#define __DISABLE_MACHINE_EXCEPTION__
#ifdef __DEBUG_START_FROM_SRAM__
-#define CFG_DUMMY_FLASH_SIZE 1024*1024*4
+#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4
#endif
/*
#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#undef CONFIG_EXT_PHY
#define CONFIG_MII 1 /* MII PHY management */
#ifndef CONFIG_EXT_PHY
-#define CONFIG_PHY_ADDR 0 /* EMAC0 PHY address */
-#define CONFIG_PHY1_ADDR 1 /* EMAC1 PHY address */
+#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */
+#define CONFIG_PHY1_ADDR 16 /* EMAC1 PHY address */
#else
#define CONFIG_PHY_ADDR 2 /* PHY address */
#endif
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
- CFG_CMD_ELF | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_NAND | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP )
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_HUSH_PARSER /* use "hush" command parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD 691200
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
-#define CFG_NAND0_BASE 0xFF400000
-#define CFG_NAND1_BASE 0xFF000000
+#define CONFIG_SYS_NAND0_BASE 0xFF400000
+#define CONFIG_SYS_NAND1_BASE 0xFF000000
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE }
+#define NAND_BIG_DELAY_US 25
/* For CATcenter there is only NAND on the module */
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define NAND_NO_RB
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-#define CFG_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CFG_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CFG_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CFG_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-#define CFG_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */
-#define CFG_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */
-#define CFG_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */
-#define CFG_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */
+#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */
+#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */
+#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */
+#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */
-#define NAND_DISABLE_CE(nand) do \
+#define MACRO_NAND_DISABLE_CE(nandptr) do \
{ \
- switch((unsigned long)(((struct nand_chip *)nand)->IO_ADDR)) \
+ switch((unsigned long)nandptr) \
{ \
- case CFG_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CE); \
+ case CONFIG_SYS_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \
break; \
- case CFG_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_CE); \
+ case CONFIG_SYS_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \
break; \
} \
} while(0)
-#define NAND_ENABLE_CE(nand) do \
+#define MACRO_NAND_ENABLE_CE(nandptr) do \
{ \
- switch((unsigned long)(((struct nand_chip *)nand)->IO_ADDR)) \
+ switch((unsigned long)nandptr) \
{ \
- case CFG_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_CE); \
+ case CONFIG_SYS_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \
break; \
- case CFG_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_CE); \
+ case CONFIG_SYS_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \
break; \
} \
} while(0)
-
-#define NAND_CTL_CLRALE(nandptr) do \
+#define MACRO_NAND_CTL_CLRALE(nandptr) do \
{ \
switch((unsigned long)nandptr) \
{ \
- case CFG_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_ALE); \
+ case CONFIG_SYS_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \
break; \
- case CFG_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_ALE); \
+ case CONFIG_SYS_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \
break; \
} \
} while(0)
-#define NAND_CTL_SETALE(nandptr) do \
+#define MACRO_NAND_CTL_SETALE(nandptr) do \
{ \
switch((unsigned long)nandptr) \
{ \
- case CFG_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_ALE); \
+ case CONFIG_SYS_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \
break; \
- case CFG_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_ALE); \
+ case CONFIG_SYS_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \
break; \
} \
} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do \
+#define MACRO_NAND_CTL_CLRCLE(nandptr) do \
{ \
switch((unsigned long)nandptr) \
{ \
- case CFG_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_CLE); \
+ case CONFIG_SYS_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \
break; \
- case CFG_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_CLE); \
+ case CONFIG_SYS_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \
break; \
} \
} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { \
+#define MACRO_NAND_CTL_SETCLE(nandptr) do { \
switch((unsigned long)nandptr) { \
- case CFG_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CLE); \
+ case CONFIG_SYS_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \
break; \
- case CFG_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_CLE); \
+ case CONFIG_SYS_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \
break; \
} \
} while(0)
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */
+#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
#endif /* No PCI */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFFFC0000
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
+#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
+#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
-#endif
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CFG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */
-#define CFG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/
-#define CFG_ENV_ADDR_REDUND 0xFFFFA000
-#define CFG_ENV_SIZE_REDUND 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */
+#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/
+#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000
