#error "CONFIG_MII has to be defined!"
#endif
+#ifndef CONFIG_FEC_XCV_TYPE
+#define CONFIG_FEC_XCV_TYPE MII100
+#endif
+
+/*
+ * The i.MX28 operates with packets in big endian. We need to swap them before
+ * sending and after receiving.
+ */
+#ifdef CONFIG_MX28
+#define CONFIG_FEC_MXC_SWAP_PACKET
+#endif
+
#undef DEBUG
struct nbuf {
uint8_t head[16]; /**< MAC header(6 + 6 + 2) + 2(aligned) */
};
-struct fec_priv gfec = {
- .eth = (struct ethernet_regs *)IMX_FEC_BASE,
- .xcv_type = MII100,
- .rbd_base = NULL,
- .rbd_index = 0,
- .tbd_base = NULL,
- .tbd_index = 0,
- .bd = NULL,
- .rdb_ptr = NULL,
- .base_ptr = NULL,
-};
+#ifdef CONFIG_FEC_MXC_SWAP_PACKET
+static void swap_packet(uint32_t *packet, int length)
+{
+ int i;
+
+ for (i = 0; i < DIV_ROUND_UP(length, 4); i++)
+ packet[i] = __swab32(packet[i]);
+}
+#endif
+
+/*
+ * The i.MX28 has two ethernet interfaces, but they are not equal.
+ * Only the first one can access the MDIO bus.
+ */
+#ifdef CONFIG_MX28
+static inline struct ethernet_regs *fec_miiphy_fec_to_eth(struct fec_priv *fec)
+{
+ return (struct ethernet_regs *)MXS_ENET0_BASE;
+}
+#else
+static inline struct ethernet_regs *fec_miiphy_fec_to_eth(struct fec_priv *fec)
+{
+ return fec->eth;
+}
+#endif
/*
* MII-interface related functions
*/
-static int fec_miiphy_read(char *dev, uint8_t phyAddr, uint8_t regAddr,
+static int fec_miiphy_read(const char *dev, uint8_t phyAddr, uint8_t regAddr,
uint16_t *retVal)
{
struct eth_device *edev = eth_get_dev_by_name(dev);
struct fec_priv *fec = (struct fec_priv *)edev->priv;
+ struct ethernet_regs *eth = fec_miiphy_fec_to_eth(fec);
uint32_t reg; /* convenient holder for the PHY register */
uint32_t phy; /* convenient holder for the PHY */
* reading from any PHY's register is done by properly
* programming the FEC's MII data register.
*/
- writel(FEC_IEVENT_MII, &fec->eth->ievent);
+ writel(FEC_IEVENT_MII, ð->ievent);
reg = regAddr << FEC_MII_DATA_RA_SHIFT;
phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
writel(FEC_MII_DATA_ST | FEC_MII_DATA_OP_RD | FEC_MII_DATA_TA |
- phy | reg, &fec->eth->mii_data);
+ phy | reg, ð->mii_data);
/*
* wait for the related interrupt
*/
- start = get_timer_masked();
- while (!(readl(&fec->eth->ievent) & FEC_IEVENT_MII)) {
+ start = get_timer(0);
+ while (!(readl(ð->ievent) & FEC_IEVENT_MII)) {
if (get_timer(start) > (CONFIG_SYS_HZ / 1000)) {
printf("Read MDIO failed...\n");
return -1;
/*
* clear mii interrupt bit
*/
- writel(FEC_IEVENT_MII, &fec->eth->ievent);
+ writel(FEC_IEVENT_MII, ð->ievent);
/*
* it's now safe to read the PHY's register
*/
- *retVal = readl(&fec->eth->mii_data);
+ *retVal = readl(ð->mii_data);
debug("fec_miiphy_read: phy: %02x reg:%02x val:%#x\n", phyAddr,
regAddr, *retVal);
return 0;
}
-static int fec_miiphy_write(char *dev, uint8_t phyAddr, uint8_t regAddr,
+static void fec_mii_setspeed(struct fec_priv *fec)
+{
+ /*
+ * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
+ * and do not drop the Preamble.
