* Overview:
* This is the generic MTD driver for NAND flash devices. It should be
* capable of working with almost all NAND chips currently available.
- * Basic support for AG-AND chips is provided.
*
* Additional technical information is available on
* http://www.linux-mtd.infradead.org/doc/nand.html
* TODO:
* Enable cached programming for 2k page size chips
* Check, if mtd->ecctype should be set to MTD_ECC_HW
- * if we have HW ecc support.
- * The AG-AND chips have nice features for speed improvement,
- * which are not supported yet. Read / program 4 pages in one go.
+ * if we have HW ECC support.
* BBT table is not serialized, has to be fixed
*
* This program is free software; you can redistribute it and/or modify
*
*/
-#include <common.h>
-
-#define ENOTSUPP 524 /* Operation is not supported */
+#ifndef __UBOOT__
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/nand_bch.h>
+#include <linux/interrupt.h>
+#include <linux/bitops.h>
+#include <linux/leds.h>
+#include <linux/io.h>
+#include <linux/mtd/partitions.h>
+#else
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+#include <common.h>
#include <malloc.h>
#include <watchdog.h>
#include <linux/err.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/nand_bch.h>
-
#ifdef CONFIG_MTD_PARTITIONS
#include <linux/mtd/partitions.h>
#endif
-
#include <asm/io.h>
#include <asm/errno.h>
#define CONFIG_SYS_NAND_RESET_CNT 200000
#endif
+static bool is_module_text_address(unsigned long addr) {return 0;}
+#endif
+
/* Define default oob placement schemes for large and small page devices */
static struct nand_ecclayout nand_oob_8 = {
.eccbytes = 3,
.length = 78} }
};
-static int nand_get_device(struct nand_chip *chip, struct mtd_info *mtd,
- int new_state);
+static int nand_get_device(struct mtd_info *mtd, int new_state);
static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
struct mtd_oob_ops *ops);
-static int nand_wait(struct mtd_info *mtd, struct nand_chip *this);
+/*
+ * For devices which display every fart in the system on a separate LED. Is
+ * compiled away when LED support is disabled.
+ */
+DEFINE_LED_TRIGGER(nand_led_trigger);
static int check_offs_len(struct mtd_info *mtd,
loff_t ofs, uint64_t len)
int ret = 0;
/* Start address must align on block boundary */
- if (ofs & ((1 << chip->phys_erase_shift) - 1)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Unaligned address\n", __func__);
+ if (ofs & ((1ULL << chip->phys_erase_shift) - 1)) {
+ pr_debug("%s: unaligned address\n", __func__);
ret = -EINVAL;
}
/* Length must align on block boundary */
- if (len & ((1 << chip->phys_erase_shift) - 1)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Length not block aligned\n",
- __func__);
- ret = -EINVAL;
- }
-
- /* Do not allow past end of device */
- if (ofs + len > mtd->size) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Past end of device\n",
- __func__);
+ if (len & ((1ULL << chip->phys_erase_shift) - 1)) {
+ pr_debug("%s: length not block aligned\n", __func__);
ret = -EINVAL;
}
/**
* nand_release_device - [GENERIC] release chip
- * @mtd: MTD device structure
+ * @mtd: MTD device structure
*
- * Deselect, release chip lock and wake up anyone waiting on the device
+ * Release chip lock and wake up anyone waiting on the device.
*/
static void nand_release_device(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
+#ifndef __UBOOT__
+ /* Release the controller and the chip */
+ spin_lock(&chip->controller->lock);
+ chip->controller->active = NULL;
+ chip->state = FL_READY;
+ wake_up(&chip->controller->wq);
+ spin_unlock(&chip->controller->lock);
+#else
/* De-select the NAND device */
chip->select_chip(mtd, -1);
+#endif
}
/**
* nand_read_byte - [DEFAULT] read one byte from the chip
- * @mtd: MTD device structure
+ * @mtd: MTD device structure
*
- * Default read function for 8bit buswith
+ * Default read function for 8bit buswidth
*/
+#ifndef __UBOOT__
+static uint8_t nand_read_byte(struct mtd_info *mtd)
+#else
uint8_t nand_read_byte(struct mtd_info *mtd)
+#endif
{
struct nand_chip *chip = mtd->priv;
return readb(chip->IO_ADDR_R);
}
/**
- * nand_read_byte16 - [DEFAULT] read one byte endianess aware from the chip
- * @mtd: MTD device structure
+ * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
+ * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
+ * @mtd: MTD device structure
+ *
+ * Default read function for 16bit buswidth with endianness conversion.
*
- * Default read function for 16bit buswith with
- * endianess conversion
*/
static uint8_t nand_read_byte16(struct mtd_info *mtd)
{
/**
* nand_read_word - [DEFAULT] read one word from the chip
- * @mtd: MTD device structure
+ * @mtd: MTD device structure
*
- * Default read function for 16bit buswith without
- * endianess conversion
+ * Default read function for 16bit buswidth without endianness conversion.
*/
static u16 nand_read_word(struct mtd_info *mtd)
{
/**
* nand_select_chip - [DEFAULT] control CE line
- * @mtd: MTD device structure
- * @chipnr: chipnumber to select, -1 for deselect
+ * @mtd: MTD device structure
+ * @chipnr: chipnumber to select, -1 for deselect
*
* Default select function for 1 chip devices.
*/
}
}
+/**
+ * nand_write_byte - [DEFAULT] write single byte to chip
+ * @mtd: MTD device structure
+ * @byte: value to write
+ *
+ * Default function to write a byte to I/O[7:0]
+ */
+static void nand_write_byte(struct mtd_info *mtd, uint8_t byte)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ chip->write_buf(mtd, &byte, 1);
+}
+
+/**
+ * nand_write_byte16 - [DEFAULT] write single byte to a chip with width 16
+ * @mtd: MTD device structure
+ * @byte: value to write
+ *
+ * Default function to write a byte to I/O[7:0] on a 16-bit wide chip.
+ */
+static void nand_write_byte16(struct mtd_info *mtd, uint8_t byte)
+{
+ struct nand_chip *chip = mtd->priv;
+ uint16_t word = byte;
+
+ /*
+ * It's not entirely clear what should happen to I/O[15:8] when writing
+ * a byte. The ONFi spec (Revision 3.1; 2012-09-19, Section 2.16) reads:
+ *
+ * When the host supports a 16-bit bus width, only data is
+ * transferred at the 16-bit width. All address and command line
+ * transfers shall use only the lower 8-bits of the data bus. During
+ * command transfers, the host may place any value on the upper
+ * 8-bits of the data bus. During address transfers, the host shall
+ * set the upper 8-bits of the data bus to 00h.
+ *
+ * One user of the write_byte callback is nand_onfi_set_features. The
+ * four parameters are specified to be written to I/O[7:0], but this is
+ * neither an address nor a command transfer. Let's assume a 0 on the
+ * upper I/O lines is OK.
+ */
+ chip->write_buf(mtd, (uint8_t *)&word, 2);
+}
+
+#if defined(__UBOOT__) && !defined(CONFIG_BLACKFIN)
+static void iowrite8_rep(void *addr, const uint8_t *buf, int len)
+{
+ int i;
+
+ for (i = 0; i < len; i++)
+ writeb(buf[i], addr);
+}
+static void ioread8_rep(void *addr, uint8_t *buf, int len)
+{
+ int i;
+
+ for (i = 0; i < len; i++)
+ buf[i] = readb(addr);
+}
+
+static void ioread16_rep(void *addr, void *buf, int len)
+{
+ int i;
+ u16 *p = (u16 *) buf;
+
+ for (i = 0; i < len; i++)
+ p[i] = readw(addr);
+}
+
+static void iowrite16_rep(void *addr, void *buf, int len)
+{
+ int i;
+ u16 *p = (u16 *) buf;
+
+ for (i = 0; i < len; i++)
+ writew(p[i], addr);
+}
+#endif
+
/**
* nand_write_buf - [DEFAULT] write buffer to chip
- * @mtd: MTD device structure
- * @buf: data buffer
- * @len: number of bytes to write
+ * @mtd: MTD device structure
+ * @buf: data buffer
+ * @len: number of bytes to write
*
- * Default write function for 8bit buswith
+ * Default write function for 8bit buswidth.
*/
+#ifndef __UBOOT__
+static void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+#else
void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+#endif
{
- int i;
struct nand_chip *chip = mtd->priv;
- for (i = 0; i < len; i++)
- writeb(buf[i], chip->IO_ADDR_W);
+ iowrite8_rep(chip->IO_ADDR_W, buf, len);
}
/**
* nand_read_buf - [DEFAULT] read chip data into buffer
- * @mtd: MTD device structure
- * @buf: buffer to store date
- * @len: number of bytes to read
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
*
- * Default read function for 8bit buswith
+ * Default read function for 8bit buswidth.
*/
+#ifndef __UBOOT__
+static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+#else
void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+#endif
{
- int i;
struct nand_chip *chip = mtd->priv;
- for (i = 0; i < len; i++)
- buf[i] = readb(chip->IO_ADDR_R);
+ ioread8_rep(chip->IO_ADDR_R, buf, len);
}
+#ifdef __UBOOT__
+#if defined(CONFIG_MTD_NAND_VERIFY_WRITE)
/**
* nand_verify_buf - [DEFAULT] Verify chip data against buffer
- * @mtd: MTD device structure
- * @buf: buffer containing the data to compare
- * @len: number of bytes to compare
+ * @mtd: MTD device structure
+ * @buf: buffer containing the data to compare
+ * @len: number of bytes to compare
*
- * Default verify function for 8bit buswith
+ * Default verify function for 8bit buswidth.
*/
static int nand_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
{
}
/**
- * nand_write_buf16 - [DEFAULT] write buffer to chip
- * @mtd: MTD device structure
- * @buf: data buffer
- * @len: number of bytes to write
+ * nand_verify_buf16 - [DEFAULT] Verify chip data against buffer
+ * @mtd: MTD device structure
+ * @buf: buffer containing the data to compare
+ * @len: number of bytes to compare
*
- * Default write function for 16bit buswith
+ * Default verify function for 16bit buswidth.
*/
-void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
+static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
{
int i;
struct nand_chip *chip = mtd->priv;
len >>= 1;
for (i = 0; i < len; i++)
- writew(p[i], chip->IO_ADDR_W);
+ if (p[i] != readw(chip->IO_ADDR_R))
+ return -EFAULT;
+ return 0;
}
+#endif
+#endif
/**
- * nand_read_buf16 - [DEFAULT] read chip data into buffer
- * @mtd: MTD device structure
- * @buf: buffer to store date
- * @len: number of bytes to read
+ * nand_write_buf16 - [DEFAULT] write buffer to chip
+ * @mtd: MTD device structure
+ * @buf: data buffer
+ * @len: number of bytes to write
*
- * Default read function for 16bit buswith
+ * Default write function for 16bit buswidth.
*/
-void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
+#ifndef __UBOOT__
+static void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
+#else
+void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
+#endif
{
- int i;
struct nand_chip *chip = mtd->priv;
u16 *p = (u16 *) buf;
- len >>= 1;
- for (i = 0; i < len; i++)
- p[i] = readw(chip->IO_ADDR_R);
+ iowrite16_rep(chip->IO_ADDR_W, p, len >> 1);
}
/**
- * nand_verify_buf16 - [DEFAULT] Verify chip data against buffer
- * @mtd: MTD device structure
- * @buf: buffer containing the data to compare
- * @len: number of bytes to compare
+ * nand_read_buf16 - [DEFAULT] read chip data into buffer
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
*
- * Default verify function for 16bit buswith
+ * Default read function for 16bit buswidth.
*/
-static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
+#ifndef __UBOOT__
+static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
+#else
+void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
+#endif
{
- int i;
struct nand_chip *chip = mtd->priv;
u16 *p = (u16 *) buf;
- len >>= 1;
- for (i = 0; i < len; i++)
- if (p[i] != readw(chip->IO_ADDR_R))
- return -EFAULT;
-
- return 0;
+ ioread16_rep(chip->IO_ADDR_R, p, len >> 1);
}
/**
* nand_block_bad - [DEFAULT] Read bad block marker from the chip
- * @mtd: MTD device structure
- * @ofs: offset from device start
- * @getchip: 0, if the chip is already selected
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ * @getchip: 0, if the chip is already selected
*
* Check, if the block is bad.
*/
static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
{
- int page, chipnr, res = 0;
+ int page, chipnr, res = 0, i = 0;
struct nand_chip *chip = mtd->priv;
u16 bad;
- if (chip->options & NAND_BBT_SCANLASTPAGE)
+ if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
ofs += mtd->erasesize - mtd->writesize;
page = (int)(ofs >> chip->page_shift) & chip->pagemask;
if (getchip) {
chipnr = (int)(ofs >> chip->chip_shift);
- nand_get_device(chip, mtd, FL_READING);
+ nand_get_device(mtd, FL_READING);
/* Select the NAND device */
chip->select_chip(mtd, chipnr);
}
- if (chip->options & NAND_BUSWIDTH_16) {
- chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos & 0xFE,
- page);
- bad = cpu_to_le16(chip->read_word(mtd));
- if (chip->badblockpos & 0x1)
- bad >>= 8;
- else
- bad &= 0xFF;
- } else {
- chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos, page);
- bad = chip->read_byte(mtd);
- }
+ do {
+ if (chip->options & NAND_BUSWIDTH_16) {
+ chip->cmdfunc(mtd, NAND_CMD_READOOB,
+ chip->badblockpos & 0xFE, page);
+ bad = cpu_to_le16(chip->read_word(mtd));
+ if (chip->badblockpos & 0x1)
+ bad >>= 8;
+ else
+ bad &= 0xFF;
+ } else {
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos,
+ page);
+ bad = chip->read_byte(mtd);
+ }
- if (likely(chip->badblockbits == 8))
- res = bad != 0xFF;
- else
- res = hweight8(bad) < chip->badblockbits;
+ if (likely(chip->badblockbits == 8))
+ res = bad != 0xFF;
+ else
+ res = hweight8(bad) < chip->badblockbits;
+ ofs += mtd->writesize;
+ page = (int)(ofs >> chip->page_shift) & chip->pagemask;
+ i++;
+ } while (!res && i < 2 && (chip->bbt_options & NAND_BBT_SCAN2NDPAGE));
- if (getchip)
+ if (getchip) {
+ chip->select_chip(mtd, -1);
nand_release_device(mtd);
+ }
return res;
}
/**
- * nand_default_block_markbad - [DEFAULT] mark a block bad
- * @mtd: MTD device structure
- * @ofs: offset from device start
+ * nand_default_block_markbad - [DEFAULT] mark a block bad via bad block marker
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
*
- * This is the default implementation, which can be overridden by
- * a hardware specific driver.
-*/
+ * This is the default implementation, which can be overridden by a hardware
+ * specific driver. It provides the details for writing a bad block marker to a
+ * block.
+ */
static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
{
struct nand_chip *chip = mtd->priv;
+ struct mtd_oob_ops ops;
uint8_t buf[2] = { 0, 0 };
- int block, ret, i = 0;
+ int ret = 0, res, i = 0;
+
+ ops.datbuf = NULL;
+ ops.oobbuf = buf;
+ ops.ooboffs = chip->badblockpos;
+ if (chip->options & NAND_BUSWIDTH_16) {
+ ops.ooboffs &= ~0x01;
+ ops.len = ops.ooblen = 2;
+ } else {
+ ops.len = ops.ooblen = 1;
+ }
+ ops.mode = MTD_OPS_PLACE_OOB;
- if (chip->options & NAND_BBT_SCANLASTPAGE)
+ /* Write to first/last page(s) if necessary */
+ if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
ofs += mtd->erasesize - mtd->writesize;
+ do {
+ res = nand_do_write_oob(mtd, ofs, &ops);
+ if (!ret)
+ ret = res;
- /* Get block number */
- block = (int)(ofs >> chip->bbt_erase_shift);
- if (chip->bbt)
- chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
+ i++;
+ ofs += mtd->writesize;
+ } while ((chip->bbt_options & NAND_BBT_SCAN2NDPAGE) && i < 2);
- /* Do we have a flash based bad block table ? */
- if (chip->options & NAND_USE_FLASH_BBT)
- ret = nand_update_bbt(mtd, ofs);
- else {
- nand_get_device(chip, mtd, FL_WRITING);
+ return ret;
+}
- /* Write to first two pages and to byte 1 and 6 if necessary.
- * If we write to more than one location, the first error
- * encountered quits the procedure. We write two bytes per
- * location, so we dont have to mess with 16 bit access.
- */
- do {
- chip->ops.len = chip->ops.ooblen = 2;
- chip->ops.datbuf = NULL;
- chip->ops.oobbuf = buf;
- chip->ops.ooboffs = chip->badblockpos & ~0x01;
-
- ret = nand_do_write_oob(mtd, ofs, &chip->ops);
-
- if (!ret && (chip->options & NAND_BBT_SCANBYTE1AND6)) {
- chip->ops.ooboffs = NAND_SMALL_BADBLOCK_POS
- & ~0x01;
- ret = nand_do_write_oob(mtd, ofs, &chip->ops);
- }
- i++;
- ofs += mtd->writesize;
- } while (!ret && (chip->options & NAND_BBT_SCAN2NDPAGE) &&
- i < 2);
+/**
+ * nand_block_markbad_lowlevel - mark a block bad
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ *
+ * This function performs the generic NAND bad block marking steps (i.e., bad
+ * block table(s) and/or marker(s)). We only allow the hardware driver to
+ * specify how to write bad block markers to OOB (chip->block_markbad).
+ *
+ * We try operations in the following order:
+ * (1) erase the affected block, to allow OOB marker to be written cleanly
+ * (2) write bad block marker to OOB area of affected block (unless flag
+ * NAND_BBT_NO_OOB_BBM is present)
+ * (3) update the BBT
+ * Note that we retain the first error encountered in (2) or (3), finish the
+ * procedures, and dump the error in the end.
+*/
+static int nand_block_markbad_lowlevel(struct mtd_info *mtd, loff_t ofs)
+{
+ struct nand_chip *chip = mtd->priv;
+ int res, ret = 0;
+
+ if (!(chip->bbt_options & NAND_BBT_NO_OOB_BBM)) {
+ struct erase_info einfo;
+
+ /* Attempt erase before marking OOB */
+ memset(&einfo, 0, sizeof(einfo));
+ einfo.mtd = mtd;
+ einfo.addr = ofs;
+ einfo.len = 1ULL << chip->phys_erase_shift;
+ nand_erase_nand(mtd, &einfo, 0);
+ /* Write bad block marker to OOB */
+ nand_get_device(mtd, FL_WRITING);
+ ret = chip->block_markbad(mtd, ofs);
nand_release_device(mtd);
}
+
+ /* Mark block bad in BBT */
+ if (chip->bbt) {
+ res = nand_markbad_bbt(mtd, ofs);
+ if (!ret)
+ ret = res;
+ }
+
if (!ret)
mtd->ecc_stats.badblocks++;
/**
* nand_check_wp - [GENERIC] check if the chip is write protected
- * @mtd: MTD device structure
- * Check, if the device is write protected
+ * @mtd: MTD device structure
*
- * The function expects, that the device is already selected
+ * Check, if the device is write protected. The function expects, that the
+ * device is already selected.
*/
static int nand_check_wp(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
- /* broken xD cards report WP despite being writable */
+ /* Broken xD cards report WP despite being writable */
if (chip->options & NAND_BROKEN_XD)
return 0;
/**
* nand_block_checkbad - [GENERIC] Check if a block is marked bad
- * @mtd: MTD device structure
- * @ofs: offset from device start
- * @getchip: 0, if the chip is already selected
- * @allowbbt: 1, if its allowed to access the bbt area
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ * @getchip: 0, if the chip is already selected
+ * @allowbbt: 1, if its allowed to access the bbt area
*
* Check, if the block is bad. Either by reading the bad block table or
* calling of the scan function.
struct nand_chip *chip = mtd->priv;
if (!(chip->options & NAND_BBT_SCANNED)) {
- chip->options |= NAND_BBT_SCANNED;
chip->scan_bbt(mtd);
+ chip->options |= NAND_BBT_SCANNED;
}
if (!chip->bbt)
return nand_isbad_bbt(mtd, ofs, allowbbt);
}
-/*
- * Wait for the ready pin, after a command
- * The timeout is catched later.
+#ifndef __UBOOT__
+/**
+ * panic_nand_wait_ready - [GENERIC] Wait for the ready pin after commands.
+ * @mtd: MTD device structure
+ * @timeo: Timeout
+ *
+ * Helper function for nand_wait_ready used when needing to wait in interrupt
+ * context.
*/
+static void panic_nand_wait_ready(struct mtd_info *mtd, unsigned long timeo)
+{
+ struct nand_chip *chip = mtd->priv;
+ int i;
+
+ /* Wait for the device to get ready */
+ for (i = 0; i < timeo; i++) {
+ if (chip->dev_ready(mtd))
+ break;
+ touch_softlockup_watchdog();
+ mdelay(1);
+ }
+}
+#endif
+
+/* Wait for the ready pin, after a command. The timeout is caught later. */
void nand_wait_ready(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
+#ifndef __UBOOT__
+ unsigned long timeo = jiffies + msecs_to_jiffies(20);
+
+ /* 400ms timeout */
+ if (in_interrupt() || oops_in_progress)
+ return panic_nand_wait_ready(mtd, 400);
+
+ led_trigger_event(nand_led_trigger, LED_FULL);
+ /* Wait until command is processed or timeout occurs */
+ do {
+ if (chip->dev_ready(mtd))
+ break;
+ touch_softlockup_watchdog();
+ } while (time_before(jiffies, timeo));
+ led_trigger_event(nand_led_trigger, LED_OFF);
+#else
u32 timeo = (CONFIG_SYS_HZ * 20) / 1000;
u32 time_start;
time_start = get_timer(0);
-
- /* wait until command is processed or timeout occures */
+ /* Wait until command is processed or timeout occurs */
while (get_timer(time_start) < timeo) {
if (chip->dev_ready)
if (chip->dev_ready(mtd))
break;
}
+#endif
}
+EXPORT_SYMBOL_GPL(nand_wait_ready);
/**
* nand_command - [DEFAULT] Send command to NAND device
- * @mtd: MTD device structure
- * @command: the command to be sent
- * @column: the column address for this command, -1 if none
- * @page_addr: the page address for this command, -1 if none
+ * @mtd: MTD device structure
+ * @command: the command to be sent
+ * @column: the column address for this command, -1 if none
+ * @page_addr: the page address for this command, -1 if none
*
- * Send command to NAND device. This function is used for small page
- * devices (256/512 Bytes per page)
+ * Send command to NAND device. This function is used for small page devices
+ * (512 Bytes per page).
*/
static void nand_command(struct mtd_info *mtd, unsigned int command,
int column, int page_addr)
int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE;
uint32_t rst_sts_cnt = CONFIG_SYS_NAND_RESET_CNT;
- /*
- * Write out the command to the device.