+#define CONFIG_ENV_SIZE_REDUND 0x2000
+
+#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
+#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
-/*#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
-#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
/* last 4 bits of the address */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+#define CONFIG_SYS_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */
/* have only 8kB, 16kB is save here */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* ... */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
*/
/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB0AP 0x92015480
+#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
/* Memory Bank 1 (External SRAM) initialization */
/* Since this must replace NOR Flash, we use the same settings for CS0 */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB1AP 0x92015480
+#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */
-#define CFG_EBC_PB2AP 0x92015480
-#define CFG_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB2AP 0x92015480
+#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */
/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x92015480
-#define CFG_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB3AP 0x92015480
+#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */
#ifdef CONFIG_PPCHAMELEON_SMI712
/*
#define CONFIG_CONSOLE_EXTRA_INFO
#define CONFIG_VGA_AS_SINGLE_DEVICE
/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */
-#define CFG_ISA_IO 0xE8000000
-/* see also drivers/videomodes.c */
-#define CFG_DEFAULT_VIDEO_MODE 0x303
+#define CONFIG_SYS_ISA_IO 0xE8000000
+/* see also drivers/video/videomodes.c */
+#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303
#endif
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA internal regs */
-#define CFG_FPGA_MODE 0x00
-#define CFG_FPGA_STATUS 0x02
-#define CFG_FPGA_TS 0x04
-#define CFG_FPGA_TS_LOW 0x06
-#define CFG_FPGA_TS_CAP0 0x10
-#define CFG_FPGA_TS_CAP0_LOW 0x12
-#define CFG_FPGA_TS_CAP1 0x14
-#define CFG_FPGA_TS_CAP1_LOW 0x16
-#define CFG_FPGA_TS_CAP2 0x18
-#define CFG_FPGA_TS_CAP2_LOW 0x1a
-#define CFG_FPGA_TS_CAP3 0x1c
-#define CFG_FPGA_TS_CAP3_LOW 0x1e
+#define CONFIG_SYS_FPGA_MODE 0x00
+#define CONFIG_SYS_FPGA_STATUS 0x02
+#define CONFIG_SYS_FPGA_TS 0x04
+#define CONFIG_SYS_FPGA_TS_LOW 0x06
+#define CONFIG_SYS_FPGA_TS_CAP0 0x10
+#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
+#define CONFIG_SYS_FPGA_TS_CAP1 0x14
+#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
+#define CONFIG_SYS_FPGA_TS_CAP2 0x18
+#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
+#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
+#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
/* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET 0x0001
-#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
-#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
+#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
+#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000
+#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000
/* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0 0x0001
-#define CFG_FPGA_STATUS_DIP1 0x0002
-#define CFG_FPGA_STATUS_DIP2 0x0004
-#define CFG_FPGA_STATUS_FLASH 0x0008
-#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
+#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
+#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
+#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
+#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000
-#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CONFIG_SYS_TEMP_STACK_OCM 1
/* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR 0xF8000000
-#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
* GPIO0[30] - EMAC0 input
* GPIO0[31] - EMAC1 reject packet as output
*/
-#define CFG_GPIO0_OSRH 0x40000550
-#define CFG_GPIO0_OSRL 0x00000110
-#define CFG_GPIO0_ISR1H 0x00000000
-/*#define CFG_GPIO0_ISR1L 0x15555445*/
-#define CFG_GPIO0_ISR1L 0x15555444
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xF7FF8014
+#define CONFIG_SYS_GPIO0_OSRH 0x40000550
+#define CONFIG_SYS_GPIO0_OSRL 0x00000110
+#define CONFIG_SYS_GPIO0_ISR1H 0x00000000
+/*#define CONFIG_SYS_GPIO0_ISR1L 0x15555445*/
+#define CONFIG_SYS_GPIO0_ISR1L 0x15555444
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014
/*
* Internal Definitions
/* Model HI */
#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55
#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55
-#define CFG_OPB_FREQ 55555555
+#define CONFIG_SYS_OPB_FREQ 55555555
/* Model ME */
#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33
#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33
-#define CFG_OPB_FREQ 66666666
+#define CONFIG_SYS_OPB_FREQ 66666666
#else
/* Model BA (default) */
#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33
#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33
-#define CFG_OPB_FREQ 66666666
+#define CONFIG_SYS_OPB_FREQ 66666666
#endif
#endif /* CONFIG_NO_SERIAL_EEPROM */
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#define CONFIG_JFFS2_NAND_DEV 0 /* nand device jffs2 lives on */
-#define CONFIG_JFFS2_NAND_OFF 0 /* start of jffs2 partition */
-#define CONFIG_JFFS2_NAND_SIZE 2*1024*1024 /* size of jffs2 partition */
#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
+/*
+ * JFFS2 partitions
+ *
+ */
+/* No command line, one static partition */
+#undef CONFIG_CMD_MTDPARTS
+#define CONFIG_JFFS2_DEV "nand"
+#define CONFIG_JFFS2_PART_SIZE 0x00200000
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support
+ *
+ * Note: fake mtd_id used, no linux mtd map file
+ */
+/*
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT "nand0=catcenter"
+#define MTDPARTS_DEFAULT "mtdparts=catcenter:2m(nand)"
+*/
+
#endif /* __CONFIG_H */