drivers/video/am335x-fb: Properly point framebuffer behind palette

[oweals/u-boot.git] / include / configs / MPC8313ERDB.h

diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h
index 69b2cb197056dedee2fbc91d49c1f48d6a5e7b08..fda894e119814d58c24c4c2eecb4b5b94dcd7785 100644 (file)
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB.h
@@ -10,6 +10,8 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_DISPLAY_BOARDINFO
+
 /*
  * High Level Configuration Options
  */
@@ -19,7 +21,6 @@
 #define CONFIG_MPC8313ERDB     1
 
 #ifdef CONFIG_NAND
-#define CONFIG_SPL
 #define CONFIG_SPL_INIT_MINIMAL
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
@@ -270,13 +271,11 @@
        "mtdparts=e2800000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)"
 
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND 1
 #define CONFIG_NAND_FSL_ELBC 1
 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384
 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
 
-
 #define CONFIG_SYS_NAND_BR_PRELIM      (CONFIG_SYS_NAND_BASE \
                                | BR_DECC_CHK_GEN       /* Use HW ECC */ \
                                | BR_PS_8               /* 8 bit port */ \
@@ -359,19 +358,12 @@
 
 #endif
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
-#define CONFIG_OF_STDOUT_VIA_ALIAS     1
-
 #define CONFIG_MPC83XX_GPIO 1
-#define CONFIG_CMD_GPIO 1
 
 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX      1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 
@@ -381,9 +373,6 @@
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
@@ -437,7 +426,6 @@
 #define TSEC2_PHYIDX           0
 #endif
 
-
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME                        "TSEC1"
 
@@ -484,24 +472,12 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_PCI
 
-#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#endif
-
 #define CONFIG_CMDLINE_EDITING 1
 #define CONFIG_AUTO_COMPLETE   /* add autocompletion support   */