net: sun8i_emac: Retrieve GMAC clock via 'syscon' phandle

[oweals/u-boot.git] / drivers / net / Kconfig

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index f1f0e2d94ef164ce4666bc6bf222006e374c510f..77d0b3a01f433dd10e678a387caa4dda7dd9d7ad 100644 (file)
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -11,13 +11,6 @@ config DM_ETH
          This is currently implemented in net/eth-uclass.c
          Look in include/net.h for details.
 
-config DRIVER_TI_CPSW
-       bool "TI Common Platform Ethernet Switch"
-       select PHYLIB
-       help
-         This driver supports the TI three port switch gigabit ethernet
-         subsystem found in the TI SoCs.
-
 menuconfig NETDEVICES
        bool "Network device support"
        depends on NET
@@ -79,6 +72,24 @@ config BCM_SF2_ETH_GMAC
          by the BCM_SF2_ETH driver.
          Say Y to any bcmcygnus based platforms.
 
+config BCM6348_ETH
+       bool "BCM6348 EMAC support"
+       depends on DM_ETH && ARCH_BMIPS
+       select DMA
+       select DMA_CHANNELS
+       select MII
+       select PHYLIB
+       help
+         This driver supports the BCM6348 Ethernet MAC.
+
+config BCM6368_ETH
+       bool "BCM6368 EMAC support"
+       depends on DM_ETH && ARCH_BMIPS
+       select DMA
+       select MII
+       help
+         This driver supports the BCM6368 Ethernet MAC.
+
 config DWC_ETH_QOS
        bool "Synopsys DWC Ethernet QOS device support"
        depends on DM_ETH
@@ -145,12 +156,15 @@ config ETH_SANDBOX_RAW
 config ETH_DESIGNWARE
        bool "Synopsys Designware Ethernet MAC"
        select PHYLIB
+       imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
        help
          This MAC is present in SoCs from various vendors. It supports
          100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
          provide the PHY (physical media interface).
 
 config ETH_DESIGNWARE_SOCFPGA
+       select REGMAP
+       select SYSCON
        bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
        depends on DM_ETH && ETH_DESIGNWARE
        help
@@ -176,7 +190,7 @@ config FEC_MXC_MDIO_BASE
 
 config FEC_MXC
        bool "FEC Ethernet controller"
-       depends on MX5 || MX6 || MX7
+       depends on MX5 || MX6 || MX7 || IMX8
        help
          This driver supports the 10/100 Fast Ethernet controller for
          NXP i.MX processors.
@@ -186,6 +200,32 @@ config FTMAC100
        help
          This MAC is present in Andestech SoCs.
 
+config FTGMAC100
+       bool "Ftgmac100 Ethernet Support"
+       depends on DM_ETH
+       select PHYLIB
+       help
+         This driver supports the Faraday's FTGMAC100 Gigabit SoC
+         Ethernet controller that can be found on Aspeed SoCs (which
+         include NCSI).
+
+         It is fully compliant with IEEE 802.3 specification for
+         10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
+         Mbps Ethernet and includes Reduced Media Independent
+         Interface (RMII) and Reduced Gigabit Media Independent
+         Interface (RGMII) interfaces. It adopts an AHB bus interface
+         and integrates a link list DMA engine with direct M-Bus
+         accesses for transmitting and receiving packets. It has
+         independent TX/RX fifos, supports half and full duplex (1000
+         Mbps mode only supports full duplex), flow control for full
+         duplex and backpressure for half duplex.
+
+         The FTGMAC100 also implements IP, TCP, UDP checksum offloads
+         and supports IEEE 802.1Q VLAN tag insertion and removal. It
+         offers high-priority transmit queue for QoS and CoS
+         applications.
+
+
 config MVGBE
        bool "Marvell Orion5x/Kirkwood network interface support"
        depends on KIRKWOOD || ORION5X
@@ -227,6 +267,13 @@ config MACB_ZYNQ
          The Cadence MACB ethernet interface was used on Zynq platform.
          Say Y to enable support for the MACB/GEM in Zynq chip.
 
+config MT7628_ETH
+       bool "MediaTek MT7628 Ethernet Interface"
+       depends on ARCH_MT7620
+       help
+         The MediaTek MT7628 ethernet interface is used on MT7628 and
+         MT7688 based boards.
+
 config PCH_GBE
        bool "Intel Platform Controller Hub EG20T GMAC driver"
        depends on DM_ETH && DM_PCI
@@ -322,10 +369,7 @@ config SH_ETHER
        help
          This driver supports the Ethernet for Renesas SH and ARM SoCs.
 
-config DRIVER_TI_EMAC
-       bool "TI Davinci EMAC"
-       help
-          Support for davinci emac
+source "drivers/net/ti/Kconfig"
 
 config XILINX_AXIEMAC
        depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
@@ -391,6 +435,8 @@ config SNI_AVE
          This driver implements support for the Socionext AVE Ethernet
          controller, as found on the Socionext UniPhier family.
 
+source "drivers/net/mscc_eswitch/Kconfig"
+
 config ETHER_ON_FEC1
        bool "FEC1"
        depends on MPC8XX_FEC
@@ -472,4 +518,14 @@ config TSEC_ENET
          This driver implements support for the (Enhanced) Three-Speed
          Ethernet Controller found on Freescale SoCs.
 
+config MEDIATEK_ETH
+       bool "MediaTek Ethernet GMAC Driver"
+       depends on DM_ETH
+       select PHYLIB
+       select DM_GPIO
+       select DM_RESET
+       help
+         This Driver support MediaTek Ethernet GMAC
+         Say Y to enable support for the MediaTek Ethernet GMAC.
+
 endif # NETDEVICES