- */
+ /* Write out the command to the device */
if (command == NAND_CMD_SEQIN) {
int readcmd;
}
chip->cmd_ctrl(mtd, command, ctrl);
- /*
- * Address cycle, when necessary
- */
+ /* Address cycle, when necessary */
ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE;
/* Serially input address */
if (column != -1) {
/* Adjust columns for 16 bit buswidth */
- if (chip->options & NAND_BUSWIDTH_16)
+ if (chip->options & NAND_BUSWIDTH_16 &&
+ !nand_opcode_8bits(command))
column >>= 1;
chip->cmd_ctrl(mtd, column, ctrl);
ctrl &= ~NAND_CTRL_CHANGE;
chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/*
- * program and erase have their own busy handlers
- * status and sequential in needs no delay
+ * Program and erase have their own busy handlers status and sequential
+ * in needs no delay
*/
switch (command) {
return;
}
}
- /* Apply this short delay always to ensure that we do wait tWB in
- * any case on any machine. */
+ /*
+ * Apply this short delay always to ensure that we do wait tWB in
+ * any case on any machine.
+ */
ndelay(100);
nand_wait_ready(mtd);
/**
* nand_command_lp - [DEFAULT] Send command to NAND large page device
- * @mtd: MTD device structure
- * @command: the command to be sent
- * @column: the column address for this command, -1 if none
- * @page_addr: the page address for this command, -1 if none
+ * @mtd: MTD device structure
+ * @command: the command to be sent
+ * @column: the column address for this command, -1 if none
+ * @page_addr: the page address for this command, -1 if none
*
* Send command to NAND device. This is the version for the new large page
- * devices We dont have the separate regions as we have in the small page
- * devices. We must emulate NAND_CMD_READOOB to keep the code compatible.
+ * devices. We don't have the separate regions as we have in the small page
+ * devices. We must emulate NAND_CMD_READOOB to keep the code compatible.
*/
static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
int column, int page_addr)
}
/* Command latch cycle */
- chip->cmd_ctrl(mtd, command & 0xff,
- NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
+ chip->cmd_ctrl(mtd, command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
if (column != -1 || page_addr != -1) {
int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE;
/* Serially input address */
if (column != -1) {
/* Adjust columns for 16 bit buswidth */
- if (chip->options & NAND_BUSWIDTH_16)
+ if (chip->options & NAND_BUSWIDTH_16 &&
+ !nand_opcode_8bits(command))
column >>= 1;
chip->cmd_ctrl(mtd, column, ctrl);
ctrl &= ~NAND_CTRL_CHANGE;
chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/*
- * program and erase have their own busy handlers
- * status, sequential in, and deplete1 need no delay
+ * Program and erase have their own busy handlers status, sequential
+ * in, and deplete1 need no delay.
*/
switch (command) {
case NAND_CMD_SEQIN:
case NAND_CMD_RNDIN:
case NAND_CMD_STATUS:
- case NAND_CMD_DEPLETE1:
- return;
-
- /*
- * read error status commands require only a short delay
- */
- case NAND_CMD_STATUS_ERROR:
- case NAND_CMD_STATUS_ERROR0:
- case NAND_CMD_STATUS_ERROR1:
- case NAND_CMD_STATUS_ERROR2:
- case NAND_CMD_STATUS_ERROR3:
- udelay(chip->chip_delay);
return;
case NAND_CMD_RESET:
default:
/*
* If we don't have access to the busy pin, we apply the given
- * command delay
+ * command delay.
*/
if (!chip->dev_ready) {
udelay(chip->chip_delay);
}
}
- /* Apply this short delay always to ensure that we do wait tWB in
- * any case on any machine. */
+ /*
+ * Apply this short delay always to ensure that we do wait tWB in
+ * any case on any machine.
+ */
ndelay(100);
nand_wait_ready(mtd);
}
+/**
+ * panic_nand_get_device - [GENERIC] Get chip for selected access
+ * @chip: the nand chip descriptor
+ * @mtd: MTD device structure
+ * @new_state: the state which is requested
+ *
+ * Used when in panic, no locks are taken.
+ */
+static void panic_nand_get_device(struct nand_chip *chip,
+ struct mtd_info *mtd, int new_state)
+{
+ /* Hardware controller shared among independent devices */
+ chip->controller->active = chip;
+ chip->state = new_state;
+}
+
/**
* nand_get_device - [GENERIC] Get chip for selected access
- * @chip: the nand chip descriptor
- * @mtd: MTD device structure
- * @new_state: the state which is requested
+ * @mtd: MTD device structure
+ * @new_state: the state which is requested
*
* Get the device and lock it for exclusive access
*/
static int
-nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
+nand_get_device(struct mtd_info *mtd, int new_state)
{
+ struct nand_chip *chip = mtd->priv;
+#ifndef __UBOOT__
+ spinlock_t *lock = &chip->controller->lock;
+ wait_queue_head_t *wq = &chip->controller->wq;
+ DECLARE_WAITQUEUE(wait, current);
+retry:
+ spin_lock(lock);
+
+ /* Hardware controller shared among independent devices */
+ if (!chip->controller->active)
+ chip->controller->active = chip;
+
+ if (chip->controller->active == chip && chip->state == FL_READY) {
+ chip->state = new_state;
+ spin_unlock(lock);
+ return 0;
+ }
+ if (new_state == FL_PM_SUSPENDED) {
+ if (chip->controller->active->state == FL_PM_SUSPENDED) {
+ chip->state = FL_PM_SUSPENDED;
+ spin_unlock(lock);
+ return 0;
+ }
+ }
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ add_wait_queue(wq, &wait);
+ spin_unlock(lock);
+ schedule();
+ remove_wait_queue(wq, &wait);
+ goto retry;
+#else
chip->state = new_state;
return 0;
+#endif
}
/**
- * nand_wait - [DEFAULT] wait until the command is done
- * @mtd: MTD device structure
- * @chip: NAND chip structure
+ * panic_nand_wait - [GENERIC] wait until the command is done
+ * @mtd: MTD device structure
+ * @chip: NAND chip structure
+ * @timeo: timeout
*
- * Wait for command done. This applies to erase and program only
- * Erase can take up to 400ms and program up to 20ms according to
- * general NAND and SmartMedia specs
+ * Wait for command done. This is a helper function for nand_wait used when
+ * we are in interrupt context. May happen when in panic and trying to write
+ * an oops through mtdoops.
+ */
+static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip,
+ unsigned long timeo)
+{
+ int i;
+ for (i = 0; i < timeo; i++) {
+ if (chip->dev_ready) {
+ if (chip->dev_ready(mtd))
+ break;
+ } else {
+ if (chip->read_byte(mtd) & NAND_STATUS_READY)
+ break;
+ }
+ mdelay(1);
+ }
+}
+
+/**
+ * nand_wait - [DEFAULT] wait until the command is done
+ * @mtd: MTD device structure
+ * @chip: NAND chip structure
+ *
+ * Wait for command done. This applies to erase and program only. Erase can
+ * take up to 400ms and program up to 20ms according to general NAND and
+ * SmartMedia specs.
*/
static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
{
- unsigned long timeo;
- int state = chip->state;
- u32 time_start;
- if (state == FL_ERASING)
- timeo = (CONFIG_SYS_HZ * 400) / 1000;
- else
- timeo = (CONFIG_SYS_HZ * 20) / 1000;
+ int status, state = chip->state;
+ unsigned long timeo = (state == FL_ERASING ? 400 : 20);
- if ((state == FL_ERASING) && (chip->options & NAND_IS_AND))
- chip->cmdfunc(mtd, NAND_CMD_STATUS_MULTI, -1, -1);
- else
- chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
+ led_trigger_event(nand_led_trigger, LED_FULL);
- time_start = get_timer(0);
+ /*
+ * Apply this short delay always to ensure that we do wait tWB in any
+ * case on any machine.
+ */
+ ndelay(100);
- while (1) {
- if (get_timer(time_start) > timeo) {
- printf("Timeout!");
- return 0x01;
- }
+ chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
+#ifndef __UBOOT__
+ if (in_interrupt() || oops_in_progress)
+ panic_nand_wait(mtd, chip, timeo);
+ else {
+ timeo = jiffies + msecs_to_jiffies(timeo);
+ while (time_before(jiffies, timeo)) {
+ if (chip->dev_ready) {
+ if (chip->dev_ready(mtd))
+ break;
+ } else {
+ if (chip->read_byte(mtd) & NAND_STATUS_READY)
+ break;
+ }
+ cond_resched();
+ }
+ }
+#else
+ u32 timer = (CONFIG_SYS_HZ * timeo) / 1000;
+ u32 time_start;
+
+ time_start = get_timer(0);
+ while (get_timer(time_start) < timer) {
if (chip->dev_ready) {
if (chip->dev_ready(mtd))
break;
break;
}
}
+#endif
#ifdef PPCHAMELON_NAND_TIMER_HACK
time_start = get_timer(0);
while (get_timer(time_start) < 10)
;
#endif /* PPCHAMELON_NAND_TIMER_HACK */
+ led_trigger_event(nand_led_trigger, LED_OFF);
- return (int)chip->read_byte(mtd);
+ status = (int)chip->read_byte(mtd);
+ /* This can happen if in case of timeout or buggy dev_ready */
+ WARN_ON(!(status & NAND_STATUS_READY));
+ return status;
}
+#ifndef __UBOOT__
/**
- * nand_read_page_raw - [Intern] read raw page data without ecc
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- * @page: page number to read
+ * __nand_unlock - [REPLACEABLE] unlocks specified locked blocks
+ * @mtd: mtd info
+ * @ofs: offset to start unlock from
+ * @len: length to unlock
+ * @invert: when = 0, unlock the range of blocks within the lower and
+ * upper boundary address
+ * when = 1, unlock the range of blocks outside the boundaries
+ * of the lower and upper boundary address
*
- * Not for syndrome calculating ecc controllers, which use a special oob layout
+ * Returs unlock status.
*/
-static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf, int page)
+static int __nand_unlock(struct mtd_info *mtd, loff_t ofs,
+ uint64_t len, int invert)
{
- chip->read_buf(mtd, buf, mtd->writesize);
- chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
- return 0;
+ int ret = 0;
+ int status, page;
+ struct nand_chip *chip = mtd->priv;
+
+ /* Submit address of first page to unlock */
+ page = ofs >> chip->page_shift;
+ chip->cmdfunc(mtd, NAND_CMD_UNLOCK1, -1, page & chip->pagemask);
+
+ /* Submit address of last page to unlock */
+ page = (ofs + len) >> chip->page_shift;
+ chip->cmdfunc(mtd, NAND_CMD_UNLOCK2, -1,
+ (page | invert) & chip->pagemask);
+
+ /* Call wait ready function */
+ status = chip->waitfunc(mtd, chip);
+ /* See if device thinks it succeeded */
+ if (status & NAND_STATUS_FAIL) {
+ pr_debug("%s: error status = 0x%08x\n",
+ __func__, status);
+ ret = -EIO;
+ }
+
+ return ret;
}
/**
- * nand_read_page_raw_syndrome - [Intern] read raw page data without ecc
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- * @page: page number to read
+ * nand_unlock - [REPLACEABLE] unlocks specified locked blocks
+ * @mtd: mtd info
+ * @ofs: offset to start unlock from
+ * @len: length to unlock
*
- * We need a special oob layout and handling even when OOB isn't used.
+ * Returns unlock status.
