+/* SPDX-License-Identifier: GPL-2.0+ */
/*
+ * Common header file for U-Boot
+ *
+ * This file still includes quite a bit of stuff that should be in separate
+ * headers. Please think before adding more things.
+ * Patches to remove things are welcome.
+ *
* (C) Copyright 2000-2009
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __COMMON_H_
#ifndef __ASSEMBLY__ /* put C only stuff in this section */
-typedef unsigned char uchar;
typedef volatile unsigned long vu_long;
typedef volatile unsigned short vu_short;
typedef volatile unsigned char vu_char;
-/* Allow sharing constants with type modifiers between C and assembly. */
-#define _AC(X, Y) (X##Y)
-
#include <config.h>
#include <errno.h>
#include <time.h>
#include <asm-offsets.h>
#include <linux/bitops.h>
+#include <linux/bug.h>
#include <linux/delay.h>
#include <linux/types.h>
+#include <linux/printk.h>
#include <linux/string.h>
#include <linux/stringify.h>
#include <asm/ptrace.h>
#include <flash.h>
#include <image.h>
-/* Bring in printf format macros if inttypes.h is included */
-#define __STDC_FORMAT_MACROS
-
#ifdef __LP64__
#define CONFIG_SYS_SUPPORT_64BIT_DATA
#endif
-#ifdef DEBUG
-#define _DEBUG 1
-#else
-#define _DEBUG 0
-#endif
-
-#ifdef CONFIG_SPL_BUILD
-#define _SPL_BUILD 1
-#else
-#define _SPL_BUILD 0
-#endif
-
-/* Define this at the top of a file to add a prefix to debug messages */
-#ifndef pr_fmt
-#define pr_fmt(fmt) fmt
-#endif
-
-/*
- * Output a debug text when condition "cond" is met. The "cond" should be
- * computed by a preprocessor in the best case, allowing for the best
- * optimization.
- */
-#define debug_cond(cond, fmt, args...) \
- do { \
- if (cond) \
- printf(pr_fmt(fmt), ##args); \
- } while (0)
-
-/* Show a message if DEBUG is defined in a file */
-#define debug(fmt, args...) \
- debug_cond(_DEBUG, fmt, ##args)
-
-/* Show a message if not in SPL */
-#define warn_non_spl(fmt, args...) \
- debug_cond(!_SPL_BUILD, fmt, ##args)
-
-/*
- * An assertion is run-time check done in debug mode only. If DEBUG is not
- * defined then it is skipped. If DEBUG is defined and the assertion fails,
- * then it calls panic*( which may or may not reset/halt U-Boot (see
- * CONFIG_PANIC_HANG), It is hoped that all failing assertions are found
- * before release, and after release it is hoped that they don't matter. But
- * in any case these failing assertions cannot be fixed with a reset (which
- * may just do the same assertion again).
- */
-void __assert_fail(const char *assertion, const char *file, unsigned line,
- const char *function);
-#define assert(x) \
- ({ if (!(x) && _DEBUG) \
- __assert_fail(#x, __FILE__, __LINE__, __func__); })
-
-#define error(fmt, args...) do { \
- printf("ERROR: " pr_fmt(fmt) "\nat %s:%d/%s()\n", \
- ##args, __FILE__, __LINE__, __func__); \
-} while (0)
-
-#ifndef BUG
-#define BUG() do { \
- printf("BUG: failure at %s:%d/%s()!\n", __FILE__, __LINE__, __FUNCTION__); \
- panic("BUG!"); \
-} while (0)
-#define BUG_ON(condition) do { if (unlikely((condition)!=0)) BUG(); } while(0)
-#endif /* BUG */
-
-typedef void (interrupt_handler_t)(void *);
+#include <log.h>
#include <asm/u-boot.h> /* boot information for Linux kernel */
#include <asm/global_data.h> /* global data used for startup functions */
-#if defined(CONFIG_ENV_IS_EMBEDDED)
-#define TOTAL_MALLOC_LEN CONFIG_SYS_MALLOC_LEN
-#elif ( ((CONFIG_ENV_ADDR+CONFIG_ENV_SIZE) < CONFIG_SYS_MONITOR_BASE) || \
- (CONFIG_ENV_ADDR >= (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)) ) || \
- defined(CONFIG_ENV_IS_IN_NVRAM)
-#define TOTAL_MALLOC_LEN (CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE)
-#else
-#define TOTAL_MALLOC_LEN CONFIG_SYS_MALLOC_LEN
-#endif
+/* startup functions, used in:
+ * common/board_f.c
+ * common/init/board_init.c
+ * common/board_r.c
+ * common/board_info.c
+ */
+#include <init.h>
/*
* Function Prototypes
*/
-int dram_init(void);
-
-/**
- * dram_init_banksize() - Set up DRAM bank sizes
- *
- * This can be implemented by boards to set up the DRAM bank information in
- * gd->bd->bi_dram(). It is called just before relocation, after dram_init()
- * is called.
