*/
#define CONFIG_E300 1 /* E300 family */
#define CONFIG_MPC83xx 1 /* MPC83xx family */
+#define CONFIG_MPC830x 1 /* MPC830x family */
#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
#define CONFIG_MPC8308RDB 1 /* MPC8308RDB board specific */
#define CONFIG_MISC_INIT_R
+/* new uImage format support */
+#define CONFIG_FIT 1
+#define CONFIG_FIT_VERBOSE 1
+
+#define CONFIG_MMC 1
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+#define CONFIG_SYS_FSL_ESDHC_USE_PIO
+
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
/*
* On-board devices
*
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | 0x00010000 /* ODT_WR to CSn */ \
+ | CSCONFIG_ODT_RD_NEVER \
+ | CSCONFIG_ODT_WR_ONLY_CURRENT \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
/* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
/* 0x03600100 */
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
- | SDRAM_CFG_32_BE)
+ | SDRAM_CFG_DBW_32)
/* 0x43080000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
-#define CONFIG_SYS_BR0_PRELIM (\
- CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
- (2 << BR_PS_SHIFT) /* 16 bit port size */ |\
- BR_V) /* valid */
-#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
+ | BR_PS_16 /* 16 bit port */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 \
| OR_GPCM_XACS \
| OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX \
- | OR_GPCM_EHTR \
- | OR_GPCM_EAD)
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
/* 127 64KB sectors and 8 8KB top sectors per device */
* NAND Flash on the Local Bus
*/
#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */
+#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* 8 bit port */ \
+ | BR_DECC_CHK_GEN /* Use HW ECC */ \
+ | BR_PS_8 /* 8 bit Port */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
-#define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 /* length 32K */ \
+#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
| OR_FCM_CSCT \
| OR_FCM_CST \
| OR_FCM_CHT \
#ifdef CONFIG_VSC7385_ENET
#define CONFIG_TSEC2
+ /* VSC7385 Base address on CS2 */
#define CONFIG_SYS_VSC7385_BASE 0xF0000000
-#define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
-#define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
+#define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VSC7385_BASE \
+ | BR_PS_8 /* 8-bit port */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+ /* 0xF0000801 */
+#define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_SETA \
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET)
+ /* 0xFFFE09FF */
/* Access window base at VSC7385 base */
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
/* Access window size 128K */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C2_OFFSET 0x3100
+/*
+ * SPI on header J8
+ *
+ * WARNING: enabling this will break TSEC2 (connected to the Vitesse switch)
+ * due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins.
+ */
+#ifdef CONFIG_MPC8XXX_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_USE_SPIFLASH
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#endif
/*
* Board info - revision and where boot from
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
-#define xstr(s) str(s)
-#define str(s) #s
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
"bootcmd=run flash_self\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
- "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \
+ "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
" +${filesize};cp.b ${fileaddr} " \
- xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
"upd=run load update\0" \
#endif /* __CONFIG_H */