for DM9000A.
- Adapted reset procedure to match DM9000 application
notes (i.e. double reset)
+ - some minor code cleanups
These changes are tested with DM9000{A,EP,E} together
- with a 200MHz Atmel AT91SAM92161 core
+ with a 200MHz Atmel AT91SAM9261 core
-TODO: Homerun NIC and longrun NIC are not functional, only internal at the
- moment.
+TODO: external MII is not functional, only internal at the moment.
*/
#include <common.h>
#include <command.h>
#include <net.h>
#include <asm/io.h>
-
-#ifdef CONFIG_DRIVER_DM9000
+#include <dm9000.h>
#include "dm9000x.h"
/* Board/System/Debug information/definition ---------------- */
-#define DM9801_NOISE_FLOOR 0x08
-#define DM9802_NOISE_FLOOR 0x05
-
/* #define CONFIG_DM9000_DEBUG */
#ifdef CONFIG_DM9000_DEBUG
#define DM9000_DMP_PACKET(func,packet,length) \
do { \
int i; \
- printf(func ": length: %d\n", length); \
+ printf("%s: length: %d\n", func, length); \
for (i = 0; i < length; i++) { \
if (i % 8 == 0) \
printf("\n%s: %02x: ", func, i); \
#define DM9000_DMP_PACKET(func,packet,length)
#endif
-enum DM9000_PHY_mode { DM9000_10MHD = 0, DM9000_100MHD =
- 1, DM9000_10MFD = 4, DM9000_100MFD = 5, DM9000_AUTO =
- 8, DM9000_1M_HPNA = 0x10
-};
-enum DM9000_NIC_TYPE { FASTETHER_NIC = 0, HOMERUN_NIC = 1, LONGRUN_NIC = 2
-};
-
/* Structure/enum declaration ------------------------------- */
typedef struct board_info {
u32 runt_length_counter; /* counter: RX length < 64byte */
u16 dbug_cnt;
u8 phy_addr;
u8 device_wait_reset; /* device state */
- u8 nic_type; /* NIC type */
unsigned char srom[128];
- void (*outblk)(void *data_ptr, int count);
+ void (*outblk)(volatile void *data_ptr, int count);
void (*inblk)(void *data_ptr, int count);
void (*rx_status)(u16 *RxStatus, u16 *RxLen);
- } board_info_t;
+ struct eth_device netdev;
+} board_info_t;
static board_info_t dm9000_info;
-/* For module input parameter */
-static int media_mode = DM9000_AUTO;
-static u8 nfloor = 0;
/* function declaration ------------------------------------- */
-int eth_init(bd_t * bd);
-int eth_send(volatile void *, int);
-int eth_rx(void);
-void eth_halt(void);
static int dm9000_probe(void);
static u16 phy_read(int);
static void phy_write(int, u16);
-u16 read_srom_word(int);
static u8 DM9000_ior(int);
static void DM9000_iow(int reg, u8 value);
/* DM9000 network board routine ---------------------------- */
-#define DM9000_outb(d,r) ( *(volatile u8 *)r = d )
-#define DM9000_outw(d,r) ( *(volatile u16 *)r = d )
-#define DM9000_outl(d,r) ( *(volatile u32 *)r = d )
-#define DM9000_inb(r) (*(volatile u8 *)r)
-#define DM9000_inw(r) (*(volatile u16 *)r)
-#define DM9000_inl(r) (*(volatile u32 *)r)
+#define DM9000_outb(d,r) outb(d, r)
+#define DM9000_outw(d,r) outw(d, r)
+#define DM9000_outl(d,r) outl(d, r)
+#define DM9000_inb(r) inb(r)
+#define DM9000_inw(r) inw(r)
+#define DM9000_inl(r) inl(r)
#ifdef CONFIG_DM9000_DEBUG
static void
}
#endif
-static void dm9000_outblk_8bit(void *data_ptr, int count)
+static void dm9000_outblk_8bit(volatile void *data_ptr, int count)
{
int i;
for (i = 0; i < count; i++)
DM9000_outb((((u8 *) data_ptr)[i] & 0xff), DM9000_DATA);