- *
- * If this is not provided, a default implementation will try to set up a
- * single bank. It will do this if CONFIG_NR_DRAM_BANKS and
- * CONFIG_SYS_SDRAM_BASE are set. The bank will have a start address of
- * CONFIG_SYS_SDRAM_BASE and the size will be determined by a call to
- * get_effective_memsize().
- *
- * @return 0 if OK, -ve on error
- */
-int dram_init_banksize(void);
-
void hang (void) __attribute__ ((noreturn));
-int timer_init(void);
-int cpu_init(void);
-
#include <display_options.h>
/* common/main.c */
void main_loop (void);
-int run_command(const char *cmd, int flag);
-int run_command_repeatable(const char *cmd, int flag);
-
-/**
- * Run a list of commands separated by ; or even \0
- *
- * Note that if 'len' is not -1, then the command does not need to be nul
- * terminated, Memory will be allocated for the command in that case.
- *
- * @param cmd List of commands to run, each separated bu semicolon
- * @param len Length of commands excluding terminator if known (-1 if not)
- * @param flag Execution flags (CMD_FLAG_...)
- * @return 0 on success, or != 0 on error.
- */
-int run_command_list(const char *cmd, int len, int flag);
-
-/* arch/$(ARCH)/lib/board.c */
-void board_init_f(ulong);
-void board_init_r(gd_t *, ulong) __attribute__ ((noreturn));
-
-/**
- * ulong board_init_f_alloc_reserve - allocate reserved area
- *
- * This function is called by each architecture very early in the start-up
- * code to allow the C runtime to reserve space on the stack for writable
- * 'globals' such as GD and the malloc arena.
- *
- * @top: top of the reserve area, growing down.
- * @return: bottom of reserved area
- */
-ulong board_init_f_alloc_reserve(ulong top);
-
-/**
- * board_init_f_init_reserve - initialize the reserved area(s)
- *
- * This function is called once the C runtime has allocated the reserved
- * area on the stack. It must initialize the GD at the base of that area.
- *
- * @base: top from which reservation was done
- */
-void board_init_f_init_reserve(ulong base);
-
-/**
- * arch_setup_gd() - Set up the global_data pointer
- *
- * This pointer is special in some architectures and cannot easily be assigned
- * to. For example on x86 it is implemented by adding a specific record to its
- * Global Descriptor Table! So we we provide a function to carry out this task.
- * For most architectures this can simply be:
- *
- * gd = gd_ptr;
- *
- * @gd_ptr: Pointer to global data
- */
-void arch_setup_gd(gd_t *gd_ptr);
-int checkboard(void);
-int show_board_info(void);
int checkflash(void);
int checkdram(void);
-int last_stage_init(void);
-extern ulong monitor_flash_len;
-int mac_read_from_eeprom(void);
extern u8 __dtb_dt_begin[]; /* embedded device tree blob */
-int set_cpu_clk_info(void);
+extern u8 __dtb_dt_spl_begin[]; /* embedded device tree blob for SPL/TPL */
int mdm_init(void);
-int print_cpuinfo(void);
-int update_flash_size(int flash_size);
-int arch_early_init_r(void);
-
-/*
- * setup_board_extra() - Fill in extra details in the bd_t structure
- *
- * @return 0 if OK, -ve on error
- */
-int setup_board_extra(void);
-
-/**
- * arch_fsp_init() - perform firmware support package init
- *
- * Where U-Boot relies on binary blobs to handle part of the system init, this
- * function can be used to set up the blobs. This is used on some Intel
- * platforms.
- */
-int arch_fsp_init(void);
-
-/**
- * arch_cpu_init_dm() - init CPU after driver model is available
- *
- * This is called immediately after driver model is available before
- * relocation. This is similar to arch_cpu_init() but is able to reference
- * devices
- *
- * @return 0 if OK, -ve on error
- */
-int arch_cpu_init_dm(void);
-
-/**
- * Reserve all necessary stacks
- *
- * This is used in generic board init sequence in common/board_f.c. Each
- * architecture could provide this function to tailor the required stacks.
- *
- * On entry gd->start_addr_sp is pointing to the suggested top of the stack.
- * The callee ensures gd->start_add_sp is 16-byte aligned, so architectures
- * require only this can leave it untouched.
- *
- * On exit gd->start_addr_sp and gd->irq_sp should be set to the respective
- * positions of the stack. The stack pointer(s) will be set to this later.
- * gd->irq_sp is only required, if the architecture needs it.
- *
- * @return 0 if no error
- */
-__weak int arch_reserve_stacks(void);
-
-/**
- * Show the DRAM size in a board-specific way
- *
- * This is used by boards to display DRAM information in their own way.
- *
- * @param size Size of DRAM (which should be displayed along with other info)
- */
-void board_show_dram(phys_size_t size);
/**
* arch_fixup_fdt() - Write arch-specific information to fdt
*/
int arch_fixup_fdt(void *blob);
-int reserve_mmu(void);
/* common/flash.c */
void flash_perror (int);
/* common/cmd_ext2.c */
int do_ext2load(cmd_tbl_t *, int, int, char * const []);
-/* common/cmd_nvedit.c */
-int env_init (void);
-void env_relocate (void);
-int envmatch (uchar *, int);
-
-/**
- * env_get() - Look up the value of an environment variable
- *
- * In U-Boot proper this can be called before relocation (which is when the
- * environment is loaded from storage, i.e. GD_FLG_ENV_READY is 0). In that
- * case this function calls env_get_f().
- *
- * @varname: Variable to look up
- * @return value of variable, or NULL if not found
- */
-char *env_get(const char *varname);
-
-/**
- * env_get_f() - Look up the value of an environment variable (early)
- *
- * This function is called from env_get() if the environment has not been
- * loaded yet (GD_FLG_ENV_READY flag is 0). Some environment locations will
- * support reading the value (slowly) and some will not.
- *
- * @varname: Variable to look up
- * @return value of variable, or NULL if not found
- */
-int env_get_f(const char *name, char *buf, unsigned len);
-
-/**
- * env_get_ulong() - Return an environment variable as an integer value
- *
- * Most U-Boot environment variables store hex values. For those which store
- * (e.g.) base-10 integers, this function can be used to read the value.
- *
- * @name: Variable to look up
- * @base: Base to use (e.g. 10 for base 10, 2 for binary)
- * @default_val: Default value to return if no value is found
- * @return the value found, or @default_val if none
- */
-ulong env_get_ulong(const char *name, int base, ulong default_val);
-
-/**
- * env_get_hex() - Return an environment variable as a hex value
- *
- * Decode an environment as a hex number (it may or may not have a 0x
- * prefix). If the environment variable cannot be found, or does not start
- * with hex digits, the default value is returned.
- *
- * @varname: Variable to decode
- * @default_val: Value to return on error
- */
-ulong env_get_hex(const char *varname, ulong default_val);
-
-/*
- * Read an environment variable as a boolean
- * Return -1 if variable does not exist (default to true)
- */
-int env_get_yesno(const char *var);
-
-/**
- * env_set() - set an environment variable
- *
- * This sets or deletes the value of an environment variable. For setting the
- * value the variable is created if it does not already exist.
