* for FCC)
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
*/
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
*/
#define SPD_EEPROM_ADDRESS 0x50
-
#define CONFIG_8260_CLKIN 66000000 /* in Hz */
#define CONFIG_BAUDRATE 115200
-
/*
* Command line configuration.
*/
-#include <config_cmd_all.h>
-
-#undef CONFIG_CMD_BEDBUG
-#undef CONFIG_CMD_BMP
-#undef CONFIG_CMD_BSP
-#undef CONFIG_CMD_DATE
-#undef CONFIG_CMD_DHCP
-#undef CONFIG_CMD_DISPLAY
-#undef CONFIG_CMD_DOC
-#undef CONFIG_CMD_DTT
-#undef CONFIG_CMD_EEPROM
-#undef CONFIG_CMD_ELF
-#undef CONFIG_CMD_EXT2
-#undef CONFIG_CMD_FDC
-#undef CONFIG_CMD_FDOS
-#undef CONFIG_CMD_HWFLOW
-#undef CONFIG_CMD_IDE
-#undef CONFIG_CMD_JFFS2
-#undef CONFIG_CMD_KGDB
-#undef CONFIG_CMD_MMC
-#undef CONFIG_CMD_NAND
-#undef CONFIG_CMD_PCMCIA
-#undef CONFIG_CMD_REISER
-#undef CONFIG_CMD_SCSI
-#undef CONFIG_CMD_SPI
-#undef CONFIG_CMD_SNTP
-#undef CONFIG_CMD_VFD
-#undef CONFIG_CMD_UNIVERSE
-#undef CONFIG_CMD_USB
-#undef CONFIG_CMD_XIMG
+#include <config_cmd_default.h>
+
+/* Commands we want, that are not part of default set */
+#define CONFIG_CMD_ASKENV /* ask for env variable */
+#define CONFIG_CMD_CACHE /* icache, dcache */
+#define CONFIG_CMD_DHCP /* DHCP Support */
+#define CONFIG_CMD_DIAG /* Diagnostics */
+#define CONFIG_CMD_IMMAP /* IMMR dump support */
+#define CONFIG_CMD_IRQ /* irqinfo */
+#define CONFIG_CMD_MII /* MII support */
+#define CONFIG_CMD_PCI /* pciinfo */
+#define CONFIG_CMD_PING /* ping support */
+#define CONFIG_CMD_PORTIO /* Port I/O */
+#define CONFIG_CMD_REGINFO /* Register dump */
+#define CONFIG_CMD_SAVES /* save S record dump */
+#define CONFIG_CMD_SDRAM /* SDRAM DIMM SPD info printout */
+
+/* Commands from default set we don't need */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
/* Define a command string that is automatically executed when no character
* is read on the console interface withing "Boot Delay" after reset.
"bootm"
#endif /* CONFIG_BOOT_ROOT_NFS */
-/* Add support for a few extra bootp options like:
- * - File size
- * - DNS
+/*
+ * BOOTP options
*/
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
- CONFIG_BOOTP_BOOTFILESIZE | \
- CONFIG_BOOTP_DNS)
-
-
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define SDRAM_SPD_ADDR 0x50
-
/*-----------------------------------------------------------------------
* BR2,BR3 - Base Register
* Ref: Section 10.3.1 on page 10-14
#error "INVALID SDRAM CONFIGURATION"
#endif
-
#define RS232EN_1 0x02000002
#define RS232EN_2 0x01000001
#define FETHIEN 0x08000008
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
/* Use this HRCW for booting from address 0xfe00000 (JP3 in setting 1-2) */
/* 0x0EB2B645 */
#define CFG_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP ) |\
# define CFG_ENV_SIZE 0x200
#endif /* CFG_RAMBOOT */
-
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if defined(CONFIG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
-
/*-----------------------------------------------------------------------
* HIDx - Hardware Implementation-dependent Registers 2-11
*-----------------------------------------------------------------------