/*
* MII-interface related functions
*/
-static int fec_miiphy_read(char *dev, uint8_t phyAddr, uint8_t regAddr,
+static int fec_miiphy_read(const char *dev, uint8_t phyAddr, uint8_t regAddr,
uint16_t *retVal)
{
struct eth_device *edev = eth_get_dev_by_name(dev);
debug("fec_init: mii_speed %#lx\n",
fec->eth->mii_speed);
}
-static int fec_miiphy_write(char *dev, uint8_t phyAddr, uint8_t regAddr,
+static int fec_miiphy_write(const char *dev, uint8_t phyAddr, uint8_t regAddr,
uint16_t data)
{
struct eth_device *edev = eth_get_dev_by_name(dev);
* Wake up from sleep if necessary
* Reset PHY, then delay 300ns
*/
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_MIPGSR, 0x00FF);
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_BMCR,
- PHY_BMCR_RESET);
+#ifdef CONFIG_MX27
+ miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, MII_DCOUNTER, 0x00FF);
+#endif
+ miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, MII_BMCR,
+ BMCR_RESET);
udelay(1000);
/*
* Set the auto-negotiation advertisement register bits
*/
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_ANAR,
- PHY_ANLPAR_TXFD | PHY_ANLPAR_TX | PHY_ANLPAR_10FD |
- PHY_ANLPAR_10 | PHY_ANLPAR_PSB_802_3);
- miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, PHY_BMCR,
- PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
+ miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, MII_ADVERTISE,
+ LPA_100FULL | LPA_100HALF | LPA_10FULL |
+ LPA_10HALF | PHY_ANLPAR_PSB_802_3);
+ miiphy_write(dev->name, CONFIG_FEC_MXC_PHYADDR, MII_BMCR,
+ BMCR_ANENABLE | BMCR_ANRESTART);
return 0;
}
}
if (miiphy_read(dev->name, CONFIG_FEC_MXC_PHYADDR,
- PHY_BMSR, &status)) {
+ MII_BMSR, &status)) {
printf("%s: Autonegotiation failed. status: 0x%04x\n",
dev->name, status);
return -1;
}
- } while (!(status & PHY_BMSR_LS));
+ } while (!(status & BMSR_LSTATUS));
return 0;
}
static int fec_get_hwaddr(struct eth_device *dev, unsigned char *mac)
{
-/*
- * The MX27 can store the mac address in internal eeprom
- * This mechanism is not supported now by MX51
- */
-#ifdef CONFIG_MX51
- return -1;
-#else
- struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
- int i;
-
- for (i = 0; i < 6; i++)
- mac[6-1-i] = readl(&iim->iim_bank_area0[IIM0_MAC + i]);
-
- return is_valid_ether_addr(mac);
-#endif
+ imx_get_mac_from_fuse(mac);
+ return !is_valid_ether_addr(mac);
}
static int fec_set_hwaddr(struct eth_device *dev)
/*
* Enable FEC-Lite controller
*/
- writel(FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl);
+ writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN,
+ &fec->eth->ecntrl);
+#if defined(CONFIG_MX25) || defined(CONFIG_MX53)
+ udelay(100);
+ /*
+ * setup the MII gasket for RMII mode
+ */
+
+ /* disable the gasket */
+ writew(0, &fec->eth->miigsk_enr);
+
+ /* wait for the gasket to be disabled */
+ while (readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY)
+ udelay(2);
+
+ /* configure gasket for RMII, 50 MHz, no loopback, and no echo */
+ writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr);
+
+ /* re-enable the gasket */
+ writew(MIIGSK_ENR_EN, &fec->eth->miigsk_enr);
+
+ /* wait until MII gasket is ready */
+ int max_loops = 10;
+ while ((readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) == 0) {
+ if (--max_loops <= 0) {
+ printf("WAIT for MII Gasket ready timed out\n");
+ break;
+ }
+ }
+#endif
miiphy_wait_aneg(edev);
miiphy_speed(edev->name, CONFIG_FEC_MXC_PHYADDR);
uint32_t base;
struct fec_priv *fec = (struct fec_priv *)dev->priv;
+ /* Initialize MAC address */
+ fec_set_hwaddr(dev);
+
/*
* reserve memory for both buffer descriptor chains at once
* Datasheet forces the startaddress of each chain is 16 byte
miiphy_restart_aneg(dev);
fec_open(dev);
- fec_set_hwaddr(dev);
return 0;
}
/*
* issue graceful stop command to the FEC transmitter if necessary
*/
- writel(FEC_ECNTRL_RESET | readl(&fec->eth->x_cntrl),
+ writel(FEC_TCNTRL_GTS | readl(&fec->eth->x_cntrl),
&fec->eth->x_cntrl);
debug("eth_halt: wait for stop regs\n");
* wait for graceful stop to register
*/
while ((counter--) && (!(readl(&fec->eth->ievent) & FEC_IEVENT_GRA)))
- ; /* FIXME ensure time */
+ udelay(1);
/*
* Disable SmartDMA tasks
* Disable the Ethernet Controller
* Note: this will also reset the BD index counter!
*/
- writel(0, &fec->eth->ecntrl);
+ writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN,
+ &fec->eth->ecntrl);
fec->rbd_index = 0;
fec->tbd_index = 0;
debug("eth_halt: done\n");
* wait until frame is sent .
*/
while (readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY) {
- /* FIXME: Timeout */
+ udelay(1);
}
debug("fec_send: status 0x%x index %d\n",
readw(&fec->tbd_base[fec->tbd_index].status),
puts("fec_mxc: not enough malloc memory\n");
return -ENOMEM;
}
+ memset(edev, 0, sizeof(*edev));
edev->priv = fec;
edev->init = fec_init;
edev->send = fec_send;
edev->recv = fec_recv;
edev->halt = fec_halt;
+ edev->write_hwaddr = fec_set_hwaddr;
fec->eth = (struct ethernet_regs *)IMX_FEC_BASE;
fec->bd = bd;
fec->xcv_type = MII100;
/* Reset chip. */
- writel(FEC_ECNTRL_RESET, &fec->eth->ecntrl);
+ writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_RESET, &fec->eth->ecntrl);
while (readl(&fec->eth->ecntrl) & 1)
udelay(10);
writel(0x05ee0024, &fec->eth->r_cntrl); /* FIXME 0x05ee0004 */
fec_mii_setspeed(fec);
- sprintf(edev->name, "FEC_MXC");
+ sprintf(edev->name, "FEC");
miiphy_register(edev->name, fec_miiphy_read, fec_miiphy_write);
eth_register(edev);
if (fec_get_hwaddr(edev, ethaddr) == 0) {
- printf("got MAC address from EEPROM: %pM\n", ethaddr);
+ printf("got MAC address from fuse: %pM\n", ethaddr);
memcpy(edev->enetaddr, ethaddr, 6);
- fec_set_hwaddr(edev);
}
return 0;