- *
- * @varname: Variable to adjust
- * @value: Value to set for the variable, or NULL or "" to delete the variable
- * @return 0 if OK, 1 on error
- */
-int env_set(const char *varname, const char *value);
-
-/**
- * env_set_ulong() - set an environment variable to an integer
- *
- * @varname: Variable to adjust
- * @value: Value to set for the variable (will be converted to a string)
- * @return 0 if OK, 1 on error
- */
-int env_set_ulong(const char *varname, ulong value);
-
-/**
- * env_set_hex() - set an environment variable to a hex value
- *
- * @varname: Variable to adjust
- * @value: Value to set for the variable (will be converted to a hex string)
- * @return 0 if OK, 1 on error
- */
-int env_set_hex(const char *varname, ulong value);
-
-/**
- * env_set_addr - Set an environment variable to an address in hex
- *
- * @varname: Environment variable to set
- * @addr: Value to set it to
- * @return 0 if ok, 1 on error
- */
-static inline int env_set_addr(const char *varname, const void *addr)
-{
- return env_set_hex(varname, (ulong)addr);
-}
-
-#ifdef CONFIG_AUTO_COMPLETE
-int env_complete(char *var, int maxv, char *cmdv[], int maxsz, char *buf);
-#endif
-int get_env_id (void);
-
-void pci_init (void);
-void pci_init_board(void);
-
-#if defined(CONFIG_DTB_RESELECT)
-int embedded_dtb_select(void);
-#endif
-
-int misc_init_f (void);
-int misc_init_r (void);
-
/* common/exports.c */
void jumptable_init(void);
void reset_phy (void);
void fdc_hw_init (void);
-/* $(BOARD)/eeprom.c */
-#ifdef CONFIG_CMD_EEPROM
-void eeprom_init (int bus);
-int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
-int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
-#else
-/*
- * Some EEPROM code is depecated because it used the legacy I2C interface. Add
- * some macros here so we don't have to touch every one of those uses
- */
-#define eeprom_init(bus)
-#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
-#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
-#endif
-
-/*
- * Set this up regardless of board
- * type, to prevent errors.
- */
-#if defined(CONFIG_SPI) || !defined(CONFIG_SYS_I2C_EEPROM_ADDR)
-# define CONFIG_SYS_DEF_EEPROM_ADDR 0
-#else
-#if !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
+#if !defined(CONFIG_ENV_EEPROM_IS_ON_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
# define CONFIG_SYS_DEF_EEPROM_ADDR CONFIG_SYS_I2C_EEPROM_ADDR
#endif
-#endif /* CONFIG_SPI || !defined(CONFIG_SYS_I2C_EEPROM_ADDR) */
-
-#if defined(CONFIG_SPI)
-extern void spi_init_f (void);
-extern void spi_init_r (void);
-extern ssize_t spi_read (uchar *, int, uchar *, int);
-extern ssize_t spi_write (uchar *, int, uchar *, int);
-#endif
-
-/* $(BOARD)/$(BOARD).c */
-int board_early_init_f (void);
-int board_fix_fdt (void *rw_fdt_blob); /* manipulate the U-Boot fdt before its relocation */
-int board_late_init (void);
-int board_postclk_init (void); /* after clocks/timebase, before env/serial */
-int board_early_init_r (void);
-void board_poweroff (void);
#if defined(CONFIG_SYS_DRAM_TEST)
int testdram(void);
#endif /* CONFIG_SYS_DRAM_TEST */
-/* $(CPU)/start.S */
-int icache_status (void);
-void icache_enable (void);
-void icache_disable(void);
-int dcache_status (void);
-void dcache_enable (void);
-void dcache_disable(void);
-void mmu_disable(void);
#if defined(CONFIG_ARM)
void relocate_code(ulong);
#else
void relocate_code(ulong, gd_t *, ulong) __attribute__ ((noreturn));
#endif
-ulong get_endaddr (void);
-void trap_init (ulong);
-
-/* $(CPU)/cpu.c */
-static inline int cpumask_next(int cpu, unsigned int mask)
-{
- for (cpu++; !((1 << cpu) & mask); cpu++)
- ;
- return cpu;
-}
+void s_init(void);
-#define for_each_cpu(iter, cpu, num_cpus, mask) \
- for (iter = 0, cpu = cpumask_next(-1, mask); \
- iter < num_cpus; \
- iter++, cpu = cpumask_next(cpu, mask)) \
-
-int cpu_numcores (void);
-int cpu_num_dspcores(void);
-u32 cpu_mask (void);
-u32 cpu_dsp_mask(void);
-int is_core_valid (unsigned int);
-
-/**
- * arch_cpu_init() - basic cpu-dependent setup for an architecture
- *
- * This is called after early malloc is available. It should handle any
- * CPU- or SoC- specific init needed to continue the init sequence. See
- * board_f.c for where it is called. If this is not provided, a default
- * version (which does nothing) will be used.