}
-static void dm9000_outblk_16bit(void *data_ptr, int count)
+static void dm9000_outblk_16bit(volatile void *data_ptr, int count)
{
int i;
u32 tmplen = (count + 1) / 2;
for (i = 0; i < tmplen; i++)
DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA);
}
-static void dm9000_outblk_32bit(void *data_ptr, int count)
+static void dm9000_outblk_32bit(volatile void *data_ptr, int count)
{
int i;
u32 tmplen = (count + 3) / 4;
static void dm9000_rx_status_32bit(u16 *RxStatus, u16 *RxLen)
{
- u32 tmpdata = DM9000_inl(DM9000_DATA);
+ u32 tmpdata;
DM9000_outb(DM9000_MRCMD, DM9000_IO);
- *RxStatus = tmpdata;
- *RxLen = tmpdata >> 16;
+ tmpdata = DM9000_inl(DM9000_DATA);
+ *RxStatus = __le16_to_cpu(tmpdata);
+ *RxLen = __le16_to_cpu(tmpdata >> 16);
}
static void dm9000_rx_status_16bit(u16 *RxStatus, u16 *RxLen)
{
DM9000_outb(DM9000_MRCMD, DM9000_IO);
- *RxStatus = DM9000_inw(DM9000_DATA);
- *RxLen = DM9000_inw(DM9000_DATA);
+ *RxStatus = __le16_to_cpu(DM9000_inw(DM9000_DATA));
+ *RxLen = __le16_to_cpu(DM9000_inw(DM9000_DATA));
}
static void dm9000_rx_status_8bit(u16 *RxStatus, u16 *RxLen)
{
DM9000_outb(DM9000_MRCMD, DM9000_IO);
- *RxStatus = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
- *RxLen = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
+ *RxStatus =
+ __le16_to_cpu(DM9000_inb(DM9000_DATA) +
+ (DM9000_inb(DM9000_DATA) << 8));
+ *RxLen =
+ __le16_to_cpu(DM9000_inb(DM9000_DATA) +
+ (DM9000_inb(DM9000_DATA) << 8));
}
/*
}
}
-/* Set PHY operationg mode
-*/
-static void
-set_PHY_mode(void)
-{
- u16 phy_reg4 = 0x01e1, phy_reg0 = 0x1000;
- if (!(media_mode & DM9000_AUTO)) {
- switch (media_mode) {
- case DM9000_10MHD:
- phy_reg4 = 0x21;
- phy_reg0 = 0x0000;
- break;
- case DM9000_10MFD:
- phy_reg4 = 0x41;
- phy_reg0 = 0x1100;
- break;
- case DM9000_100MHD:
- phy_reg4 = 0x81;
- phy_reg0 = 0x2000;
- break;
- case DM9000_100MFD:
- phy_reg4 = 0x101;
- phy_reg0 = 0x3100;
- break;
- }
- phy_write(4, phy_reg4); /* Set PHY media mode */
- phy_write(0, phy_reg0); /* Tmp */
- }
- DM9000_iow(DM9000_GPCR, 0x01); /* Let GPIO0 output */
- DM9000_iow(DM9000_GPR, 0x00); /* Enable PHY */
-}
-
-/*
- Init HomeRun DM9801
-*/
-static void
-program_dm9801(u16 HPNA_rev)
-{
- __u16 reg16, reg17, reg24, reg25;
- if (!nfloor)
- nfloor = DM9801_NOISE_FLOOR;
- reg16 = phy_read(16);
- reg17 = phy_read(17);
- reg24 = phy_read(24);
- reg25 = phy_read(25);
- switch (HPNA_rev) {
- case 0xb900: /* DM9801 E3 */
- reg16 |= 0x1000;
- reg25 = ((reg24 + nfloor) & 0x00ff) | 0xf000;
- break;
- case 0xb901: /* DM9801 E4 */
- reg25 = ((reg24 + nfloor) & 0x00ff) | 0xc200;
- reg17 = (reg17 & 0xfff0) + nfloor + 3;
- break;
- case 0xb902: /* DM9801 E5 */
- case 0xb903: /* DM9801 E6 */
- default:
- reg16 |= 0x1000;
- reg25 = ((reg24 + nfloor - 3) & 0x00ff) | 0xc200;
- reg17 = (reg17 & 0xfff0) + nfloor;
- }
- phy_write(16, reg16);
- phy_write(17, reg17);
- phy_write(25, reg25);
-}
-
-/*
- Init LongRun DM9802
-*/
-static void
-program_dm9802(void)
-{
- __u16 reg25;
- if (!nfloor)
- nfloor = DM9802_NOISE_FLOOR;
- reg25 = phy_read(25);
- reg25 = (reg25 & 0xff00) + nfloor;