+ */
+ writel((((imx_get_fecclk() / 1000000) + 2) / 5) << 1,
+ &fec->eth->mii_speed);
+ debug("fec_init: mii_speed %08x\n",
+ readl(&fec->eth->mii_speed));
+}
+static int fec_miiphy_write(const char *dev, uint8_t phyAddr, uint8_t regAddr,
uint16_t data)
{
struct eth_device *edev = eth_get_dev_by_name(dev);
struct fec_priv *fec = (struct fec_priv *)edev->priv;
+ struct ethernet_regs *eth = fec_miiphy_fec_to_eth(fec);
uint32_t reg; /* convenient holder for the PHY register */
uint32_t phy; /* convenient holder for the PHY */
phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
writel(FEC_MII_DATA_ST | FEC_MII_DATA_OP_WR |
- FEC_MII_DATA_TA | phy | reg | data, &fec->eth->mii_data);
+ FEC_MII_DATA_TA | phy | reg | data, ð->mii_data);
/*
* wait for the MII interrupt
*/
- start = get_timer_masked();
- while (!(readl(&fec->eth->ievent) & FEC_IEVENT_MII)) {
+ start = get_timer(0);
+ while (!(readl(ð->ievent) & FEC_IEVENT_MII)) {
if (get_timer(start) > (CONFIG_SYS_HZ / 1000)) {
printf("Write MDIO failed...\n");
return -1;
/*
* clear MII interrupt bit
*/
- writel(FEC_IEVENT_MII, &fec->eth->ievent);
+ writel(FEC_IEVENT_MII, ð->ievent);
debug("fec_miiphy_write: phy: %02x reg:%02x val:%#x\n", phyAddr,
regAddr, data);
static int miiphy_restart_aneg(struct eth_device *dev)
{
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
+ int ret = 0;
+
/*
* Wake up from sleep if necessary
* Reset PHY, then delay 300ns
*/
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_MIPGSR, 0x00FF);
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_BMCR,
- PHY_BMCR_RESET);
+#ifdef CONFIG_MX27
+ miiphy_write(dev->name, fec->phy_id, MII_DCOUNTER, 0x00FF);
+#endif
+ miiphy_write(dev->name, fec->phy_id, MII_BMCR,
+ BMCR_RESET);
udelay(1000);
/*
* Set the auto-negotiation advertisement register bits
*/
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_ANAR,
- PHY_ANLPAR_TXFD | PHY_ANLPAR_TX | PHY_ANLPAR_10FD |
- PHY_ANLPAR_10 | PHY_ANLPAR_PSB_802_3);
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_BMCR,
- PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
+ miiphy_write(dev->name, fec->phy_id, MII_ADVERTISE,
+ LPA_100FULL | LPA_100HALF | LPA_10FULL |
+ LPA_10HALF | PHY_ANLPAR_PSB_802_3);
+ miiphy_write(dev->name, fec->phy_id, MII_BMCR,
+ BMCR_ANENABLE | BMCR_ANRESTART);
- return 0;
+ if (fec->mii_postcall)
+ ret = fec->mii_postcall(fec->phy_id);
+
+ return ret;
}
static int miiphy_wait_aneg(struct eth_device *dev)
{
uint32_t start;
uint16_t status;
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
/*
* Wait for AN completion
*/
- start = get_timer_masked();
+ start = get_timer(0);
do {
if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
printf("%s: Autonegotiation timeout\n", dev->name);
return -1;
}
- if (miiphy_read(dev->name, CONFIG_FEC_MXC_PHYADDR,
- PHY_BMSR, &status)) {
+ if (miiphy_read(dev->name, fec->phy_id,
+ MII_BMSR, &status)) {
printf("%s: Autonegotiation failed. status: 0x%04x\n",
dev->name, status);
return -1;
}
- } while (!(status & PHY_BMSR_LS));
+ } while (!(status & BMSR_LSTATUS));
return 0;
}
fec->rdb_ptr = malloc(size * count + DB_DATA_ALIGNMENT);
p = (uint32_t)fec->rdb_ptr;
if (!p) {
- puts("fec_imx27: not enough malloc memory!\n");
+ puts("fec_mxc: not enough malloc memory\n");
return -ENOMEM;
}
memset((void *)p, 0, size * count + DB_DATA_ALIGNMENT);
static int fec_get_hwaddr(struct eth_device *dev, unsigned char *mac)
{
- struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
- int i;
-
- for (i = 0; i < 6; i++)
- mac[6-1-i] = readl(&iim->iim_bank_area0[IIM0_MAC + i]);
-
- return is_valid_ether_addr(mac);
+ imx_get_mac_from_fuse(mac);
+ return !is_valid_ether_addr(mac);
}
-static int fec_set_hwaddr(struct eth_device *dev, unsigned char *mac)
+static int fec_set_hwaddr(struct eth_device *dev)
{
+ uchar *mac = dev->enetaddr;
struct fec_priv *fec = (struct fec_priv *)dev->priv;
writel(0, &fec->eth->iaddr1);
/*
* Enable FEC-Lite controller
*/
- writel(FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl);
+ writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN,
+ &fec->eth->ecntrl);
+#if defined(CONFIG_MX25) || defined(CONFIG_MX53)
+ udelay(100);
+ /*
+ * setup the MII gasket for RMII mode
+ */
+
+ /* disable the gasket */
+ writew(0, &fec->eth->miigsk_enr);
+
+ /* wait for the gasket to be disabled */
+ while (readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY)
+ udelay(2);
+
+ /* configure gasket for RMII, 50 MHz, no loopback, and no echo */
+ writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr);
+
+ /* re-enable the gasket */
+ writew(MIIGSK_ENR_EN, &fec->eth->miigsk_enr);
+
+ /* wait until MII gasket is ready */
+ int max_loops = 10;
+ while ((readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) == 0) {
+ if (--max_loops <= 0) {
+ printf("WAIT for MII Gasket ready timed out\n");
+ break;
+ }
+ }
+#endif
miiphy_wait_aneg(edev);
- miiphy_speed(edev->name, CONFIG_FEC_MXC_PHYADDR);
- miiphy_duplex(edev->name, CONFIG_FEC_MXC_PHYADDR);
+ miiphy_speed(edev->name, fec->phy_id);
+ miiphy_duplex(edev->name, fec->phy_id);
/*
* Enable SmartDMA receive task
{
uint32_t base;
struct fec_priv *fec = (struct fec_priv *)dev->priv;
+ uint32_t mib_ptr = (uint32_t)&fec->eth->rmon_t_drop;
+ uint32_t rcntrl;
+ int i;
+
+ /* Initialize MAC address */
+ fec_set_hwaddr(dev);
/*
* reserve memory for both buffer descriptor chains at once
sizeof(struct fec_bd) + DB_ALIGNMENT);
base = (uint32_t)fec->base_ptr;
if (!base) {
- puts("fec_imx27: not enough malloc memory!\n");
+ puts("fec_mxc: not enough malloc memory\n");
return -ENOMEM;
}
memset((void *)base, 0, (2 + FEC_RBD_NUM) *
/*
* Set FEC-Lite receive control register(R_CNTRL):
*/
- if (fec->xcv_type == SEVENWIRE) {
- /*
- * Frame length=1518; 7-wire mode
- */
- writel(0x05ee0020, &fec->eth->r_cntrl); /* FIXME 0x05ee0000 */
- } else {
- /*
- * Frame length=1518; MII mode;
- */
- writel(0x05ee0024, &fec->eth->r_cntrl); /* FIXME 0x05ee0004 */
- /*
- * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
- * and do not drop the Preamble.
