* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
+ *
+ ********************************************************************
+ * NOTE: This header file defines an interface to U-Boot. Including
+ * this (unmodified) header file in another file is considered normal
+ * use of U-Boot, and does *not* fall under the heading of "derived
+ * work".
+ ********************************************************************
*/
#ifndef __U_BOOT_H__
*/
#ifndef __ASSEMBLY__
-#include <linux/types.h>
typedef struct bd_info {
- unsigned long bi_memstart; /* start of DRAM memory */
- unsigned long bi_memsize; /* size of DRAM memory in bytes */
- unsigned long bi_flashstart; /* start of FLASH memory */
- unsigned long bi_flashsize; /* size of FLASH memory */
- unsigned long bi_flashoffset; /* reserved area for startup monitor */
- unsigned long bi_sramstart; /* start of SRAM memory */
- unsigned long bi_sramsize; /* size of SRAM memory */
- unsigned long bi_bootflags; /* boot / reboot flag (for LynxOS) */
- unsigned long bi_boot_params; /* where this board expects params */
- unsigned long bi_ip_addr; /* IP Address */
- unsigned char bi_enetaddr[6]; /* Ethernet adress */
- unsigned short bi_ethspeed; /* Ethernet speed in Mbps */
- unsigned long bi_intfreq; /* Internal Freq, in MHz */
- unsigned long bi_busfreq; /* Bus Freq, in MHz */
- unsigned long bi_baudrate; /* Console Baudrate */
-} bd_t;
+ unsigned long bi_memstart; /* start of DRAM memory */
+ phys_size_t bi_memsize; /* size of DRAM memory in bytes */
+ unsigned long bi_flashstart; /* start of FLASH memory */
+ unsigned long bi_flashsize; /* size of FLASH memory */
+ unsigned long bi_flashoffset; /* reserved area for startup monitor */
+ unsigned long bi_sramstart; /* start of SRAM memory */
+ unsigned long bi_sramsize; /* size of SRAM memory */
+ unsigned long bi_mbar_base; /* base of internal registers */
+ unsigned long bi_bootflags; /* boot / reboot flag (for LynxOS) */
+ unsigned long bi_boot_params; /* where this board expects params */
+ unsigned long bi_ip_addr; /* IP Address */
+ unsigned char bi_enetaddr[6]; /* Ethernet adress */
+ unsigned short bi_ethspeed; /* Ethernet speed in Mbps */
+ unsigned long bi_intfreq; /* Internal Freq, in MHz */
+ unsigned long bi_busfreq; /* Bus Freq, in MHz */
+#ifdef CONFIG_PCI
+ unsigned long bi_pcifreq; /* pci Freq in MHz */
+#endif
+#ifdef CONFIG_EXTRA_CLOCK
+ unsigned long bi_inpfreq; /* input Freq in MHz */
+ unsigned long bi_vcofreq; /* vco Freq in MHz */
+ unsigned long bi_flbfreq; /* Flexbus Freq in MHz */
+#endif
+ unsigned long bi_baudrate; /* Console Baudrate */
-#endif /* __ASSEMBLY__ */
-/* The following data structure is placed in DPRAM to allow for a
- * minimum set of global variables during system initialization
- * (until we have set up the memory controller so that we can use
- * RAM).
- *
- * Keep it *SMALL* and remember to set CFG_INIT_DATA_SIZE > sizeof(init_data_t)
- */
-typedef struct init_data {
- unsigned long cpu_clk; /* VCOOUT = CPU clock in Hz! */
- unsigned long env_addr; /* Address of Environment struct */
- unsigned long env_valid; /* Checksum of Environment valid? */
- unsigned long relocated; /* Relocat. offset when running in RAM */
- unsigned long have_console; /* serial_init() was called */
-#ifdef CONFIG_LCD
- unsigned long lcd_base; /* Base address of LCD frambuffer mem */
+#ifdef CONFIG_HAS_ETH1
+ /* second onboard ethernet port */
+ unsigned char bi_enet1addr[6];
#endif
-} init_data_t;
-#endif /* __U_BOOT_H__ */
+#ifdef CONFIG_HAS_ETH2
+ /* third onboard ethernet port */
+ unsigned char bi_enet2addr[6];
+#endif
+#ifdef CONFIG_HAS_ETH3
+ unsigned char bi_enet3addr[6];
+#endif
+} bd_t;
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* __U_BOOT_H__ */