- phy_write(25, reg25);
-}
-
-/* Identify NIC type
-*/
-static void
-identify_nic(void)
-{
- struct board_info *db = &dm9000_info;
- u16 phy_reg3;
- DM9000_iow(DM9000_NCR, NCR_EXT_PHY);
- phy_reg3 = phy_read(3);
- switch (phy_reg3 & 0xfff0) {
- case 0xb900:
- if (phy_read(31) == 0x4404) {
- db->nic_type = HOMERUN_NIC;
- program_dm9801(phy_reg3);
- DM9000_DBG("found homerun NIC\n");
- } else {
- db->nic_type = LONGRUN_NIC;
- DM9000_DBG("found longrun NIC\n");
- program_dm9802();
- }
- break;
- default:
- db->nic_type = FASTETHER_NIC;
- break;
- }
- DM9000_iow(DM9000_NCR, 0);
-}
-
/* General Purpose dm9000 reset routine */
static void
dm9000_reset(void)
/* Reset DM9000,
see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */
- /* DEBUG: Make all GPIO pins outputs */
- DM9000_iow(DM9000_GPCR, 0x0F);
+ /* DEBUG: Make all GPIO0 outputs, all others inputs */
+ DM9000_iow(DM9000_GPCR, GPCR_GPIO0_OUT);
/* Step 1: Power internal PHY by writing 0 to GPIO0 pin */
DM9000_iow(DM9000_GPR, 0);
/* Step 2: Software reset */
- DM9000_iow(DM9000_NCR, 3);
+ DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST));
do {
DM9000_DBG("resetting the DM9000, 1st reset\n");
} while (DM9000_ior(DM9000_NCR) & 1);
DM9000_iow(DM9000_NCR, 0);
- DM9000_iow(DM9000_NCR, 3); /* Issue a second reset */
+ DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST)); /* Issue a second reset */
do {
DM9000_DBG("resetting the DM9000, 2nd reset\n");
printf("ERROR: resetting DM9000 -> not responding\n");
}
-/* Initilize dm9000 board
+/* Initialize dm9000 board
*/
-int
-eth_init(bd_t * bd)
+static int dm9000_init(struct eth_device *dev, bd_t *bd)
{
int i, oft, lnk;
u8 io_mode;
struct board_info *db = &dm9000_info;
- DM9000_DBG("eth_init()\n");
+ DM9000_DBG("%s\n", __func__);
/* RESET device */
dm9000_reset();
- dm9000_probe();
+
+ if (dm9000_probe() < 0)
+ return -1;
/* Auto-detect 8/16/32 bit mode, ISR Bit 6+7 indicate bus width */
io_mode = DM9000_ior(DM9000_ISR) >> 6;
break;
}
- /* NIC Type: FASTETHER, HOMERUN, LONGRUN */
- identify_nic();
-
- /* GPIO0 on pre-activate PHY */
- DM9000_iow(DM9000_GPR, 0x00); /*REG_1F bit0 activate phyxcer */
-
- /* Set PHY */
- set_PHY_mode();
-
- /* Program operating register */
- DM9000_iow(DM9000_NCR, 0x0); /* only intern phy supported by now */
- DM9000_iow(DM9000_TCR, 0); /* TX Polling clear */
- DM9000_iow(DM9000_BPTR, 0x3f); /* Less 3Kb, 200us */
- DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8)); /* Flow Control : High/Low Water */
- DM9000_iow(DM9000_FCR, 0x0); /* SH FIXME: This looks strange! Flow Control */
- DM9000_iow(DM9000_SMCR, 0); /* Special Mode */
- DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); /* clear TX status */
- DM9000_iow(DM9000_ISR, 0x0f); /* Clear interrupt status */
-
- /* Set Node address */
- for (i = 0; i < 6; i++)
- ((u16 *) bd->bi_enetaddr)[i] = read_srom_word(i);
-
- if (is_zero_ether_addr(bd->bi_enetaddr) ||
- is_multicast_ether_addr(bd->bi_enetaddr)) {
- /* try reading from environment */
- u8 i;
- char *s, *e;
- s = getenv ("ethaddr");
- for (i = 0; i < 6; ++i) {
- bd->bi_enetaddr[i] = s ?