- */
- writel((((imx_get_ahbclk() / 1000000) + 2) / 5) << 1,
- &fec->eth->mii_speed);
- debug("fec_init: mii_speed %#lx\n",
- (((imx_get_ahbclk() / 1000000) + 2) / 5) << 1);
- }
+
+ /* Start with frame length = 1518, common for all modes. */
+ rcntrl = PKTSIZE << FEC_RCNTRL_MAX_FL_SHIFT;
+ if (fec->xcv_type == SEVENWIRE)
+ rcntrl |= FEC_RCNTRL_FCE;
+ else if (fec->xcv_type == RMII)
+ rcntrl |= FEC_RCNTRL_RMII;
+ else /* MII mode */
+ rcntrl |= FEC_RCNTRL_FCE | FEC_RCNTRL_MII_MODE;
+
+ writel(rcntrl, &fec->eth->r_cntrl);
+
+ if (fec->xcv_type == MII10 || fec->xcv_type == MII100)
+ fec_mii_setspeed(fec);
+
/*
* Set Opcode/Pause Duration Register
*/
/* clear MIB RAM */
- long *mib_ptr = (long *)(IMX_FEC_BASE + 0x200);
- while (mib_ptr <= (long *)(IMX_FEC_BASE + 0x2FC))
- *mib_ptr++ = 0;
+ for (i = mib_ptr; i <= mib_ptr + 0xfc; i += 4)
+ writel(0, i);
/* FIFO receive start register */
writel(0x520, &fec->eth->r_fstart);
*/
static void fec_halt(struct eth_device *dev)
{
- struct fec_priv *fec = &gfec;
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
int counter = 0xffff;
/*
* issue graceful stop command to the FEC transmitter if necessary
*/
- writel(FEC_ECNTRL_RESET | readl(&fec->eth->x_cntrl),
+ writel(FEC_TCNTRL_GTS | readl(&fec->eth->x_cntrl),
&fec->eth->x_cntrl);
debug("eth_halt: wait for stop regs\n");
* wait for graceful stop to register
*/
while ((counter--) && (!(readl(&fec->eth->ievent) & FEC_IEVENT_GRA)))
- ; /* FIXME ensure time */
+ udelay(1);
/*
* Disable SmartDMA tasks
* Disable the Ethernet Controller
* Note: this will also reset the BD index counter!
*/
- writel(0, &fec->eth->ecntrl);
+ writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN,
+ &fec->eth->ecntrl);
fec->rbd_index = 0;
fec->tbd_index = 0;
debug("eth_halt: done\n");
* Check for valid length of data.
*/
if ((length > 1500) || (length <= 0)) {
- printf("Payload (%d) to large!\n", length);
+ printf("Payload (%d) too large\n", length);
return -1;
}
* Note: We are always using the first buffer for transmission,
* the second will be empty and only used to stop the DMA engine
*/
+#ifdef CONFIG_FEC_MXC_SWAP_PACKET
+ swap_packet((uint32_t *)packet, length);
+#endif
writew(length, &fec->tbd_base[fec->tbd_index].data_length);
writel((uint32_t)packet, &fec->tbd_base[fec->tbd_index].data_pointer);
/*
* wait until frame is sent .
*/
while (readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY) {
- /* FIXME: Timeout */
+ udelay(1);
}
debug("fec_send: status 0x%x index %d\n",
readw(&fec->tbd_base[fec->tbd_index].status),
*/
ievent = readl(&fec->eth->ievent);
writel(ievent, &fec->eth->ievent);
- debug("fec_recv: ievent 0x%x\n", ievent);
+ debug("fec_recv: ievent 0x%lx\n", ievent);
if (ievent & FEC_IEVENT_BABR) {
fec_halt(dev);
fec_init(dev, fec->bd);
/*
* Fill the buffer and pass it to upper layers
*/
+#ifdef CONFIG_FEC_MXC_SWAP_PACKET
+ swap_packet((uint32_t *)frame->data, frame_length);
+#endif
memcpy(buff, frame->data, frame_length);
NetReceive(buff, frame_length);
len = frame_length;
return len;
}
-static int fec_probe(bd_t *bd)
+static int fec_probe(bd_t *bd, int dev_id, int phy_id, uint32_t base_addr)
{
- struct pll_regs *pll = (struct pll_regs *)IMX_PLL_BASE;
struct eth_device *edev;
- struct fec_priv *fec = &gfec;
- unsigned char ethaddr_str[20];
+ struct fec_priv *fec;
unsigned char ethaddr[6];
- char *tmp = getenv("ethaddr");
- char *end;
-
- /* enable FEC clock */
- writel(readl(&pll->pccr1) | PCCR1_HCLK_FEC, &pll->pccr1);
- writel(readl(&pll->pccr0) | PCCR0_FEC_EN, &pll->pccr0);
+ uint32_t start;
+ int ret = 0;
/* create and fill edev struct */
edev = (struct eth_device *)malloc(sizeof(struct eth_device));
if (!edev) {
- puts("fec_imx27: not enough malloc memory!\n");
- return -ENOMEM;
+ puts("fec_mxc: not enough malloc memory for eth_device\n");
+ ret = -ENOMEM;
+ goto err1;
}
+
+ fec = (struct fec_priv *)malloc(sizeof(struct fec_priv));
+ if (!fec) {
+ puts("fec_mxc: not enough malloc memory for fec_priv\n");
+ ret = -ENOMEM;
+ goto err2;
+ }
+
+ memset(edev, 0, sizeof(*edev));
+ memset(fec, 0, sizeof(*fec));
+
edev->priv = fec;
edev->init = fec_init;
edev->send = fec_send;
edev->recv = fec_recv;
edev->halt = fec_halt;
+ edev->write_hwaddr = fec_set_hwaddr;
- fec->eth = (struct ethernet_regs *)IMX_FEC_BASE;
+ fec->eth = (struct ethernet_regs *)base_addr;
fec->bd = bd;
- fec->xcv_type = MII100;
+ fec->xcv_type = CONFIG_FEC_XCV_TYPE;
/* Reset chip. */
- writel(FEC_ECNTRL_RESET, &fec->eth->ecntrl);
- while (readl(&fec->eth->ecntrl) & 1)
+ writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_RESET, &fec->eth->ecntrl);
+ start = get_timer(0);
+ while (readl(&fec->eth->ecntrl) & FEC_ECNTRL_RESET) {
+ if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
+ printf("FEC MXC: Timeout reseting chip\n");
+ goto err3;
+ }
udelay(10);
+ }
/*
* Set interrupt mask register
/*
* Frame length=1518; MII mode;
*/
- writel(0x05ee0024, &fec->eth->r_cntrl); /* FIXME 0x05ee0004 */
- /*
- * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
- * and do not drop the Preamble.
- */
- writel((((imx_get_ahbclk() / 1000000) + 2) / 5) << 1,
- &fec->eth->mii_speed);
- debug("fec_init: mii_speed %#lx\n",
- (((imx_get_ahbclk() / 1000000) + 2) / 5) << 1);
+ writel((PKTSIZE << FEC_RCNTRL_MAX_FL_SHIFT) | FEC_RCNTRL_FCE |
+ FEC_RCNTRL_MII_MODE, &fec->eth->r_cntrl);
+ fec_mii_setspeed(fec);
- sprintf(edev->name, "FEC_MXC");
+ if (dev_id == -1) {
+ sprintf(edev->name, "FEC");
+ fec->dev_id = 0;
+ } else {
+ sprintf(edev->name, "FEC%i", dev_id);
+ fec->dev_id = dev_id;
+ }
+ fec->phy_id = phy_id;
miiphy_register(edev->name, fec_miiphy_read, fec_miiphy_write);
eth_register(edev);
- if ((NULL != tmp) && (12 <= strlen(tmp))) {
- int i;
- /* convert MAC from string to int */
- for (i = 0; i < 6; i++) {
- ethaddr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0;
- if (tmp)
- tmp = (*end) ? end + 1 : end;
- }
- } else if (fec_get_hwaddr(edev, ethaddr) == 0) {
- printf("got MAC address from EEPROM: %pM\n", ethaddr);
- setenv("ethaddr", (char *)ethaddr_str);
+ if (fec_get_hwaddr(edev, ethaddr) == 0) {
+ debug("got MAC address from fuse: %pM\n", ethaddr);
+ memcpy(edev->enetaddr, ethaddr, 6);
}
- memcpy(edev->enetaddr, ethaddr, 6);
- fec_set_hwaddr(edev, ethaddr);
- return 0;
+ return ret;
+
+err3:
+ free(fec);
+err2:
+ free(edev);
+err1:
+ return ret;
}
+#ifndef CONFIG_FEC_MXC_MULTI
int fecmxc_initialize(bd_t *bd)
{
int lout = 1;
debug("eth_init: fec_probe(bd)\n");
- lout = fec_probe(bd);
+ lout = fec_probe(bd, -1, CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+
+ return lout;
+}
+#endif
+
+int fecmxc_initialize_multi(bd_t *bd, int dev_id, int phy_id, uint32_t addr)
+{
+ int lout = 1;
+
+ debug("eth_init: fec_probe(bd, %i, %i) @ %08x\n", dev_id, phy_id, addr);
+ lout = fec_probe(bd, dev_id, phy_id, addr);
return lout;
}
+
+int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int))
+{
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
+ fec->mii_postcall = cb;
+ return 0;
+}