#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
*/
#define CFG_IMMR 0xE0000000
+/*
+ * System performance
+ */
+#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CFG_SPCR_OPT 1 /* (0-1) Optimize transactions between CSB and the SEC and QUICC Engine block */
+
/*
* DDR Setup
*/
/* Manually set up DDR parameters
*/
#define CFG_DDR_SIZE 64 /* MB */
-#define CFG_DDR_CS0_CONFIG 0x80840101
-#define CFG_DDR_TIMING_0 0x00220802
-#define CFG_DDR_TIMING_1 0x3935d322
-#define CFG_DDR_TIMING_2 0x0f9048ca
+#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \
+ | CSCONFIG_ODT_WR_ACS \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9 )
+ /* 0x80010101 */
+#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_RRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WWT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+ | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+ /* 0x00220802 */
+#define CFG_DDR_TIMING_1 ( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+ | ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
+ | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+ | ( 3 << TIMING_CFG1_REFREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+ /* 0x26253222 */
+#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | (31 << TIMING_CFG2_CPO_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+ | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+ | ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x1f9048c7 */
#define CFG_DDR_TIMING_3 0x00000000
-#define CFG_DDR_CLK_CNTL 0x02000000
-#define CFG_DDR_MODE 0x44400232
+#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+ /* 0x02000000 */
+#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+ /* 0x44480232 */
#define CFG_DDR_MODE2 0x8000c000
-#define CFG_DDR_INTERVAL 0x03200064
+#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x03200064 */
#define CFG_DDR_CS0_BNDS 0x00000003
-#define CFG_DDR_SDRAM_CFG 0x43080000
+#define CFG_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE )
+ /* 0x43080000 */
#define CFG_DDR_SDRAM_CFG2 0x00401000
#endif
* FLASH on the Local Bus
*/
#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CFG_FLASH_SIZE 16 /* FLASH size is 16M */
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_CPU "PowerPC,8323@0"
-#define OF_SOC "soc8323@e0000000"
-#define OF_QE "qe@e0100000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc8323@e0000000/serial@4500"
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CFG_I2C_OFFSET 0x3000
/*
- * Config on-board RTC
+ * Config on-board EEPROM
*/
-#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_PAGE_WRITE_BITS 6
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*
* General PCI
#define CFG_PCI1_IO_SIZE 0x04000000 /* 64M */
#ifdef CONFIG_PCI
-
+#define CONFIG_PCI_SKIP_HOST_BRIDGE
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_ETHPRIME "FSL UEC0"
#define CONFIG_UEC_ETH1 /* ETH3 */
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ASKENV
#if defined(CONFIG_PCI)
#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
#define CFG_HID2 HID2_HBE
-/*
- * Cache Config
- */
-#define CFG_DCACHE_SIZE 16384
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */
-#endif
-
/*
* MMU Setup
*/
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR: cache cacheable */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
*/
#define CONFIG_ENV_OVERWRITE
+#define CONFIG_HAS_ETH0 /* add support for "ethaddr" */
#define CONFIG_ETHADDR 00:04:9f:ef:03:01
#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */
#define CONFIG_ETH1ADDR 00:04:9f:ef:03:02
+/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM (see CFG_I2C_EEPROM) */
+#define CFG_I2C_MAC_OFFSET 0x7f00 /* MAC address offset in I2C EEPROM */
+
#define CONFIG_IPADDR 10.0.0.2
#define CONFIG_SERVERIP 10.0.0.1
#define CONFIG_GATEWAYIP 10.0.0.1
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc832x_rdb.dtb
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200