- */
-int arch_cpu_init(void);
-
-int checkcpu (void);
-int checkicache (void);
-int checkdcache (void);
void upmconfig (unsigned int, unsigned int *, unsigned int);
ulong get_tbclk (void);
void reset_misc (void);
void ft_cpu_setup(void *blob, bd_t *bd);
void ft_pci_setup(void *blob, bd_t *bd);
-void smp_set_core_boot_addr(unsigned long addr, int corenr);
-void smp_kick_all_cpus(void);
-
-/* $(CPU)/serial.c */
-int serial_init (void);
-void serial_setbrg (void);
-void serial_putc (const char);
-void serial_putc_raw(const char);
-void serial_puts (const char *);
-int serial_getc (void);
-int serial_tstc (void);
-
/* $(CPU)/speed.c */
int get_clocks (void);
ulong get_bus_freq (ulong);
int get_serial_clock(void);
-int cpu_init_r (void);
-
-/* $(CPU)/interrupts.c */
-int interrupt_init (void);
-void timer_interrupt (struct pt_regs *);
-void external_interrupt (struct pt_regs *);
-void irq_install_handler(int, interrupt_handler_t *, void *);
-void irq_free_handler (int);
-void reset_timer (void);
-
-/* Return value of monotonic microsecond timer */
-unsigned long timer_get_us(void);
-
-void enable_interrupts (void);
-int disable_interrupts (void);
-
-/* $(CPU)/.../commproc.c */
-int dpram_init (void);
-uint dpram_base(void);
-uint dpram_base_align(uint align);
-uint dpram_alloc(uint size);
-uint dpram_alloc_align(uint size,uint align);
-void bootcount_store (ulong);
-ulong bootcount_load (void);
-#define BOOTCOUNT_MAGIC 0xB001C041
-
-/* $(CPU)/.../<eth> */
-void mii_init (void);
-
-/* $(CPU)/.../lcd.c */
-ulong lcd_setmem (ulong);
-
-/* $(CPU)/.../video.c */
-ulong video_setmem (ulong);
-
-/* arch/$(ARCH)/lib/cache.c */
-void enable_caches(void);
-void flush_cache (unsigned long, unsigned long);
-void flush_dcache_all(void);
-void flush_dcache_range(unsigned long start, unsigned long stop);
-void invalidate_dcache_range(unsigned long start, unsigned long stop);
-void invalidate_dcache_all(void);
-void invalidate_icache_all(void);
-
-enum {
- /* Disable caches (else flush caches but leave them active) */
- CBL_DISABLE_CACHES = 1 << 0,
- CBL_SHOW_BOOTSTAGE_REPORT = 1 << 1,
-
- CBL_ALL = 3,
-};
-
-/**
- * Clean up ready for linux
- *
- * @param flags Flags to control what is done
- */
-int cleanup_before_linux_select(int flags);
-
-/* arch/$(ARCH)/lib/ticks.S */
-uint64_t get_ticks(void);
-void wait_ticks (unsigned long);
-
-/* arch/$(ARCH)/lib/time.c */
-ulong usec2ticks (unsigned long usec);
-ulong ticks2usec (unsigned long ticks);
-
-/* lib/gunzip.c */
-int gunzip(void *, int, unsigned char *, unsigned long *);
-int zunzip(void *dst, int dstlen, unsigned char *src, unsigned long *lenp,
- int stoponerr, int offset);
-
-/**
- * gzwrite progress indicators: defined weak to allow board-specific
- * overrides:
- *
- * gzwrite_progress_init called on startup
- * gzwrite_progress called during decompress/write loop
- * gzwrite_progress_finish called at end of loop to
- * indicate success (retcode=0) or failure
- */
-void gzwrite_progress_init(u64 expected_size);
-
-void gzwrite_progress(int iteration,
- u64 bytes_written,
- u64 total_bytes);
-
-void gzwrite_progress_finish(int retcode,
- u64 totalwritten,
- u64 totalsize,
- u32 expected_crc,
- u32 calculated_crc);
-
-/**
- * decompress and write gzipped image from memory to block device
- *
- * @param src compressed image address
- * @param len compressed image length in bytes
- * @param dev block device descriptor
- * @param szwritebuf bytes per write (pad to erase size)
- * @param startoffs offset in bytes of first write
- * @param szexpected expected uncompressed length
- * may be zero to use gzip trailer
- * for files under 4GiB
- */
-int gzwrite(unsigned char *src, int len,
- struct blk_desc *dev,
- unsigned long szwritebuf,
- u64 startoffs,
- u64 szexpected);
-
-/* lib/lz4_wrapper.c */
-int ulz4fn(const void *src, size_t srcn, void *dst, size_t *dstn);
-
-/* lib/qsort.c */
-void qsort(void *base, size_t nmemb, size_t size,
- int(*compar)(const void *, const void *));
-int strcmp_compar(const void *, const void *);
-
/* lib/uuid.c */
#include <uuid.h>
/* lib/vsprintf.c */
#include <vsprintf.h>
-/* lib/strmhz.c */
-char * strmhz(char *buf, unsigned long hz);
-
-/* lib/crc32.c */
-#include <u-boot/crc.h>
-
-/* lib/rand.c */
-#define RAND_MAX -1U
-void srand(unsigned int seed);
-unsigned int rand(void);
-unsigned int rand_r(unsigned int *seedp);
-
-/*
- * STDIO based functions (can always be used)
- */
-/* serial stuff */
-int serial_printf (const char *fmt, ...)
- __attribute__ ((format (__printf__, 1, 2)));
-
-/* lib/gzip.c */
-int gzip(void *dst, unsigned long *lenp,
- unsigned char *src, unsigned long srclen);
-int zzip(void *dst, unsigned long *lenp, unsigned char *src,
- unsigned long srclen, int stoponerr,
- int (*func)(unsigned long, unsigned long));
-
/* lib/net_utils.c */
#include <net.h>
-static inline struct in_addr env_get_ip(char *var)
-{
- return string_to_ip(env_get(var));
-}
-
-int pcmcia_init (void);
-
-#ifdef CONFIG_LED_STATUS
-# include <status_led.h>
-#endif
#include <bootstage.h>
-#ifdef CONFIG_SHOW_ACTIVITY
-void show_activity(int arg);
-#endif
-
-/* Multicore arch functions */
-#ifdef CONFIG_MP
-int cpu_status(int nr);
-int cpu_reset(int nr);
-int cpu_disable(int nr);
-int cpu_release(int nr, int argc, char * const argv[]);
-#endif
-
#else /* __ASSEMBLY__ */
-/* Drop a C type modifier (like in 3UL) for constants used in assembly. */
-#define _AC(X, Y) X
-
#endif /* __ASSEMBLY__ */
/* Put only stuff here that the assembler can digest */
-/* Declare an unsigned long constant digestable both by C and an assembler. */
-#define UL(x) _AC(x, UL)
-
#ifdef CONFIG_POST
#define CONFIG_HAS_POST
#ifndef CONFIG_POST_ALT_LIST
#endif
#endif
-#ifdef CONFIG_INIT_CRITICAL
-#error CONFIG_INIT_CRITICAL is deprecated!
-#error Read section CONFIG_SKIP_LOWLEVEL_INIT in README.
-#endif
-
#define ROUND(a,b) (((a) + (b) - 1) & ~((b) - 1))
/*
/* Pull in stuff for the build system */
#ifdef DO_DEPS_ONLY
-# include <environment.h>
+# include <env_internal.h>
#endif
#endif /* __COMMON_H_ */