***********************************************************/
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-/***********************************************************
- * Command definitions
- ***********************************************************/
-#define MIP405_COMMON_CMDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_CACHE | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_IRQ | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SAVES | \
- CFG_CMD_BSP )
-#if defined(CONFIG_MIP405T)
-#define CONFIG_COMMANDS \
- MIP405_COMMON_CMDS
-#else
-#define CONFIG_COMMANDS \
- (MIP405_COMMON_CMDS | \
- CFG_CMD_USB | \
- CFG_CMD_DOC )
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_BSP
+
+#if !defined(CONFIG_MIP405T)
+ #define CONFIG_CMD_USB
+ #define CONFIG_CMD_DOC
#endif
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-#define CFG_NAND_LEGACY
+#define CONFIG_NAND_LEGACY
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/**************************************************************
* I2C Stuff:
* the MIP405 is equiped with an Atmel 24C128/256 EEPROM at address
***************************************************************/
#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 50000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CFG_I2C_EEPROM_ADDR 0x53 /* EEPROM 24C128/256 */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 /* EEPROM 24C128/256 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
-#undef CFG_I2C_EEPROM_ADDR_OVERFLOW
-#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */
+#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */
/* 64 byte page write mode using*/
/* last 6 bits of the address */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE /* enable Page write */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x00000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x00800 /* 2k bytes may be used for env vars */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x00000 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x00800 /* 2k bytes may be used for env vars */
/***************************************************************
* Definitions for Serial Presence Detect EEPROM address
* (to get SDRAM settings)
***************************************************************/
/*#define SDRAM_EEPROM_WRITE_ADDRESS 0xA0
-#define SDRAM_EEPROM_READ_ADDRESS 0xA1
+#define SDRAM_EEPROM_READ_ADDRESS 0xA1
*/
/**************************************************************
* Environment definitions
#define CONFIG_BOOTDELAY 5
/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */
#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
/***************************************************************
* defines if the console is stored in the environment
***************************************************************/
-#define CFG_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
/***************************************************************
* defines if an overwrite_console function exists
*************************************************************/
-#define CFG_CONSOLE_OVERWRITE_ROUTINE
-#define CFG_CONSOLE_INFO_QUIET
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
/***************************************************************
* defines if the overwrite_console should be stored in the
* environment
**************************************************************/
-#undef CFG_CONSOLE_ENV_OVERWRITE
+#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
/**************************************************************
* loads config
*************************************************************/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MISC_INIT_R
/***********************************************************
* Miscellaneous configurable options
**********************************************************/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_BASE_BAUD 916667
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD 916667
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
-#define CFG_LOAD_ADDR 0x400000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*-----------------------------------------------------------------------
* PCI stuff
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */
#define CONFIG_PCI_PNP /* pci plug-and-play */
/* resource configuration */
-#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
-#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
-#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
+#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFFF80000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=mip405-0"
#define MTDPARTS_DEFAULT "mtdparts=mip405-0:-(jffs2)"
*/
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 0x4000 /* For AMCC 405GPr CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*-----------------------------------------------------------------------
* Logbuffer Configuration
*/
-#undef CONFIG_LOGBUFFER /* supported but not enabled */
+#undef CONFIG_LOGBUFFER /* supported but not enabled */
/*-----------------------------------------------------------------------
* Bootcountlimit Configuration
*/
* POST Configuration
*/
#if 0 /* enable this if POST is desired (is supported but not enabled) */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_RTC | \
- CFG_POST_I2C)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_RTC | \
+ CONFIG_SYS_POST_I2C)
#endif
/*
#define PER_UART1_ADDR 0xF4200000 /* smallest window is 1MByte 0x10 0000*/
#define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
-#define CONFIG_PORT_ADDR PER_PLD_ADDR + 5
+#define CONFIG_PORT_ADDR PER_PLD_ADDR + 5
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in On Chip SRAM)
*/
-#define CFG_TEMP_STACK_OCM 1
-#define CFG_OCM_DATA_ADDR 0xF0000000
-#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of On Chip SRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of On Chip SRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 32)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 32)
#ifdef CONFIG_POST /* reserve one word for POST Info */
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
+#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 4)
#endif
#ifdef CONFIG_BOOTCOUNT_LIMIT /* reserve 2 word for bootcount limit */
-#define CFG_BOOTCOUNT_ADDR (CFG_GBL_DATA_OFFSET - 12)
+#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 12)
#endif
/*
/***********************************************************************
* External peripheral base address
***********************************************************************/
-#define CFG_ISA_IO_BASE_ADDRESS 0xE8000000
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
/***********************************************************************
* Last Stage Init
/************************************************************
* Ethernet Stuff
***********************************************************/
+#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
#define CONFIG_PHY_RESET_DELAY 300 /* Intel LXT971A needs this */
* IDE/ATA stuff
************************************************************/
#if defined(CONFIG_MIP405T)
-#define CFG_IDE_MAXBUS 1 /* MIP405T has only one IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* MIP405T has only one IDE bus */
#else
-#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
+#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
#endif
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR CFG_ISA_IO_BASE_ADDRESS /* base address */
-#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
-#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
-#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CFG_ATA_REG_OFFSET 0 /* reg offset */
-#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
+#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */
+#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
/************************************************************
* Disk-On-Chip configuration
************************************************************/
-#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
-#define CFG_DOC_SHORT_TIMEOUT
-#define CFG_DOC_SUPPORT_2000
-#define CFG_DOC_SUPPORT_MILLENNIUM
+#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
+#define CONFIG_SYS_DOC_SHORT_TIMEOUT
+#define CONFIG_SYS_DOC_SUPPORT_2000
+#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
/************************************************************
* Keyboard support
************************************************************/
#define CONFIG_USB_STORAGE
/* Enable needed helper functions */
-#define CFG_DEVICE_DEREGISTER /* needs device_deregister */
+#define CONFIG_SYS_DEVICE_DEREGISTER /* needs device_deregister */
#endif
/************************************************************
* Debug support
************************************************************/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif