#include <fdtdec.h>
#include <malloc.h>
#include <spi.h>
-#include <asm/errno.h>
+#include <linux/errno.h>
#include "cadence_qspi.h"
#define CQSPI_STIG_READ 0
}
/* Calibration sequence to determine the read data capture delay register */
-static int spi_calibration(struct udevice *bus)
+static int spi_calibration(struct udevice *bus, uint hz)
{
- struct cadence_spi_platdata *plat = bus->platdata;
struct cadence_spi_priv *priv = dev_get_priv(bus);
void *base = priv->regbase;
u8 opcode_rdid = 0x9F;
}
/* use back the intended clock and find low range */
- cadence_spi_write_speed(bus, plat->max_hz);
+ cadence_spi_write_speed(bus, hz);
for (i = 0; i < CQSPI_READ_CAPTURE_MAX_DELAY; i++) {
/* Disable QSPI */
cadence_qspi_apb_controller_disable(base);
(range_hi + range_lo) / 2, range_lo, range_hi);
/* just to ensure we do once only when speed or chip select change */
- priv->qspi_calibrated_hz = plat->max_hz;
+ priv->qspi_calibrated_hz = hz;
priv->qspi_calibrated_cs = spi_chip_select(bus);
return 0;
struct cadence_spi_priv *priv = dev_get_priv(bus);
int err;
+ if (hz > plat->max_hz)
+ hz = plat->max_hz;
+
/* Disable QSPI */
cadence_qspi_apb_controller_disable(priv->regbase);
- cadence_spi_write_speed(bus, hz);
-
- /* Calibration required for different SCLK speed or chip select */
- if (priv->qspi_calibrated_hz != plat->max_hz ||
+ /*
+ * Calibration required for different current SCLK speed, requested
+ * SCLK speed or chip select
+ */
+ if (priv->previous_hz != hz ||
+ priv->qspi_calibrated_hz != hz ||
priv->qspi_calibrated_cs != spi_chip_select(bus)) {
- err = spi_calibration(bus);
+ err = spi_calibration(bus, hz);
if (err)
return err;
+
+ /* prevent calibration run when same as previous request */
+ priv->previous_hz = hz;
}
/* Enable QSPI */
static int cadence_spi_set_mode(struct udevice *bus, uint mode)
{
struct cadence_spi_priv *priv = dev_get_priv(bus);
- unsigned int clk_pol = (mode & SPI_CPOL) ? 1 : 0;
- unsigned int clk_pha = (mode & SPI_CPHA) ? 1 : 0;
/* Disable QSPI */
cadence_qspi_apb_controller_disable(priv->regbase);
/* Set SPI mode */
- cadence_qspi_apb_set_clk_mode(priv->regbase, clk_pol, clk_pha);
+ cadence_qspi_apb_set_clk_mode(priv->regbase, mode);
/* Enable QSPI */
cadence_qspi_apb_controller_enable(priv->regbase);
struct udevice *bus = dev->parent;
struct cadence_spi_platdata *plat = bus->platdata;
struct cadence_spi_priv *priv = dev_get_priv(bus);
+ struct dm_spi_slave_platdata *dm_plat = dev_get_parent_platdata(dev);
void *base = priv->regbase;
u8 *cmd_buf = priv->cmd_buf;
size_t data_bytes;
break;
case CQSPI_INDIRECT_READ:
err = cadence_qspi_apb_indirect_read_setup(plat,
- priv->cmd_len, cmd_buf);
+ priv->cmd_len, dm_plat->mode, cmd_buf);
if (!err) {
err = cadence_qspi_apb_indirect_read_execute
(plat, data_bytes, din);
{
struct cadence_spi_platdata *plat = bus->platdata;
const void *blob = gd->fdt_blob;
- int node = bus->of_offset;
+ int node = dev_of_offset(bus);
int subnode;
u32 data[4];
int ret;
plat->regbase = (void *)data[0];
plat->ahbbase = (void *)data[2];
-
- /* Use 500KHz as a suitable default */
- plat->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency",
- 500000);
+ plat->sram_size = fdtdec_get_int(blob, node, "sram-size", 128);
/* All other paramters are embedded in the child node */
subnode = fdt_first_subnode(blob, node);
return -ENODEV;
}
+ /* Use 500 KHz as a suitable default */
+ plat->max_hz = fdtdec_get_uint(blob, subnode, "spi-max-frequency",
+ 500000);
+
/* Read other parameters from DT */
plat->page_size = fdtdec_get_int(blob, subnode, "page-size", 256);
plat->block_size = fdtdec_get_int(blob, subnode, "block-size", 16);
plat->tsd2d_ns = fdtdec_get_int(blob, subnode, "tsd2d-ns", 255);
plat->tchsh_ns = fdtdec_get_int(blob, subnode, "tchsh-ns", 20);
plat->tslch_ns = fdtdec_get_int(blob, subnode, "tslch-ns", 20);
- plat->sram_size = fdtdec_get_int(blob, node, "sram-size", 128);
debug("%s: regbase=%p ahbbase=%p max-frequency=%d page-size=%d\n",
__func__, plat->regbase, plat->ahbbase, plat->max_hz,