 burst len */
#endif
#endif
+#endif
/*
* SDRAM on the Local Bus
#define CFG_FLASH_CFI /* use the Common Flash Interface */
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
-#define CFG_FLASH_SIZE 8 /* flash size in MB */
+#define CFG_FLASH_SIZE 32 /* max flash size in MB */
/* #define CFG_FLASH_USE_BUFFER_WRITE */
#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \
- (2 << BR_PS_SHIFT) | /* 32 bit port size */ \
+ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
BR_V) /* valid */
-
-#define CFG_OR0_PRELIM 0xFF806FF7 /* 8 MB flash size */
+#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
+ OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */
-#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */
+#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32 MB window size */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
+#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
#define CFG_LBC_LBCR 0x00000000
-#define CFG_LB_SDRAM /* if board has SRDAM on local bus */
+/*
+ * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
+ * if board has SRDAM on local bus, you can define CFG_LB_SDRAM
+ */
+#undef CFG_LB_SDRAM
#ifdef CFG_LB_SDRAM
/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_IMMRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8349@0"
+#define OF_SOC "soc8349@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500"
+
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
#define CFG_I2C2_OFFSET 0x3100
/* TSEC */
#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMRBAR+CFG_TSEC1_OFFSET)
+#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMRBAR+CFG_TSEC2_OFFSET)
+#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
/* USB */
#define CFG_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */
#endif
#define CONFIG_GMII 1 /* MII PHY management */
-#define CONFIG_MPC83XX_TSEC1 1
-#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0"
-#define CONFIG_MPC83XX_TSEC2 1
-#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT)
-#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_PCI \
- | CFG_CMD_I2C \
- | CFG_CMD_DATE) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_LOADS))
-#else
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_DATE) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_LOADS))
-#endif
-#else
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_MII
+
#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_DATE \
- )
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_MII \
- | CFG_CMD_DATE \
- )
+ #define CONFIG_CMD_PCI
#endif
+
+#if defined(CFG_RAMBOOT)
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
#endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
#endif
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CFG_IBAT5L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT5U (CFG_IMMRBAR | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
#define CFG_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHADDR 00:04:9f:ef:23:33
#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
#define CONFIG_ETH1ADDR 00:E0:0C:00:7E:21
#endif
-#define CONFIG_IPADDR 192.168.205.5
+#define CONFIG_IPADDR 192.168.1.253
#define CONFIG_HOSTNAME mpc8349emds
-#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx
-#define CONFIG_BOOTFILE /tftpboot/tqm83xx/uImage
+#define CONFIG_ROOTPATH /nfsroot/rootfs
+#define CONFIG_BOOTFILE uImage
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "bootfile=/tftpboot/mpc8349emds/uImage\0" \
"load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \
"update=protect off fe000000 fe03ffff; " \
"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0" \
"upd=run load;run update\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8349emds.dtb\0" \
""
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
#define CONFIG_BOOTCOMMAND "run flash_self"
#endif /* __CONFIG_H */
projects / oweals / u-boot.git / blobdiff