*/
-static int nand_read_page_raw_syndrome(struct mtd_info *mtd,
- struct nand_chip *chip,
- uint8_t *buf, int page)
+int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
{
- int eccsize = chip->ecc.size;
- int eccbytes = chip->ecc.bytes;
- uint8_t *oob = chip->oob_poi;
- int steps, size;
+ int ret = 0;
+ int chipnr;
+ struct nand_chip *chip = mtd->priv;
- for (steps = chip->ecc.steps; steps > 0; steps--) {
- chip->read_buf(mtd, buf, eccsize);
- buf += eccsize;
+ pr_debug("%s: start = 0x%012llx, len = %llu\n",
+ __func__, (unsigned long long)ofs, len);
- if (chip->ecc.prepad) {
- chip->read_buf(mtd, oob, chip->ecc.prepad);
- oob += chip->ecc.prepad;
+ if (check_offs_len(mtd, ofs, len))
+ ret = -EINVAL;
+
+ /* Align to last block address if size addresses end of the device */
+ if (ofs + len == mtd->size)
+ len -= mtd->erasesize;
+
+ nand_get_device(mtd, FL_UNLOCKING);
+
+ /* Shift to get chip number */
+ chipnr = ofs >> chip->chip_shift;
+
+ chip->select_chip(mtd, chipnr);
+
+ /* Check, if it is write protected */
+ if (nand_check_wp(mtd)) {
+ pr_debug("%s: device is write protected!\n",
+ __func__);
+ ret = -EIO;
+ goto out;
+ }
+
+ ret = __nand_unlock(mtd, ofs, len, 0);
+
+out:
+ chip->select_chip(mtd, -1);
+ nand_release_device(mtd);
+
+ return ret;
+}
+EXPORT_SYMBOL(nand_unlock);
+
+/**
+ * nand_lock - [REPLACEABLE] locks all blocks present in the device
+ * @mtd: mtd info
+ * @ofs: offset to start unlock from
+ * @len: length to unlock
+ *
+ * This feature is not supported in many NAND parts. 'Micron' NAND parts do
+ * have this feature, but it allows only to lock all blocks, not for specified
+ * range for block. Implementing 'lock' feature by making use of 'unlock', for
+ * now.
+ *
+ * Returns lock status.
+ */
+int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+ int ret = 0;
+ int chipnr, status, page;
+ struct nand_chip *chip = mtd->priv;
+
+ pr_debug("%s: start = 0x%012llx, len = %llu\n",
+ __func__, (unsigned long long)ofs, len);
+
+ if (check_offs_len(mtd, ofs, len))
+ ret = -EINVAL;
+
+ nand_get_device(mtd, FL_LOCKING);
+
+ /* Shift to get chip number */
+ chipnr = ofs >> chip->chip_shift;
+
+ chip->select_chip(mtd, chipnr);
+
+ /* Check, if it is write protected */
+ if (nand_check_wp(mtd)) {
+ pr_debug("%s: device is write protected!\n",
+ __func__);
+ status = MTD_ERASE_FAILED;
+ ret = -EIO;
+ goto out;
+ }
+
+ /* Submit address of first page to lock */
+ page = ofs >> chip->page_shift;
+ chip->cmdfunc(mtd, NAND_CMD_LOCK, -1, page & chip->pagemask);
+
+ /* Call wait ready function */
+ status = chip->waitfunc(mtd, chip);
+ /* See if device thinks it succeeded */
+ if (status & NAND_STATUS_FAIL) {
+ pr_debug("%s: error status = 0x%08x\n",
+ __func__, status);
+ ret = -EIO;
+ goto out;
+ }
+
+ ret = __nand_unlock(mtd, ofs, len, 0x1);
+
+out:
+ chip->select_chip(mtd, -1);
+ nand_release_device(mtd);
+
+ return ret;
+}
+EXPORT_SYMBOL(nand_lock);
+#endif
+
+/**
+ * nand_read_page_raw - [INTERN] read raw page data without ecc
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * Not for syndrome calculating ECC controllers, which use a special oob layout.
+ */
+static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ chip->read_buf(mtd, buf, mtd->writesize);
+ if (oob_required)
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ return 0;
+}
+
+/**
+ * nand_read_page_raw_syndrome - [INTERN] read raw page data without ecc
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * We need a special oob layout and handling even when OOB isn't used.
+ */
+static int nand_read_page_raw_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf,
+ int oob_required, int page)
+{
+ int eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ uint8_t *oob = chip->oob_poi;
+ int steps, size;
+
+ for (steps = chip->ecc.steps; steps > 0; steps--) {
+ chip->read_buf(mtd, buf, eccsize);
+ buf += eccsize;
+
+ if (chip->ecc.prepad) {
+ chip->read_buf(mtd, oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
}
chip->read_buf(mtd, oob, eccbytes);
}
/**
- * nand_read_page_swecc - [REPLACABLE] software ecc based page read function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- * @page: page number to read
+ * nand_read_page_swecc - [REPLACEABLE] software ECC based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
*/
static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf, int page)
+ uint8_t *buf, int oob_required, int page)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
uint8_t *ecc_calc = chip->buffers->ecccalc;
uint8_t *ecc_code = chip->buffers->ecccode;
uint32_t *eccpos = chip->ecc.layout->eccpos;
+ unsigned int max_bitflips = 0;
- chip->ecc.read_page_raw(mtd, chip, buf, page);
+ chip->ecc.read_page_raw(mtd, chip, buf, 1, page);
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
chip->ecc.calculate(mtd, p, &ecc_calc[i]);
int stat;
stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
- if (stat < 0)
+ if (stat < 0) {
mtd->ecc_stats.failed++;
- else
+ } else {
mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
}
- return 0;
+ return max_bitflips;
}
/**
- * nand_read_subpage - [REPLACABLE] software ecc based sub-page read function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @data_offs: offset of requested data within the page
- * @readlen: data length
- * @bufpoi: buffer to store read data
+ * nand_read_subpage - [REPLACEABLE] ECC based sub-page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @data_offs: offset of requested data within the page
+ * @readlen: data length
+ * @bufpoi: buffer to store read data
+ * @page: page number to read
*/
static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
- uint32_t data_offs, uint32_t readlen, uint8_t *bufpoi)
+ uint32_t data_offs, uint32_t readlen, uint8_t *bufpoi,
+ int page)
{
int start_step, end_step, num_steps;
uint32_t *eccpos = chip->ecc.layout->eccpos;
int data_col_addr, i, gaps = 0;
int datafrag_len, eccfrag_len, aligned_len, aligned_pos;
int busw = (chip->options & NAND_BUSWIDTH_16) ? 2 : 1;
- int index = 0;
+ int index;
+ unsigned int max_bitflips = 0;
- /* Column address wihin the page aligned to ECC size (256bytes). */
+ /* Column address within the page aligned to ECC size (256bytes) */
start_step = data_offs / chip->ecc.size;
end_step = (data_offs + readlen - 1) / chip->ecc.size;
num_steps = end_step - start_step + 1;
+ index = start_step * chip->ecc.bytes;
- /* Data size aligned to ECC ecc.size*/
+ /* Data size aligned to ECC ecc.size */
datafrag_len = num_steps * chip->ecc.size;
eccfrag_len = num_steps * chip->ecc.bytes;
p = bufpoi + data_col_addr;
chip->read_buf(mtd, p, datafrag_len);
- /* Calculate ECC */
+ /* Calculate ECC */
for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size)
chip->ecc.calculate(mtd, p, &chip->buffers->ecccalc[i]);
- /* The performance is faster if to position offsets
- according to ecc.pos. Let make sure here that
- there are no gaps in ecc positions */
+ /*
+ * The performance is faster if we position offsets according to
+ * ecc.pos. Let's make sure that there are no gaps in ECC positions.
+ */
for (i = 0; i < eccfrag_len - 1; i++) {
if (eccpos[i + start_step * chip->ecc.bytes] + 1 !=
eccpos[i + start_step * chip->ecc.bytes + 1]) {
chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1);
chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
} else {
- /* send the command to read the particular ecc bytes */
- /* take care about buswidth alignment in read_buf */
- index = start_step * chip->ecc.bytes;
-
+ /*
+ * Send the command to read the particular ECC bytes take care
+ * about buswidth alignment in read_buf.
+ */
aligned_pos = eccpos[index] & ~(busw - 1);
aligned_len = eccfrag_len;
if (eccpos[index] & (busw - 1))
stat = chip->ecc.correct(mtd, p,
&chip->buffers->ecccode[i], &chip->buffers->ecccalc[i]);
- if (stat < 0)
+ if (stat < 0) {
mtd->ecc_stats.failed++;
- else
+ } else {
mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
}
- return 0;
+ return max_bitflips;
}
/**
- * nand_read_page_hwecc - [REPLACABLE] hardware ecc based page read function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- * @page: page number to read
+ * nand_read_page_hwecc - [REPLACEABLE] hardware ECC based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
*
- * Not for syndrome calculating ecc controllers which need a special oob layout
+ * Not for syndrome calculating ECC controllers which need a special oob layout.
*/
static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf, int page)
+ uint8_t *buf, int oob_required, int page)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
uint8_t *ecc_calc = chip->buffers->ecccalc;
uint8_t *ecc_code = chip->buffers->ecccode;
uint32_t *eccpos = chip->ecc.layout->eccpos;
+ unsigned int max_bitflips = 0;
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
chip->ecc.hwctl(mtd, NAND_ECC_READ);
int stat;
stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
- if (stat < 0)
+ if (stat < 0) {
mtd->ecc_stats.failed++;
- else
+ } else {
mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
}
- return 0;
+ return max_bitflips;
}
/**
- * nand_read_page_hwecc_oob_first - [REPLACABLE] hw ecc, read oob first
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- * @page: page number to read
+ * nand_read_page_hwecc_oob_first - [REPLACEABLE] hw ecc, read oob first
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
*
- * Hardware ECC for large page chips, require OOB to be read first.
- * For this ECC mode, the write_page method is re-used from ECC_HW.
- * These methods read/write ECC from the OOB area, unlike the
- * ECC_HW_SYNDROME support with multiple ECC steps, follows the
- * "infix ECC" scheme and reads/writes ECC from the data area, by
- * overwriting the NAND manufacturer bad block markings.
+ * Hardware ECC for large page chips, require OOB to be read first. For this
+ * ECC mode, the write_page method is re-used from ECC_HW. These methods
+ * read/write ECC from the OOB area, unlike the ECC_HW_SYNDROME support with
+ * multiple ECC steps, follows the "infix ECC" scheme and reads/writes ECC from
+ * the data area, by overwriting the NAND manufacturer bad block markings.
*/
static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd,
- struct nand_chip *chip, uint8_t *buf, int page)
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
uint8_t *ecc_code = chip->buffers->ecccode;
uint32_t *eccpos = chip->ecc.layout->eccpos;
uint8_t *ecc_calc = chip->buffers->ecccalc;
+ unsigned int max_bitflips = 0;
/* Read the OOB area first */
chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
chip->ecc.calculate(mtd, p, &ecc_calc[i]);
stat = chip->ecc.correct(mtd, p, &ecc_code[i], NULL);
- if (stat < 0)
+ if (stat < 0) {
mtd->ecc_stats.failed++;
- else
+ } else {
mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
}
- return 0;
+ return max_bitflips;
}
/**
- * nand_read_page_syndrome - [REPLACABLE] hardware ecc syndrom based page read
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- * @page: page number to read
+ * nand_read_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page read
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
*
- * The hw generator calculates the error syndrome automatically. Therefor
- * we need a special oob layout and handling.
+ * The hw generator calculates the error syndrome automatically. Therefore we
+ * need a special oob layout and handling.
