#define CONFIG_BOOTCOUNT_LIMIT
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CFG_NS16550_COM1 (CFG_UART_BASE + 0x8000)
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_CPU "PowerPC,8247@0"
+#define OF_SOC "soc@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc@f0000000/serial8250@e0008000"
+
+
/*
* select ethernet configuration
*
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
+#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
+#define CONFIG_ETHER_ON_FCC1
+#define FCC_ENET
/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
+ * - Rx-CLK is CLK10
+ * - Tx-CLK is CLK9
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK10|CMXFCR_TF1CS_CLK9)
# define CFG_CPMFCR_RAMTYPE 0
# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_RTC_PCF8563
+#define CFG_I2C_RTC_ADDR 0x51
/*
* Command line configuration.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_FLASH_BANKS_LIST { 0xFF800000 }
+#define CFG_MAX_FLASH_BANKS_DETECT 1
/* What should the base address of the main FLASH be and how big is
* it (in MBytes)? This must contain TEXT_BASE from board/ids8247/config.mk
* The main FLASH is whichever is connected to *CS0.
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CFG_MAX_FLASH_SECT 64 /* max num of sects on one chip */
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
*/
#if defined(CONFIG_CMD_NAND)
-#define CFG_NAND_LEGACY
+#define CONFIG_NAND_LEGACY
#define CFG_NAND0_BASE 0xE1000000
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)(adr + 0x0)) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)(adr + 0x0)))
-#endif /* CFG_CMD_NAND */
+#endif /* CONFIG_CMD_NAND */
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*/
#define CFG_OR2 ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A10 |\
+ ORxS_ROWST_PBI0_A9 |\
ORxS_NUMR_12)
-#define CFG_PSDMR (PSDMR_SDAM_A13_IS_A5 |\
+#define CFG_PSDMR (PSDMR_SDAM_A14_IS_A5 |\
PSDMR_BSMA_A15_A17 |\
- PSDMR_SDA10_PBI0_A11 |\
+ PSDMR_SDA10_PBI0_A10 |\
PSDMR_RFRC_5_CLK |\
PSDMR_PRETOACT_2W |\
PSDMR_ACTTORW_2W |\