- simple_strtoul (s, &e, 16) : 0;
- if (s)
- s = (*e) ? e + 1 : e;
- }
- }
-
- printf("MAC: %02x:%02x:%02x:%02x:%02x:%02x\n", bd->bi_enetaddr[0],
- bd->bi_enetaddr[1], bd->bi_enetaddr[2], bd->bi_enetaddr[3],
- bd->bi_enetaddr[4], bd->bi_enetaddr[5]);
- for (i = 0, oft = 0x10; i < 6; i++, oft++)
- DM9000_iow(oft, bd->bi_enetaddr[i]);
+ /* Program operating register, only internal phy supported */
+ DM9000_iow(DM9000_NCR, 0x0);
+ /* TX Polling clear */
+ DM9000_iow(DM9000_TCR, 0);
+ /* Less 3Kb, 200us */
+ DM9000_iow(DM9000_BPTR, BPTR_BPHW(3) | BPTR_JPT_600US);
+ /* Flow Control : High/Low Water */
+ DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8));
+ /* SH FIXME: This looks strange! Flow Control */
+ DM9000_iow(DM9000_FCR, 0x0);
+ /* Special Mode */
+ DM9000_iow(DM9000_SMCR, 0);
+ /* clear TX status */
+ DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END);
+ /* Clear interrupt status */
+ DM9000_iow(DM9000_ISR, ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS);
+
+ printf("MAC: %pM\n", dev->enetaddr);
+
+ /* fill device MAC address registers */
+ for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++)
+ DM9000_iow(oft, dev->enetaddr[i]);
for (i = 0, oft = 0x16; i < 8; i++, oft++)
DM9000_iow(oft, 0xff);
DM9000_DBG("\n");
/* Activate DM9000 */
- DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN); /* RX enable */
- DM9000_iow(DM9000_IMR, IMR_PAR); /* Enable TX/RX interrupt mask */
+ /* RX enable */
+ DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN);
+ /* Enable TX/RX interrupt mask */
+ DM9000_iow(DM9000_IMR, IMR_PAR);
+
i = 0;
while (!(phy_read(1) & 0x20)) { /* autonegation complete bit */
udelay(1000);
Hardware start transmission.
Send a packet to media from the upper layer.
*/
-int
-eth_send(volatile void *packet, int length)
+static int dm9000_send(struct eth_device *netdev, volatile void *packet,
+ int length)
{
- char *data_ptr;
int tmo;
struct board_info *db = &dm9000_info;
- DM9000_DMP_PACKET("eth_send", packet, length);
+ DM9000_DMP_PACKET(__func__ , packet, length);
DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */
/* Move data to DM9000 TX RAM */
- data_ptr = (char *) packet;
DM9000_outb(DM9000_MWCMD, DM9000_IO); /* Prepare for TX-data */
/* push the data to the TX-fifo */
- (db->outblk)(data_ptr, length);
+ (db->outblk)(packet, length);
/* Set TX length to DM9000 */
DM9000_iow(DM9000_TXPLL, length & 0xff);
DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */
/* wait for end of transmission */
- tmo = get_timer(0) + 5 * CFG_HZ;
+ tmo = get_timer(0) + 5 * CONFIG_SYS_HZ;
while ( !(DM9000_ior(DM9000_NSR) & (NSR_TX1END | NSR_TX2END)) ||
!(DM9000_ior(DM9000_ISR) & IMR_PTM) ) {
if (get_timer(0) >= tmo) {
Stop the interface.
The interface is stopped when it is brought.
*/
-void
-eth_halt(void)
+static void dm9000_halt(struct eth_device *netdev)
{
- DM9000_DBG("eth_halt\n");
+ DM9000_DBG("%s\n", __func__);
/* RESET devie */
phy_write(0, 0x8000); /* PHY RESET */
/*
Received a packet and pass to upper layer
*/
-int
-eth_rx(void)
+static int dm9000_rx(struct eth_device *netdev)
{
u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0];
u16 RxStatus, RxLen = 0;
for (;;) {
DM9000_ior(DM9000_MRCMDX); /* Dummy read */
- /* Get most updated data */
- rxbyte = DM9000_inb(DM9000_DATA);
+ /* Get most updated data,
+ only look at bits 0:1, See application notes DM9000 */
+ rxbyte = DM9000_inb(DM9000_DATA) & 0x03;
/* Status check: this byte must be 0 or 1 */
if (rxbyte > DM9000_PKT_RDY) {
dm9000_reset();
}
} else {
- DM9000_DMP_PACKET("eth_rx", rdptr, RxLen);
+ DM9000_DMP_PACKET(__func__ , rdptr, RxLen);
DM9000_DBG("passing packet to upper layer\n");
NetReceive(NetRxPackets[0], RxLen);
/*
Read a word data from SROM
*/
-u16
-read_srom_word(int offset)
+#if !defined(CONFIG_DM9000_NO_SROM)
+void dm9000_read_srom_word(int offset, u8 *to)
{
DM9000_iow(DM9000_EPAR, offset);
DM9000_iow(DM9000_EPCR, 0x4);
udelay(8000);
DM9000_iow(DM9000_EPCR, 0x0);
- return (DM9000_ior(DM9000_EPDRL) + (DM9000_ior(DM9000_EPDRH) << 8));
+ to[0] = DM9000_ior(DM9000_EPDRL);
+ to[1] = DM9000_ior(DM9000_EPDRH);
}
-void
-write_srom_word(int offset, u16 val)
+void dm9000_write_srom_word(int offset, u16 val)
{
DM9000_iow(DM9000_EPAR, offset);
DM9000_iow(DM9000_EPDRH, ((val >> 8) & 0xff));
udelay(8000);
DM9000_iow(DM9000_EPCR, 0);
}
+#endif
+static void dm9000_get_enetaddr(struct eth_device *dev)
+{
+#if !defined(CONFIG_DM9000_NO_SROM)
+ int i;
+ for (i = 0; i < 3; i++)
+ dm9000_read_srom_word(i, dev->enetaddr + (2 * i));
+#endif
+}
/*
Read a byte from I/O port
/* Fill the phyxcer register into REG_0C */
DM9000_iow(DM9000_EPAR, DM9000_PHY | reg);
DM9000_iow(DM9000_EPCR, 0xc); /* Issue phyxcer read command */
- udelay(100); /* Wait read complete */
+ udelay(100); /* Wait read complete */
DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer read command */
val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL);
DM9000_iow(DM9000_EPDRL, (value & 0xff));
DM9000_iow(DM9000_EPDRH, ((value >> 8) & 0xff));
DM9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */
- udelay(500); /* Wait write complete */
+ udelay(500); /* Wait write complete */
DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */
DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value);
}
-#endif /* CONFIG_DRIVER_DM9000 */
+
+int dm9000_initialize(bd_t *bis)
+{
+ struct eth_device *dev = &(dm9000_info.netdev);
+
+ /* Load MAC address from EEPROM */
+ dm9000_get_enetaddr(dev);
+
+ dev->init = dm9000_init;
+ dev->halt = dm9000_halt;
+ dev->send = dm9000_send;
+ dev->recv = dm9000_rx;
+ sprintf(dev->name, "dm9000");
+
+ eth_register(dev);
+
+ return 0;
+}