*/
static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf, int page)
+ uint8_t *buf, int oob_required, int page)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
int eccsteps = chip->ecc.steps;
uint8_t *p = buf;
uint8_t *oob = chip->oob_poi;
+ unsigned int max_bitflips = 0;
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
int stat;
chip->read_buf(mtd, oob, eccbytes);
stat = chip->ecc.correct(mtd, p, oob, NULL);
- if (stat < 0)
+ if (stat < 0) {
mtd->ecc_stats.failed++;
- else
+ } else {
mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
oob += eccbytes;
if (i)
chip->read_buf(mtd, oob, i);
- return 0;
+ return max_bitflips;
}
/**
- * nand_transfer_oob - [Internal] Transfer oob to client buffer
- * @chip: nand chip structure
- * @oob: oob destination address
- * @ops: oob ops structure
- * @len: size of oob to transfer
+ * nand_transfer_oob - [INTERN] Transfer oob to client buffer
+ * @chip: nand chip structure
+ * @oob: oob destination address
+ * @ops: oob ops structure
+ * @len: size of oob to transfer
*/
static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob,
struct mtd_oob_ops *ops, size_t len)
{
switch (ops->mode) {
- case MTD_OOB_PLACE:
- case MTD_OOB_RAW:
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_RAW:
memcpy(oob, chip->oob_poi + ops->ooboffs, len);
return oob + len;
- case MTD_OOB_AUTO: {
+ case MTD_OPS_AUTO_OOB: {
struct nand_oobfree *free = chip->ecc.layout->oobfree;
uint32_t boffs = 0, roffs = ops->ooboffs;
size_t bytes = 0;
for (; free->length && len; free++, len -= bytes) {
- /* Read request not from offset 0 ? */
+ /* Read request not from offset 0? */
if (unlikely(roffs)) {
if (roffs >= free->length) {
roffs -= free->length;
}
/**
- * nand_do_read_ops - [Internal] Read data with ECC
+ * nand_setup_read_retry - [INTERN] Set the READ RETRY mode
+ * @mtd: MTD device structure
+ * @retry_mode: the retry mode to use
*
- * @mtd: MTD device structure
- * @from: offset to read from
- * @ops: oob ops structure
+ * Some vendors supply a special command to shift the Vt threshold, to be used
+ * when there are too many bitflips in a page (i.e., ECC error). After setting
+ * a new threshold, the host should retry reading the page.
+ */
+static int nand_setup_read_retry(struct mtd_info *mtd, int retry_mode)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ pr_debug("setting READ RETRY mode %d\n", retry_mode);
+
+ if (retry_mode >= chip->read_retries)
+ return -EINVAL;
+
+ if (!chip->setup_read_retry)
+ return -EOPNOTSUPP;
+
+ return chip->setup_read_retry(mtd, retry_mode);
+}
+
+/**
+ * nand_do_read_ops - [INTERN] Read data with ECC
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob ops structure
*
* Internal function. Called with chip held.
*/
static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
struct mtd_oob_ops *ops)
{
- int chipnr, page, realpage, col, bytes, aligned;
+ int chipnr, page, realpage, col, bytes, aligned, oob_required;
struct nand_chip *chip = mtd->priv;
- struct mtd_ecc_stats stats;
- int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
- int sndcmd = 1;
int ret = 0;
uint32_t readlen = ops->len;
uint32_t oobreadlen = ops->ooblen;
- uint32_t max_oobsize = ops->mode == MTD_OOB_AUTO ?
+ uint32_t max_oobsize = ops->mode == MTD_OPS_AUTO_OOB ?
mtd->oobavail : mtd->oobsize;
uint8_t *bufpoi, *oob, *buf;
-
- stats = mtd->ecc_stats;
+ unsigned int max_bitflips = 0;
+ int retry_mode = 0;
+ bool ecc_fail = false;
chipnr = (int)(from >> chip->chip_shift);
chip->select_chip(mtd, chipnr);
buf = ops->datbuf;
oob = ops->oobbuf;
+ oob_required = oob ? 1 : 0;
while (1) {
- WATCHDOG_RESET();
+ unsigned int ecc_failures = mtd->ecc_stats.failed;
+ WATCHDOG_RESET();
bytes = min(mtd->writesize - col, readlen);
aligned = (bytes == mtd->writesize);
- /* Is the current page in the buffer ? */
+ /* Is the current page in the buffer? */
if (realpage != chip->pagebuf || oob) {
bufpoi = aligned ? buf : chip->buffers->databuf;
- if (likely(sndcmd)) {
- chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
- sndcmd = 0;
- }
+read_retry:
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
- /* Now read the page into the buffer */
- if (unlikely(ops->mode == MTD_OOB_RAW))
- ret = chip->ecc.read_page_raw(mtd, chip,
- bufpoi, page);
+ /*
+ * Now read the page into the buffer. Absent an error,
+ * the read methods return max bitflips per ecc step.
+ */
+ if (unlikely(ops->mode == MTD_OPS_RAW))
+ ret = chip->ecc.read_page_raw(mtd, chip, bufpoi,
+ oob_required,
+ page);
else if (!aligned && NAND_HAS_SUBPAGE_READ(chip) &&
- !oob)
+ !oob)
ret = chip->ecc.read_subpage(mtd, chip,
- col, bytes, bufpoi);
+ col, bytes, bufpoi,
+ page);
else
ret = chip->ecc.read_page(mtd, chip, bufpoi,
- page);
- if (ret < 0)
+ oob_required, page);
+ if (ret < 0) {
+ if (!aligned)
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
break;
+ }
+
+ max_bitflips = max_t(unsigned int, max_bitflips, ret);
/* Transfer not aligned data */
if (!aligned) {
if (!NAND_HAS_SUBPAGE_READ(chip) && !oob &&
- !(mtd->ecc_stats.failed - stats.failed))
+ !(mtd->ecc_stats.failed - ecc_failures) &&
+ (ops->mode != MTD_OPS_RAW)) {
chip->pagebuf = realpage;
+ chip->pagebuf_bitflips = ret;
+ } else {
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+ }
memcpy(buf, chip->buffers->databuf + col, bytes);
}
- buf += bytes;
-
if (unlikely(oob)) {
-
int toread = min(oobreadlen, max_oobsize);
if (toread) {
}
}
- if (!(chip->options & NAND_NO_READRDY)) {
- /*
- * Apply delay or wait for ready/busy pin. Do
- * this before the AUTOINCR check, so no
- * problems arise if a chip which does auto
- * increment is marked as NOAUTOINCR by the
- * board driver.
- */
+ if (chip->options & NAND_NEED_READRDY) {
+ /* Apply delay or wait for ready/busy pin */
if (!chip->dev_ready)
udelay(chip->chip_delay);
else
nand_wait_ready(mtd);
}
+
+ if (mtd->ecc_stats.failed - ecc_failures) {
+ if (retry_mode + 1 < chip->read_retries) {
+ retry_mode++;
+ ret = nand_setup_read_retry(mtd,
+ retry_mode);
+ if (ret < 0)
+ break;
+
+ /* Reset failures; retry */
+ mtd->ecc_stats.failed = ecc_failures;
+ goto read_retry;
+ } else {
+ /* No more retry modes; real failure */
+ ecc_fail = true;
+ }
+ }
+
+ buf += bytes;
} else {
memcpy(buf, chip->buffers->databuf + col, bytes);
buf += bytes;
+ max_bitflips = max_t(unsigned int, max_bitflips,
+ chip->pagebuf_bitflips);
}
readlen -= bytes;
+ /* Reset to retry mode 0 */
+ if (retry_mode) {
+ ret = nand_setup_read_retry(mtd, 0);
+ if (ret < 0)
+ break;
+ retry_mode = 0;
+ }
+
if (!readlen)
break;
- /* For subsequent reads align to page boundary. */
+ /* For subsequent reads align to page boundary */
col = 0;
/* Increment page address */
realpage++;
chip->select_chip(mtd, -1);
chip->select_chip(mtd, chipnr);
}
-
- /* Check, if the chip supports auto page increment
- * or if we have hit a block boundary.
- */
- if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
- sndcmd = 1;
}
+ chip->select_chip(mtd, -1);
ops->retlen = ops->len - (size_t) readlen;
if (oob)
ops->oobretlen = ops->ooblen - oobreadlen;
- if (ret)
+ if (ret < 0)
return ret;
- if (mtd->ecc_stats.failed - stats.failed)
+ if (ecc_fail)
return -EBADMSG;
- return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0;
+ return max_bitflips;
}
/**
* nand_read - [MTD Interface] MTD compatibility function for nand_do_read_ecc
- * @mtd: MTD device structure
- * @from: offset to read from
- * @len: number of bytes to read
- * @retlen: pointer to variable to store the number of read bytes
- * @buf: the databuffer to put data
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @len: number of bytes to read
+ * @retlen: pointer to variable to store the number of read bytes
+ * @buf: the databuffer to put data
*
- * Get hold of the chip and call nand_do_read
+ * Get hold of the chip and call nand_do_read.
*/
static int nand_read(struct mtd_info *mtd, loff_t from, size_t len,
size_t *retlen, uint8_t *buf)
{
- struct nand_chip *chip = mtd->priv;
+ struct mtd_oob_ops ops;
int ret;
- /* Do not allow reads past end of device */
- if ((from + len) > mtd->size)
- return -EINVAL;
- if (!len)
- return 0;
-
- nand_get_device(chip, mtd, FL_READING);
-
- chip->ops.len = len;
- chip->ops.datbuf = buf;
- chip->ops.oobbuf = NULL;
-
- ret = nand_do_read_ops(mtd, from, &chip->ops);
-
- *retlen = chip->ops.retlen;
-
+ nand_get_device(mtd, FL_READING);
+ ops.len = len;
+ ops.datbuf = buf;
+ ops.oobbuf = NULL;
+ ops.mode = MTD_OPS_PLACE_OOB;
+ ret = nand_do_read_ops(mtd, from, &ops);
+ *retlen = ops.retlen;
nand_release_device(mtd);
-
return ret;
}
/**
- * nand_read_oob_std - [REPLACABLE] the most common OOB data read function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to read
- * @sndcmd: flag whether to issue read command or not
+ * nand_read_oob_std - [REPLACEABLE] the most common OOB data read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to read
*/
static int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
- int page, int sndcmd)
+ int page)
{
- if (sndcmd) {
- chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
- sndcmd = 0;
- }
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
- return sndcmd;
+ return 0;
}
/**
- * nand_read_oob_syndrome - [REPLACABLE] OOB data read function for HW ECC
+ * nand_read_oob_syndrome - [REPLACEABLE] OOB data read function for HW ECC
* with syndromes
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to read
- * @sndcmd: flag whether to issue read command or not
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to read
*/
static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
- int page, int sndcmd)
+ int page)
{
uint8_t *buf = chip->oob_poi;
int length = mtd->oobsize;
if (length > 0)
chip->read_buf(mtd, bufpoi, length);
- return 1;
+ return 0;
}
/**
- * nand_write_oob_std - [REPLACABLE] the most common OOB data write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to write
+ * nand_write_oob_std - [REPLACEABLE] the most common OOB data write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to write
*/
static int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
int page)
}
/**
- * nand_write_oob_syndrome - [REPLACABLE] OOB data write function for HW ECC
- * with syndrome - only for large page flash !
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to write
+ * nand_write_oob_syndrome - [REPLACEABLE] OOB data write function for HW ECC
+ * with syndrome - only for large page flash
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to write
*/
static int nand_write_oob_syndrome(struct mtd_info *mtd,
struct nand_chip *chip, int page)
}
/**
- * nand_do_read_oob - [Intern] NAND read out-of-band
- * @mtd: MTD device structure
- * @from: offset to read from
- * @ops: oob operations description structure
+ * nand_do_read_oob - [INTERN] NAND read out-of-band
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operations description structure
*
- * NAND read out-of-band data from the spare area
+ * NAND read out-of-band data from the spare area.
*/
static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
struct mtd_oob_ops *ops)
{
- int page, realpage, chipnr, sndcmd = 1;
+ int page, realpage, chipnr;
struct nand_chip *chip = mtd->priv;
- int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
+ struct mtd_ecc_stats stats;
int readlen = ops->ooblen;
int len;
uint8_t *buf = ops->oobbuf;
+ int ret = 0;
- MTDDEBUG(MTD_DEBUG_LEVEL3, "%s: from = 0x%08Lx, len = %i\n",
+ pr_debug("%s: from = 0x%08Lx, len = %i\n",
__func__, (unsigned long long)from, readlen);
- if (ops->mode == MTD_OOB_AUTO)
+ stats = mtd->ecc_stats;
+
+ if (ops->mode == MTD_OPS_AUTO_OOB)
len = chip->ecc.layout->oobavail;
else
len = mtd->oobsize;
if (unlikely(ops->ooboffs >= len)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt to start read "
- "outside oob\n", __func__);
+ pr_debug("%s: attempt to start read outside oob\n",
+ __func__);
return -EINVAL;
}
if (unlikely(from >= mtd->size ||
ops->ooboffs + readlen > ((mtd->size >> chip->page_shift) -
(from >> chip->page_shift)) * len)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt read beyond end "
- "of device\n", __func__);
+ pr_debug("%s: attempt to read beyond end of device\n",
+ __func__);
return -EINVAL;
}
while (1) {
WATCHDOG_RESET();
- sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd);
+
+ if (ops->mode == MTD_OPS_RAW)
+ ret = chip->ecc.read_oob_raw(mtd, chip, page);
+ else
+ ret = chip->ecc.read_oob(mtd, chip, page);
+
+ if (ret < 0)
+ break;
len = min(len, readlen);
buf = nand_transfer_oob(chip, buf, ops, len);
- if (!(chip->options & NAND_NO_READRDY)) {
- /*
- * Apply delay or wait for ready/busy pin. Do this
- * before the AUTOINCR check, so no problems arise if a
- * chip which does auto increment is marked as
- * NOAUTOINCR by the board driver.
- */
+ if (chip->options & NAND_NEED_READRDY) {
+ /* Apply delay or wait for ready/busy pin */
if (!chip->dev_ready)
udelay(chip->chip_delay);
else
chip->select_chip(mtd, -1);
chip->select_chip(mtd, chipnr);
}
-
- /* Check, if the chip supports auto page increment
- * or if we have hit a block boundary.
- */
- if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
- sndcmd = 1;
}
+ chip->select_chip(mtd, -1);
- ops->oobretlen = ops->ooblen;
- return 0;
+ ops->oobretlen = ops->ooblen - readlen;
+
+ if (ret < 0)
+ return ret;
+
+ if (mtd->ecc_stats.failed - stats.failed)
+ return -EBADMSG;
+
+ return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0;
}
/**
* nand_read_oob - [MTD Interface] NAND read data and/or out-of-band
- * @mtd: MTD device structure
- * @from: offset to read from
- * @ops: oob operation description structure
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operation description structure
*
- * NAND read data and/or out-of-band data
+ * NAND read data and/or out-of-band data.
*/
static int nand_read_oob(struct mtd_info *mtd, loff_t from,
struct mtd_oob_ops *ops)
{
- struct nand_chip *chip = mtd->priv;
int ret = -ENOTSUPP;
ops->retlen = 0;
/* Do not allow reads past end of device */
if (ops->datbuf && (from + ops->len) > mtd->size) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt read "
- "beyond end of device\n", __func__);
+ pr_debug("%s: attempt to read beyond end of device\n",
+ __func__);
return -EINVAL;
}
- nand_get_device(chip, mtd, FL_READING);
+ nand_get_device(mtd, FL_READING);
switch (ops->mode) {
- case MTD_OOB_PLACE:
- case MTD_OOB_AUTO:
- case MTD_OOB_RAW:
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_AUTO_OOB:
+ case MTD_OPS_RAW:
break;
default:
/**
- * nand_write_page_raw - [Intern] raw page write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
+ * nand_write_page_raw - [INTERN] raw page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
*
- * Not for syndrome calculating ecc controllers, which use a special oob layout
+ * Not for syndrome calculating ECC controllers, which use a special oob layout.
*/
-static void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf)
+static int nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
{
chip->write_buf(mtd, buf, mtd->writesize);
- chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+ if (oob_required)
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
}
/**
- * nand_write_page_raw_syndrome - [Intern] raw page write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
+ * nand_write_page_raw_syndrome - [INTERN] raw page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
*
* We need a special oob layout and handling even when ECC isn't checked.
*/
-static void nand_write_page_raw_syndrome(struct mtd_info *mtd,
+static int nand_write_page_raw_syndrome(struct mtd_info *mtd,
struct nand_chip *chip,
- const uint8_t *buf)
+ const uint8_t *buf, int oob_required)
{
int eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
oob += chip->ecc.prepad;
}
- chip->read_buf(mtd, oob, eccbytes);
+ chip->write_buf(mtd, oob, eccbytes);
oob += eccbytes;
if (chip->ecc.postpad) {
size = mtd->oobsize - (oob - chip->oob_poi);
if (size)
chip->write_buf(mtd, oob, size);
+
+ return 0;
}
/**
- * nand_write_page_swecc - [REPLACABLE] software ecc based page write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
+ * nand_write_page_swecc - [REPLACEABLE] software ECC based page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
*/
-static void nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf)
+static int nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
const uint8_t *p = buf;
uint32_t *eccpos = chip->ecc.layout->eccpos;
- /* Software ecc calculation */
+ /* Software ECC calculation */
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
chip->ecc.calculate(mtd, p, &ecc_calc[i]);
for (i = 0; i < chip->ecc.total; i++)
chip->oob_poi[eccpos[i]] = ecc_calc[i];
- chip->ecc.write_page_raw(mtd, chip, buf);
+ return chip->ecc.write_page_raw(mtd, chip, buf, 1);
}
/**
- * nand_write_page_hwecc - [REPLACABLE] hardware ecc based page write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
+ * nand_write_page_hwecc - [REPLACEABLE] hardware ECC based page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
*/
-static void nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf)
+static int nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
chip->oob_poi[eccpos[i]] = ecc_calc[i];
chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
}
+
/**
- * nand_write_page_syndrome - [REPLACABLE] hardware ecc syndrom based page write
+ * nand_write_subpage_hwecc - [REPLACABLE] hardware ECC based subpage write
* @mtd: mtd info structure
* @chip: nand chip info structure
+ * @offset: column address of subpage within the page
+ * @data_len: data length
* @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
+ */
+static int nand_write_subpage_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint32_t offset,
+ uint32_t data_len, const uint8_t *buf,
+ int oob_required)
+{
+ uint8_t *oob_buf = chip->oob_poi;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ int ecc_steps = chip->ecc.steps;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint32_t start_step = offset / ecc_size;
+ uint32_t end_step = (offset + data_len - 1) / ecc_size;
+ int oob_bytes = mtd->oobsize / ecc_steps;
+ int step, i;
+
+ for (step = 0; step < ecc_steps; step++) {
+ /* configure controller for WRITE access */
+ chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+
+ /* write data (untouched subpages already masked by 0xFF) */
+ chip->write_buf(mtd, buf, ecc_size);
+
+ /* mask ECC of un-touched subpages by padding 0xFF */
+ if ((step < start_step) || (step > end_step))
+ memset(ecc_calc, 0xff, ecc_bytes);
+ else
+ chip->ecc.calculate(mtd, buf, ecc_calc);
+
+ /* mask OOB of un-touched subpages by padding 0xFF */
+ /* if oob_required, preserve OOB metadata of written subpage */
+ if (!oob_required || (step < start_step) || (step > end_step))
+ memset(oob_buf, 0xff, oob_bytes);
+
+ buf += ecc_size;
+ ecc_calc += ecc_bytes;
+ oob_buf += oob_bytes;
+ }
+
+ /* copy calculated ECC for whole page to chip->buffer->oob */
+ /* this include masked-value(0xFF) for unwritten subpages */
+ ecc_calc = chip->buffers->ecccalc;
+ for (i = 0; i < chip->ecc.total; i++)
+ chip->oob_poi[eccpos[i]] = ecc_calc[i];
+
+ /* write OOB buffer to NAND device */
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
+}
+
+
+/**
+ * nand_write_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page write
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
*
- * The hw generator calculates the error syndrome automatically. Therefor
- * we need a special oob layout and handling.
+ * The hw generator calculates the error syndrome automatically. Therefore we
+ * need a special oob layout and handling.
*/
-static void nand_write_page_syndrome(struct mtd_info *mtd,
- struct nand_chip *chip, const uint8_t *buf)
+static int nand_write_page_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
i = mtd->oobsize - (oob - chip->oob_poi);
if (i)
chip->write_buf(mtd, oob, i);
+
+ return 0;
}
/**
* nand_write_page - [REPLACEABLE] write one page
- * @mtd: MTD device structure
- * @chip: NAND chip descriptor
- * @buf: the data to write
- * @page: page number to write
- * @cached: cached programming
- * @raw: use _raw version of write_page
+ * @mtd: MTD device structure
+ * @chip: NAND chip descriptor
+ * @offset: address offset within the page
+ * @data_len: length of actual data to be written
+ * @buf: the data to write
+ * @oob_required: must write chip->oob_poi to OOB
+ * @page: page number to write
+ * @cached: cached programming
+ * @raw: use _raw version of write_page
*/
static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, int page, int cached, int raw)
+ uint32_t offset, int data_len, const uint8_t *buf,
+ int oob_required, int page, int cached, int raw)
{
- int status;
+ int status, subpage;
+
+ if (!(chip->options & NAND_NO_SUBPAGE_WRITE) &&
+ chip->ecc.write_subpage)
+ subpage = offset || (data_len < mtd->writesize);
+ else
+ subpage = 0;
chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
if (unlikely(raw))
- chip->ecc.write_page_raw(mtd, chip, buf);
+ status = chip->ecc.write_page_raw(mtd, chip, buf,
+ oob_required);
+ else if (subpage)
+ status = chip->ecc.write_subpage(mtd, chip, offset, data_len,
+ buf, oob_required);
else
- chip->ecc.write_page(mtd, chip, buf);
+ status = chip->ecc.write_page(mtd, chip, buf, oob_required);
+
+ if (status < 0)
+ return status;
/*
- * Cached progamming disabled for now, Not sure if its worth the
- * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s)
+ * Cached progamming disabled for now. Not sure if it's worth the
+ * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s).
*/
cached = 0;
- if (!cached || !(chip->options & NAND_CACHEPRG)) {
+ if (!cached || !NAND_HAS_CACHEPROG(chip)) {
chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
status = chip->waitfunc(mtd, chip);
/*
* See if operation failed and additional status checks are
- * available
+ * available.
*/
if ((status & NAND_STATUS_FAIL) && (chip->errstat))
status = chip->errstat(mtd, chip, FL_WRITING, status,
status = chip->waitfunc(mtd, chip);
}
-#ifdef CONFIG_MTD_NAND_VERIFY_WRITE
+
+#ifdef __UBOOT__
+#if defined(CONFIG_MTD_NAND_VERIFY_WRITE)
/* Send command to read back the data */
chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
if (chip->verify_buf(mtd, buf, mtd->writesize))
return -EIO;
+
+ /* Make sure the next page prog is preceded by a status read */
+ chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
#endif
+#endif
+
return 0;
}
/**
- * nand_fill_oob - [Internal] Transfer client buffer to oob
- * @chip: nand chip structure
- * @oob: oob data buffer
- * @len: oob data write length
- * @ops: oob ops structure
+ * nand_fill_oob - [INTERN] Transfer client buffer to oob
+ * @mtd: MTD device structure
+ * @oob: oob data buffer
+ * @len: oob data write length
+ * @ops: oob ops structure
*/
-static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, size_t len,
- struct mtd_oob_ops *ops)
+static uint8_t *nand_fill_oob(struct mtd_info *mtd, uint8_t *oob, size_t len,
+ struct mtd_oob_ops *ops)
{
+ struct nand_chip *chip = mtd->priv;
+
+ /*
+ * Initialise to all 0xFF, to avoid the possibility of left over OOB
+ * data from a previous OOB read.
+ */
+ memset(chip->oob_poi, 0xff, mtd->oobsize);
+
switch (ops->mode) {
- case MTD_OOB_PLACE:
- case MTD_OOB_RAW:
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_RAW:
memcpy(chip->oob_poi + ops->ooboffs, oob, len);
return oob + len;
- case MTD_OOB_AUTO: {
+ case MTD_OPS_AUTO_OOB: {
struct nand_oobfree *free = chip->ecc.layout->oobfree;
uint32_t boffs = 0, woffs = ops->ooboffs;
size_t bytes = 0;
for (; free->length && len; free++, len -= bytes) {
- /* Write request not from offset 0 ? */
+ /* Write request not from offset 0? */
if (unlikely(woffs)) {
if (woffs >= free->length) {
woffs -= free->length;
#define NOTALIGNED(x) ((x & (chip->subpagesize - 1)) != 0)
/**
- * nand_do_write_ops - [Internal] NAND write with ECC
- * @mtd: MTD device structure
- * @to: offset to write to
- * @ops: oob operations description structure
+ * nand_do_write_ops - [INTERN] NAND write with ECC
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operations description structure
*
- * NAND write with ECC
+ * NAND write with ECC.
*/
static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
struct mtd_oob_ops *ops)
uint32_t writelen = ops->len;
uint32_t oobwritelen = ops->ooblen;
- uint32_t oobmaxlen = ops->mode == MTD_OOB_AUTO ?
+ uint32_t oobmaxlen = ops->mode == MTD_OPS_AUTO_OOB ?
mtd->oobavail : mtd->oobsize;
uint8_t *oob = ops->oobbuf;
uint8_t *buf = ops->datbuf;
- int ret, subpage;
+ int ret;
+ int oob_required = oob ? 1 : 0;
ops->retlen = 0;
if (!writelen)
return 0;
- column = to & (mtd->writesize - 1);
- subpage = column || (writelen & (mtd->writesize - 1));
-
- if (subpage && oob)
+#ifndef __UBOOT__
+ /* Reject writes, which are not page aligned */
+ if (NOTALIGNED(to) || NOTALIGNED(ops->len)) {
+#else
+ /* Reject writes, which are not page aligned */
+ if (NOTALIGNED(to)) {
+#endif
+ pr_notice("%s: attempt to write non page aligned data\n",
+ __func__);
return -EINVAL;
+ }
+
+ column = to & (mtd->writesize - 1);
chipnr = (int)(to >> chip->chip_shift);
chip->select_chip(mtd, chipnr);
/* Check, if it is write protected */
if (nand_check_wp(mtd)) {
- printk (KERN_NOTICE "nand_do_write_ops: Device is write protected\n");
- return -EIO;
+ ret = -EIO;
+ goto err_out;
}
realpage = (int)(to >> chip->page_shift);
(chip->pagebuf << chip->page_shift) < (to + ops->len))
chip->pagebuf = -1;
- /* If we're not given explicit OOB data, let it be 0xFF */
- if (likely(!oob))
- memset(chip->oob_poi, 0xff, mtd->oobsize);
-
/* Don't allow multipage oob writes with offset */
- if (oob && ops->ooboffs && (ops->ooboffs + ops->ooblen > oobmaxlen))
- return -EINVAL;
+ if (oob && ops->ooboffs && (ops->ooboffs + ops->ooblen > oobmaxlen)) {
+ ret = -EINVAL;
+ goto err_out;
+ }
while (1) {
- WATCHDOG_RESET();
-
int bytes = mtd->writesize;
int cached = writelen > bytes && page != blockmask;
uint8_t *wbuf = buf;
- /* Partial page write ? */
- if (unlikely(column || writelen < mtd->writesize)) {
+ WATCHDOG_RESET();
+ /* Partial page write? */
+ if (unlikely(column || writelen < (mtd->writesize - 1))) {
cached = 0;
bytes = min_t(int, bytes - column, (int) writelen);
chip->pagebuf = -1;
if (unlikely(oob)) {
size_t len = min(oobwritelen, oobmaxlen);
- oob = nand_fill_oob(chip, oob, len, ops);
+ oob = nand_fill_oob(mtd, oob, len, ops);
oobwritelen -= len;
+ } else {
+ /* We still need to erase leftover OOB data */
+ memset(chip->oob_poi, 0xff, mtd->oobsize);
}
-
- ret = chip->write_page(mtd, chip, wbuf, page, cached,
- (ops->mode == MTD_OOB_RAW));
+ ret = chip->write_page(mtd, chip, column, bytes, wbuf,
+ oob_required, page, cached,
+ (ops->mode == MTD_OPS_RAW));
if (ret)
break;
ops->retlen = ops->len - writelen;
if (unlikely(oob))
ops->oobretlen = ops->ooblen;
+
+err_out:
+ chip->select_chip(mtd, -1);
return ret;
}
/**
- * nand_write - [MTD Interface] NAND write with ECC
- * @mtd: MTD device structure
- * @to: offset to write to
- * @len: number of bytes to write
- * @retlen: pointer to variable to store the number of written bytes
- * @buf: the data to write
+ * panic_nand_write - [MTD Interface] NAND write with ECC
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @len: number of bytes to write
+ * @retlen: pointer to variable to store the number of written bytes
+ * @buf: the data to write
*
- * NAND write with ECC
+ * NAND write with ECC. Used when performing writes in interrupt context, this
+ * may for example be called by mtdoops when writing an oops while in panic.
*/
-static int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const uint8_t *buf)
+static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const uint8_t *buf)
{
struct nand_chip *chip = mtd->priv;
+ struct mtd_oob_ops ops;
int ret;
- /* Do not allow writes past end of device */
- if ((to + len) > mtd->size)
- return -EINVAL;
- if (!len)
- return 0;
+ /* Wait for the device to get ready */
+ panic_nand_wait(mtd, chip, 400);
- nand_get_device(chip, mtd, FL_WRITING);
+ /* Grab the device */
+ panic_nand_get_device(chip, mtd, FL_WRITING);
- chip->ops.len = len;
- chip->ops.datbuf = (uint8_t *)buf;
- chip->ops.oobbuf = NULL;
+ ops.len = len;
+ ops.datbuf = (uint8_t *)buf;
+ ops.oobbuf = NULL;
+ ops.mode = MTD_OPS_PLACE_OOB;
- ret = nand_do_write_ops(mtd, to, &chip->ops);
+ ret = nand_do_write_ops(mtd, to, &ops);
- *retlen = chip->ops.retlen;
+ *retlen = ops.retlen;
+ return ret;
+}
- nand_release_device(mtd);
+/**
+ * nand_write - [MTD Interface] NAND write with ECC
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @len: number of bytes to write
+ * @retlen: pointer to variable to store the number of written bytes
+ * @buf: the data to write
+ *
+ * NAND write with ECC.
+ */
+static int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const uint8_t *buf)
+{
+ struct mtd_oob_ops ops;
+ int ret;
+ nand_get_device(mtd, FL_WRITING);
+ ops.len = len;
+ ops.datbuf = (uint8_t *)buf;
+ ops.oobbuf = NULL;
+ ops.mode = MTD_OPS_PLACE_OOB;
+ ret = nand_do_write_ops(mtd, to, &ops);
+ *retlen = ops.retlen;
+ nand_release_device(mtd);
return ret;
}
/**
* nand_do_write_oob - [MTD Interface] NAND write out-of-band
- * @mtd: MTD device structure
- * @to: offset to write to
- * @ops: oob operation description structure
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operation description structure
*
- * NAND write out-of-band
+ * NAND write out-of-band.
*/
static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
struct mtd_oob_ops *ops)
int chipnr, page, status, len;
struct nand_chip *chip = mtd->priv;
- MTDDEBUG(MTD_DEBUG_LEVEL3, "%s: to = 0x%08x, len = %i\n",
+ pr_debug("%s: to = 0x%08x, len = %i\n",
__func__, (unsigned int)to, (int)ops->ooblen);
- if (ops->mode == MTD_OOB_AUTO)
+ if (ops->mode == MTD_OPS_AUTO_OOB)
len = chip->ecc.layout->oobavail;
else
len = mtd->oobsize;
/* Do not allow write past end of page */
if ((ops->ooboffs + ops->ooblen) > len) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt to write "
- "past end of page\n", __func__);
+ pr_debug("%s: attempt to write past end of page\n",
+ __func__);
return -EINVAL;
}
if (unlikely(ops->ooboffs >= len)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt to start "
- "write outside oob\n", __func__);
+ pr_debug("%s: attempt to start write outside oob\n",
+ __func__);
return -EINVAL;
}
ops->ooboffs + ops->ooblen >
((mtd->size >> chip->page_shift) -
(to >> chip->page_shift)) * len)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt write beyond "
- "end of device\n", __func__);
+ pr_debug("%s: attempt to write beyond end of device\n",
+ __func__);
return -EINVAL;
}
chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
/* Check, if it is write protected */
- if (nand_check_wp(mtd))
+ if (nand_check_wp(mtd)) {
+ chip->select_chip(mtd, -1);
return -EROFS;
+ }
/* Invalidate the page cache, if we write to the cached page */
if (page == chip->pagebuf)
chip->pagebuf = -1;
- memset(chip->oob_poi, 0xff, mtd->oobsize);
- nand_fill_oob(chip, ops->oobbuf, ops->ooblen, ops);
- status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
- memset(chip->oob_poi, 0xff, mtd->oobsize);
+ nand_fill_oob(mtd, ops->oobbuf, ops->ooblen, ops);
+
+ if (ops->mode == MTD_OPS_RAW)
+ status = chip->ecc.write_oob_raw(mtd, chip, page & chip->pagemask);
+ else
+ status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
+
+ chip->select_chip(mtd, -1);
if (status)
return status;
/**
* nand_write_oob - [MTD Interface] NAND write data and/or out-of-band
- * @mtd: MTD device structure
- * @to: offset to write to
- * @ops: oob operation description structure
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operation description structure
*/
static int nand_write_oob(struct mtd_info *mtd, loff_t to,
struct mtd_oob_ops *ops)
{
- struct nand_chip *chip = mtd->priv;
int ret = -ENOTSUPP;
ops->retlen = 0;
/* Do not allow writes past end of device */
if (ops->datbuf && (to + ops->len) > mtd->size) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt write beyond "
- "end of device\n", __func__);
+ pr_debug("%s: attempt to write beyond end of device\n",
+ __func__);
return -EINVAL;
}
- nand_get_device(chip, mtd, FL_WRITING);
+ nand_get_device(mtd, FL_WRITING);
switch (ops->mode) {
- case MTD_OOB_PLACE:
- case MTD_OOB_AUTO:
- case MTD_OOB_RAW:
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_AUTO_OOB:
+ case MTD_OPS_RAW:
break;
default:
}
/**
- * single_erease_cmd - [GENERIC] NAND standard block erase command function
- * @mtd: MTD device structure
- * @page: the page address of the block which will be erased
+ * single_erase_cmd - [GENERIC] NAND standard block erase command function
+ * @mtd: MTD device structure
+ * @page: the page address of the block which will be erased
*
- * Standard erase command for NAND chips
+ * Standard erase command for NAND chips.
