#define CONFIG_MII 1 /* MII PHY management */
#ifndef CONFIG_EXT_PHY
-#define CONFIG_PHY_ADDR 0 /* EMAC0 PHY address */
-#define CONFIG_PHY1_ADDR 1 /* EMAC1 PHY address */
+#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */
+#define CONFIG_PHY1_ADDR 16 /* EMAC1 PHY address */
#else
#define CONFIG_PHY_ADDR 2 /* PHY address */
#endif
*/
#define CFG_NAND0_BASE 0xFF400000
#define CFG_NAND1_BASE 0xFF000000
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE }
+#define NAND_BIG_DELAY_US 25
/* For CATcenter there is only NAND on the module */
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CFG_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */
-#define NAND_DISABLE_CE(nand) do \
+#define MACRO_NAND_DISABLE_CE(nandptr) do \
{ \
- switch((unsigned long)(((struct nand_chip *)nand)->IO_ADDR)) \
+ switch((unsigned long)nandptr) \
{ \
case CFG_NAND0_BASE: \
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CE); \
} \
} while(0)
-#define NAND_ENABLE_CE(nand) do \
+#define MACRO_NAND_ENABLE_CE(nandptr) do \
{ \
- switch((unsigned long)(((struct nand_chip *)nand)->IO_ADDR)) \
+ switch((unsigned long)nandptr) \
{ \
case CFG_NAND0_BASE: \
out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_CE); \
} \
} while(0)
-
-#define NAND_CTL_CLRALE(nandptr) do \
+#define MACRO_NAND_CTL_CLRALE(nandptr) do \
{ \
switch((unsigned long)nandptr) \
{ \
} \
} while(0)
-#define NAND_CTL_SETALE(nandptr) do \
+#define MACRO_NAND_CTL_SETALE(nandptr) do \
{ \
switch((unsigned long)nandptr) \
{ \
} \
} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do \
+#define MACRO_NAND_CTL_CLRCLE(nandptr) do \
{ \
switch((unsigned long)nandptr) \
{ \
} \
} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { \
+#define MACRO_NAND_CTL_SETCLE(nandptr) do { \
switch((unsigned long)nandptr) { \
case CFG_NAND0_BASE: \
out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CLE); \
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
-#endif
-
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */
/* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#endif /* CONFIG_NO_SERIAL_EEPROM */
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#define CONFIG_JFFS2_NAND_DEV 0 /* nand device jffs2 lives on */
-#define CONFIG_JFFS2_NAND_OFF 0 /* start of jffs2 partition */
-#define CONFIG_JFFS2_NAND_SIZE 2*1024*1024 /* size of jffs2 partition */
#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
+/*
+ * JFFS2 partitions
+ *
+ */
+/* No command line, one static partition */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nand"
+#define CONFIG_JFFS2_PART_SIZE 0x00200000
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support
+ *
+ * Note: fake mtd_id used, no linux mtd map file
+ */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nand0=catcenter"
+#define MTDPARTS_DEFAULT "mtdparts=catcenter:2m(nand)"
+*/
+
#endif /* __CONFIG_H */