ARMV7: OMAP3: Add CONFIG_SYS_NAND_QUIET_TEST to Beagle and Overo configs

[oweals/u-boot.git] / include / configs / DU440.h

diff --git a/include/configs/DU440.h b/include/configs/DU440.h
index 508a0cae3d830c2fda8e5fa7f8fb447a328a9563..830466f7a8dfd42a7901863bed915e19794f6b5b 100644 (file)
--- a/include/configs/DU440.h
+++ b/include/configs/DU440.h
@@ -60,8 +60,9 @@
 #define CONFIG_SYS_PCI_MEMBASE1        CONFIG_SYS_PCI_MEMBASE  + 0x10000000
 #define CONFIG_SYS_PCI_MEMBASE2        CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
 #define CONFIG_SYS_PCI_MEMBASE3        CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-#define CONFIG_SYS_PCI_IOBASE          0xe8000000
-
+#define CONFIG_SYS_PCI_IOBASE          0xe8000000
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH
+#define CONFIG_SYS_PCI_SUBSYS_ID       0x0444          /* device ID for DU440 */
 
 /* Don't change either of these */
 #define CONFIG_SYS_PERIPHERAL_BASE     0xef600000      /* internal peripherals */
@@ -168,9 +169,9 @@
  */
 #define CONFIG_HARD_I2C                1       /* I2C with hardware support    */
 #undef CONFIG_SOFT_I2C                 /* I2C bit-banged               */
+#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
 #define CONFIG_SYS_I2C_SPEED           100000  /* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE           0x7F
-#define CONFIG_I2C_CMD_TREE     1
 #define CONFIG_I2C_MULTI_BUS    1
 
 #define CONFIG_SYS_SPD_BUS_NUM         0
@@ -253,6 +254,7 @@
 int du440_phy_addr(int devnum);
 #endif
 
+#define CONFIG_PPC4xx_EMAC
 #define        CONFIG_IBM_EMAC4_V4     1
 #define CONFIG_MII             1       /* MII PHY management           */
 #define CONFIG_PHY_ADDR                du440_phy_addr(0) /* PHY address        */
@@ -289,14 +291,13 @@ int du440_phy_addr(int devnum);
 
 #include <config_cmd_default.h>
 
-#define CONFIG_CMD_AUTOSCRIPT
-#define CONFIG_CMD_BSP
+#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_BMP
+#define CONFIG_CMD_BSP
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
 #define CONFIG_CMD_DIAG
+#define CONFIG_CMD_DTT
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_FAT
@@ -308,9 +309,10 @@ int du440_phy_addr(int devnum);
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SOURCE
+#define CONFIG_CMD_USB
 
 #define CONFIG_SUPPORT_VFAT
 
@@ -410,7 +412,6 @@ int du440_phy_addr(int devnum);
  * NAND FLASH
  */
 #define CONFIG_SYS_MAX_NAND_DEVICE     2
-#define NAND_MAX_CHIPS         CONFIG_SYS_MAX_NAND_DEVICE
 #define CONFIG_SYS_NAND_SELECT_DEVICE  1       /* nand driver supports mutipl. chips */
 #define CONFIG_SYS_NAND_BASE_LIST      {CONFIG_SYS_NAND0_ADDR + CONFIG_SYS_NAND0_CS, \
                                 CONFIG_SYS_NAND1_ADDR + CONFIG_SYS_NAND1_CS}
@@ -428,7 +429,7 @@ int du440_phy_addr(int devnum);
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
-#define CONFIG_AUTOSCRIPT      1
+#define CONFIG_SOURCE          1
 
 #define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP