#ifndef _M5271EVB_H
#define _M5271EVB_H
-#define DEBUG
-#undef DEBUG
-
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_M5271 /* define processor type */
#define CONFIG_M5271EVB /* define board type */
-#define CONFIG_IPADDR 192.168.30.1
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_ETHADDR 00:06:3b:01:41:55
+#define CONFIG_MCFTMR
+#define CONFIG_MCFUART
+#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 19200
#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
#undef CONFIG_WATCHDOG /* disable watchdog */
-#define CONFIG_BOOTDELAY 5
-
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CFG_ENV_OFFSET 0x4000
-#define CFG_ENV_SECT_SIZE 0x2000
-#define CFG_ENV_IS_IN_FLASH 1
#else
#define CFG_ENV_ADDR 0xffe04000
+#endif
#define CFG_ENV_SECT_SIZE 0x2000
#define CFG_ENV_IS_IN_FLASH 1
-#endif
+#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
#define CONFIG_CMD_PING
#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_LOADB
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+# define CONFIG_NET_MULTI 1
+# define CONFIG_MII 1
+# define CONFIG_MII_INIT 1
+# define CFG_DISCOVER_PHY
+# define CFG_RX_ETH_BUFFER 8
+# define CFG_FAULT_ECHO_LINK_DOWN
+
+# define CFG_FEC0_PINMUX 0
+# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE
+# define MCFFEC_TOUT_LOOP 50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+# ifndef CFG_DISCOVER_PHY
+# define FECDUPLEX FULL
+# define FECSPEED _100BASET
+# else
+# ifndef CFG_FAULT_ECHO_LINK_DOWN
+# define CFG_FAULT_ECHO_LINK_DOWN
+# endif
+# endif /* CFG_DISCOVER_PHY */
+#endif
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C /* I2C with hw support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 80000
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_OFFSET 0x00000300
+#define CFG_IMMR CFG_MBAR
+
+#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
+#define CONFIG_BOOTFILE "u-boot.bin"
+#ifdef CONFIG_MCFFEC
+# define CONFIG_NET_RETRY_COUNT 5
+# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
+# define CONFIG_IPADDR 192.162.1.2
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_SERVERIP 192.162.1.1
+# define CONFIG_GATEWAYIP 192.162.1.1
+# define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif /* FEC_ENET */
+
+#define CONFIG_HOSTNAME M5235EVB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "loadaddr=10000\0" \
+ "u-boot=u-boot.bin\0" \
+ "load=tftp ${loadaddr) ${u-boot}\0" \
+ "upd=run load; run prog\0" \
+ "prog=prot off ffe00000 ffe2ffff;" \
+ "era ffe00000 ffe2ffff;" \
+ "cp.b ${loadaddr} 0 ${filesize};" \
+ "save\0" \
+ ""
#define CFG_PROMPT "=> "
-#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_LOAD_ADDR 0x00100000
#define CFG_MBAR 0x40000000 /* Register Base Addrs */
-/* Enable FEC ethernet */
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT 5
-#define CFG_ENET_BD_BASE 0x480000
-
/*
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR 0x20000000
-#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
+#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CFG_FLASH_BASE 0xffe00000
#ifdef CONFIG_MONITOR_IS_IN_RAM
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
/* FLASH organization */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 1000
#define CFG_FLASH_CFI 1
-#define CFG_FLASH_CFI_DRIVER 1
+#define CONFIG_FLASH_CFI_DRIVER 1
#define CFG_FLASH_SIZE 0x200000
/* Cache Configuration */
/* Port configuration */
#define CFG_FECI2C 0xF0
-#endif /* _M5271EVB_H */
+#endif /* _M5271EVB_H */