#include <common.h>
#include <clk.h>
#include <dm.h>
+#include <reset.h>
#include <serial.h>
#include <watchdog.h>
#include <asm/io.h>
return 0;
}
-static int stm32_serial_setparity(struct udevice *dev, enum serial_par parity)
+static int stm32_serial_setconfig(struct udevice *dev, uint serial_config)
{
struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
bool stm32f4 = plat->uart_info->stm32f4;
u8 uart_enable_bit = plat->uart_info->uart_enable_bit;
u32 cr1 = plat->base + CR1_OFFSET(stm32f4);
u32 config = 0;
-
- if (stm32f4)
- return -EINVAL; /* not supported in driver*/
+ uint parity = SERIAL_GET_PARITY(serial_config);
+ uint bits = SERIAL_GET_BITS(serial_config);
+ uint stop = SERIAL_GET_STOP(serial_config);
+
+ /*
+ * only parity config is implemented, check if other serial settings
+ * are the default one.
+ * (STM32F4 serial IP didn't support parity setting)
+ */
+ if (bits != SERIAL_8_BITS || stop != SERIAL_ONE_STOP || stm32f4)
+ return -ENOTSUPP; /* not supported in driver*/
clrbits_le32(cr1, USART_CR1_RE | USART_CR1_TE | BIT(uart_enable_bit));
/* update usart configuration (uart need to be disable)
- * PCE: parity check control
+ * PCE: parity check enable
* PS : '0' : Even / '1' : Odd
* M[1:0] = '00' : 8 Data bits
* M[1:0] = '01' : 9 Data bits with parity
config = USART_CR1_PCE | USART_CR1_M0;
break;
}
+
clrsetbits_le32(cr1,
USART_CR1_PCE | USART_CR1_PS | USART_CR1_M1 |
USART_CR1_M0,
{
struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
struct clk clk;
+ struct reset_ctl reset;
int ret;
plat->uart_info = (struct stm32_uart_info *)dev_get_driver_data(dev);
return ret;
}
+ ret = reset_get_by_index(dev, 0, &reset);
+ if (!ret) {
+ reset_assert(&reset);
+ udelay(2);
+ reset_deassert(&reset);
+ }
+
plat->clock_rate = clk_get_rate(&clk);
if (plat->clock_rate < 0) {
clk_disable(&clk);
.pending = stm32_serial_pending,
.getc = stm32_serial_getc,
.setbrg = stm32_serial_setbrg,
- .setparity = stm32_serial_setparity
+ .setconfig = stm32_serial_setconfig
};
U_BOOT_DRIVER(serial_stm32) = {
.platdata_auto_alloc_size = sizeof(struct stm32x7_serial_platdata),
.ops = &stm32_serial_ops,
.probe = stm32_serial_probe,
+#if !CONFIG_IS_ENABLED(OF_CONTROL)
.flags = DM_FLAG_PRE_RELOC,
+#endif
};
#ifdef CONFIG_DEBUG_UART_STM32
_stm32_serial_setbrg(base, uart_info,
CONFIG_DEBUG_UART_CLOCK,
CONFIG_BAUDRATE);
- printf("DEBUG done\n");
}
static inline void _debug_uart_putc(int c)
struct stm32_uart_info *uart_info = _debug_uart_info();
while (_stm32_serial_putc(base, uart_info, c) == -EAGAIN)
- WATCHDOG_RESET();
+ ;
}
DEBUG_UART_FUNCS