imx: add imx8x capricorn giedi board

[oweals/u-boot.git] / include / common.h

diff --git a/include/common.h b/include/common.h
index c22eb63501fbf8a57d70447d173bc4d09fe47329..52c02185f40e0ead25d761ed1c685a56de33f74a 100644 (file)
--- a/include/common.h
+++ b/include/common.h
@@ -3,7 +3,7 @@
  * Common header file for U-Boot
  *
  * This file still includes quite a bit of stuff that should be in separate
- * headers like command.h. Please think before adding more things.
+ * headers. Please think before adding more things.
  * Patches to remove things are welcome.
  *
  * (C) Copyright 2000-2009
@@ -15,7 +15,6 @@
 
 #ifndef __ASSEMBLY__           /* put C only stuff in this section */
 
-typedef unsigned char          uchar;
 typedef volatile unsigned long vu_long;
 typedef volatile unsigned short vu_short;
 typedef volatile unsigned char vu_char;
@@ -66,21 +65,6 @@ void hang            (void) __attribute__ ((noreturn));
 
 /* common/main.c */
 void   main_loop       (void);
-int run_command(const char *cmd, int flag);
-int run_command_repeatable(const char *cmd, int flag);
-
-/**
- * Run a list of commands separated by ; or even \0
- *
- * Note that if 'len' is not -1, then the command does not need to be nul
- * terminated, Memory will be allocated for the command in that case.
- *
- * @param cmd  List of commands to run, each separated bu semicolon
- * @param len  Length of commands excluding terminator if known (-1 if not)
- * @param flag Execution flags (CMD_FLAG_...)
- * @return 0 on success, or != 0 on error.
- */
-int run_command_list(const char *cmd, int len, int flag);
 
 int checkflash(void);
 int checkdram(void);
@@ -88,26 +72,6 @@ extern u8 __dtb_dt_begin[];  /* embedded device tree blob */
 extern u8 __dtb_dt_spl_begin[];        /* embedded device tree blob for SPL/TPL */
 int mdm_init(void);
 
-/**
- * Show the DRAM size in a board-specific way
- *
- * This is used by boards to display DRAM information in their own way.
- *
- * @param size Size of DRAM (which should be displayed along with other info)
- */
-void board_show_dram(phys_size_t size);
-
-/**
- * Get the uppermost pointer that is valid to access
- *
- * Some systems may not map all of their address space. This function allows
- * boards to indicate what their highest support pointer value is for DRAM
- * access.
- *
- * @param total_size   Size of U-Boot (unused?)
- */
-ulong board_get_usable_ram_top(ulong total_size);
-
 /**
  * arch_fixup_fdt() - Write arch-specific information to fdt
  *
@@ -137,8 +101,6 @@ int do_fat_fsload(cmd_tbl_t *, int, int, char * const []);
 /* common/cmd_ext2.c */
 int do_ext2load(cmd_tbl_t *, int, int, char * const []);
 
-void   pci_init_board(void);
-
 /* common/exports.c */
 void   jumptable_init(void);
 
@@ -153,32 +115,10 @@ phys_size_t get_effective_memsize(void);
 void   reset_phy     (void);
 void   fdc_hw_init   (void);
 
-/* $(BOARD)/eeprom.c */
-#ifdef CONFIG_CMD_EEPROM
-void eeprom_init  (int bus);
-int  eeprom_read  (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
-int  eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
-#else
-/*
- * Some EEPROM code is depecated because it used the legacy I2C interface. Add
- * some macros here so we don't have to touch every one of those uses
- */
-#define eeprom_init(bus)
-#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
-#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
-#endif
-
 #if !defined(CONFIG_ENV_EEPROM_IS_ON_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
 # define CONFIG_SYS_DEF_EEPROM_ADDR CONFIG_SYS_I2C_EEPROM_ADDR
 #endif
 
-/* $(BOARD)/$(BOARD).c */
-int board_early_init_f (void);
-int board_fix_fdt (void *rw_fdt_blob); /* manipulate the U-Boot fdt before its relocation */
-int board_late_init (void);
-int board_postclk_init (void); /* after clocks/timebase, before env/serial */
-int board_early_init_r (void);
-
 #if defined(CONFIG_SYS_DRAM_TEST)
 int testdram(void);
 #endif /* CONFIG_SYS_DRAM_TEST */
@@ -188,8 +128,6 @@ void        relocate_code(ulong);
 #else
 void   relocate_code(ulong, gd_t *, ulong) __attribute__ ((noreturn));
 #endif
-ulong  get_endaddr   (void);
-void   trap_init     (ulong);
 
 void s_init(void);