*/
static void single_erase_cmd(struct mtd_info *mtd, int page)
{
chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
}
-/**
- * multi_erease_cmd - [GENERIC] AND specific block erase command function
- * @mtd: MTD device structure
- * @page: the page address of the block which will be erased
- *
- * AND multi block erase command function
- * Erase 4 consecutive blocks
- */
-static void multi_erase_cmd(struct mtd_info *mtd, int page)
-{
- struct nand_chip *chip = mtd->priv;
- /* Send commands to erase a block */
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++);
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++);
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++);
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
- chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
-}
-
/**
* nand_erase - [MTD Interface] erase block(s)
- * @mtd: MTD device structure
- * @instr: erase instruction
+ * @mtd: MTD device structure
+ * @instr: erase instruction
*
- * Erase one ore more blocks
+ * Erase one ore more blocks.
*/
static int nand_erase(struct mtd_info *mtd, struct erase_info *instr)
{
return nand_erase_nand(mtd, instr, 0);
}
-#define BBT_PAGE_MASK 0xffffff3f
/**
- * nand_erase_nand - [Internal] erase block(s)
- * @mtd: MTD device structure
- * @instr: erase instruction
- * @allowbbt: allow erasing the bbt area
+ * nand_erase_nand - [INTERN] erase block(s)
+ * @mtd: MTD device structure
+ * @instr: erase instruction
+ * @allowbbt: allow erasing the bbt area
*
- * Erase one ore more blocks
+ * Erase one ore more blocks.
*/
int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
int allowbbt)
{
int page, status, pages_per_block, ret, chipnr;
struct nand_chip *chip = mtd->priv;
- loff_t rewrite_bbt[CONFIG_SYS_NAND_MAX_CHIPS] = {0};
- unsigned int bbt_masked_page = 0xffffffff;
loff_t len;
- MTDDEBUG(MTD_DEBUG_LEVEL3, "%s: start = 0x%012llx, len = %llu\n",
- __func__, (unsigned long long)instr->addr,
- (unsigned long long)instr->len);
+ pr_debug("%s: start = 0x%012llx, len = %llu\n",
+ __func__, (unsigned long long)instr->addr,
+ (unsigned long long)instr->len);
if (check_offs_len(mtd, instr->addr, instr->len))
return -EINVAL;
- instr->fail_addr = MTD_FAIL_ADDR_UNKNOWN;
-
/* Grab the lock and see if the device is available */
- nand_get_device(chip, mtd, FL_ERASING);
+ nand_get_device(mtd, FL_ERASING);
/* Shift to get first page */
page = (int)(instr->addr >> chip->page_shift);
/* Check, if it is write protected */
if (nand_check_wp(mtd)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Device is write protected!!!\n",
- __func__);
+ pr_debug("%s: device is write protected!\n",
+ __func__);
instr->state = MTD_ERASE_FAILED;
goto erase_exit;
}
- /*
- * If BBT requires refresh, set the BBT page mask to see if the BBT
- * should be rewritten. Otherwise the mask is set to 0xffffffff which
- * can not be matched. This is also done when the bbt is actually
- * erased to avoid recusrsive updates
- */
- if (chip->options & BBT_AUTO_REFRESH && !allowbbt)
- bbt_masked_page = chip->bbt_td->pages[chipnr] & BBT_PAGE_MASK;
-
/* Loop through the pages */
len = instr->len;
while (len) {
WATCHDOG_RESET();
- /*
- * heck if we have a bad block, we do not erase bad blocks !
- */
- if (!instr->scrub && nand_block_checkbad(mtd, ((loff_t) page) <<
+
+ /* Check if we have a bad block, we do not erase bad blocks! */
+ if (nand_block_checkbad(mtd, ((loff_t) page) <<
chip->page_shift, 0, allowbbt)) {
- printk(KERN_WARNING "%s: attempt to erase a bad block "
- "at page 0x%08x\n", __func__, page);
+ pr_warn("%s: attempt to erase a bad block at page 0x%08x\n",
+ __func__, page);
instr->state = MTD_ERASE_FAILED;
goto erase_exit;
}
/*
* Invalidate the page cache, if we erase the block which
- * contains the current cached page
+ * contains the current cached page.
*/
if (page <= chip->pagebuf && chip->pagebuf <
(page + pages_per_block))
/* See if block erase succeeded */
if (status & NAND_STATUS_FAIL) {
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: Failed erase, "
- "page 0x%08x\n", __func__, page);
+ pr_debug("%s: failed erase, page 0x%08x\n",
+ __func__, page);
instr->state = MTD_ERASE_FAILED;
instr->fail_addr =
((loff_t)page << chip->page_shift);
goto erase_exit;
}
- /*
- * If BBT requires refresh, set the BBT rewrite flag to the
- * page being erased
- */
- if (bbt_masked_page != 0xffffffff &&
- (page & BBT_PAGE_MASK) == bbt_masked_page)
- rewrite_bbt[chipnr] =
- ((loff_t)page << chip->page_shift);
-
/* Increment page address and decrement length */
- len -= (1 << chip->phys_erase_shift);
+ len -= (1ULL << chip->phys_erase_shift);
page += pages_per_block;
/* Check, if we cross a chip boundary */
chipnr++;
chip->select_chip(mtd, -1);
chip->select_chip(mtd, chipnr);
-
- /*
- * If BBT requires refresh and BBT-PERCHIP, set the BBT
- * page mask to see if this BBT should be rewritten
- */
- if (bbt_masked_page != 0xffffffff &&
- (chip->bbt_td->options & NAND_BBT_PERCHIP))
- bbt_masked_page = chip->bbt_td->pages[chipnr] &
- BBT_PAGE_MASK;
}
}
instr->state = MTD_ERASE_DONE;
ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO;
/* Deselect and wake up anyone waiting on the device */
+ chip->select_chip(mtd, -1);
nand_release_device(mtd);
/* Do call back function */
if (!ret)
mtd_erase_callback(instr);
- /*
- * If BBT requires refresh and erase was successful, rewrite any
- * selected bad block tables
- */
- if (bbt_masked_page == 0xffffffff || ret)
- return ret;
-
- for (chipnr = 0; chipnr < chip->numchips; chipnr++) {
- if (!rewrite_bbt[chipnr])
- continue;
- /* update the BBT for chip */
- MTDDEBUG(MTD_DEBUG_LEVEL0, "%s: nand_update_bbt "
- "(%d:0x%0llx 0x%0x)\n", __func__, chipnr,
- rewrite_bbt[chipnr], chip->bbt_td->pages[chipnr]);
- nand_update_bbt(mtd, rewrite_bbt[chipnr]);
- }
-
/* Return more or less happy */
return ret;
}
/**
* nand_sync - [MTD Interface] sync
- * @mtd: MTD device structure
+ * @mtd: MTD device structure
*
- * Sync is actually a wait for chip ready function
+ * Sync is actually a wait for chip ready function.
*/
static void nand_sync(struct mtd_info *mtd)
{
- struct nand_chip *chip = mtd->priv;
-
- MTDDEBUG(MTD_DEBUG_LEVEL3, "%s: called\n", __func__);
+ pr_debug("%s: called\n", __func__);
/* Grab the lock and see if the device is available */
- nand_get_device(chip, mtd, FL_SYNCING);
+ nand_get_device(mtd, FL_SYNCING);
/* Release it and go back */
nand_release_device(mtd);
}
/**
* nand_block_isbad - [MTD Interface] Check if block at offset is bad
- * @mtd: MTD device structure
- * @offs: offset relative to mtd start
+ * @mtd: MTD device structure
+ * @offs: offset relative to mtd start
*/
static int nand_block_isbad(struct mtd_info *mtd, loff_t offs)
{
- /* Check for invalid offset */
- if (offs > mtd->size)
- return -EINVAL;
-
return nand_block_checkbad(mtd, offs, 1, 0);
}
/**
* nand_block_markbad - [MTD Interface] Mark block at the given offset as bad
- * @mtd: MTD device structure
- * @ofs: offset relative to mtd start
+ * @mtd: MTD device structure
+ * @ofs: offset relative to mtd start
*/
static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs)
{
- struct nand_chip *chip = mtd->priv;
int ret;
ret = nand_block_isbad(mtd, ofs);
if (ret) {
- /* If it was bad already, return success and do nothing. */
+ /* If it was bad already, return success and do nothing */
if (ret > 0)
return 0;
return ret;
}
- return chip->block_markbad(mtd, ofs);
+ return nand_block_markbad_lowlevel(mtd, ofs);
}
-/*
- * Set default functions
+/**
+ * nand_onfi_set_features- [REPLACEABLE] set features for ONFI nand
+ * @mtd: MTD device structure
+ * @chip: nand chip info structure
+ * @addr: feature address.
+ * @subfeature_param: the subfeature parameters, a four bytes array.
+ */
+static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip,
+ int addr, uint8_t *subfeature_param)
+{
+ int status;
+ int i;
+
+#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
+ if (!chip->onfi_version ||
+ !(le16_to_cpu(chip->onfi_params.opt_cmd)
+ & ONFI_OPT_CMD_SET_GET_FEATURES))
+ return -EINVAL;
+#endif
+
+ chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, addr, -1);
+ for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i)
+ chip->write_byte(mtd, subfeature_param[i]);
+
+ status = chip->waitfunc(mtd, chip);
+ if (status & NAND_STATUS_FAIL)
+ return -EIO;
+ return 0;
+}
+
+/**
+ * nand_onfi_get_features- [REPLACEABLE] get features for ONFI nand
+ * @mtd: MTD device structure
+ * @chip: nand chip info structure
+ * @addr: feature address.
+ * @subfeature_param: the subfeature parameters, a four bytes array.
+ */
+static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip,
+ int addr, uint8_t *subfeature_param)
+{
+ int i;
+
+#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
+ if (!chip->onfi_version ||
+ !(le16_to_cpu(chip->onfi_params.opt_cmd)
+ & ONFI_OPT_CMD_SET_GET_FEATURES))
+ return -EINVAL;
+#endif
+
+ /* clear the sub feature parameters */
+ memset(subfeature_param, 0, ONFI_SUBFEATURE_PARAM_LEN);
+
+ chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, addr, -1);
+ for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i)
+ *subfeature_param++ = chip->read_byte(mtd);
+ return 0;
+}
+
+#ifndef __UBOOT__
+/**
+ * nand_suspend - [MTD Interface] Suspend the NAND flash
+ * @mtd: MTD device structure
*/
+static int nand_suspend(struct mtd_info *mtd)
+{
+ return nand_get_device(mtd, FL_PM_SUSPENDED);
+}
+
+/**
+ * nand_resume - [MTD Interface] Resume the NAND flash
+ * @mtd: MTD device structure
+ */
+static void nand_resume(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ if (chip->state == FL_PM_SUSPENDED)
+ nand_release_device(mtd);
+ else
+ pr_err("%s called for a chip which is not in suspended state\n",
+ __func__);
+}
+#endif
+
+/* Set default functions */
static void nand_set_defaults(struct nand_chip *chip, int busw)
{
/* check for proper chip_delay setup, set 20us if not */
if (!chip->select_chip)
chip->select_chip = nand_select_chip;
- if (!chip->read_byte)
+
+ /* set for ONFI nand */
+ if (!chip->onfi_set_features)
+ chip->onfi_set_features = nand_onfi_set_features;
+ if (!chip->onfi_get_features)
+ chip->onfi_get_features = nand_onfi_get_features;
+
+ /* If called twice, pointers that depend on busw may need to be reset */
+ if (!chip->read_byte || chip->read_byte == nand_read_byte)
chip->read_byte = busw ? nand_read_byte16 : nand_read_byte;
if (!chip->read_word)
chip->read_word = nand_read_word;
chip->block_bad = nand_block_bad;
if (!chip->block_markbad)
chip->block_markbad = nand_default_block_markbad;
- if (!chip->write_buf)
+ if (!chip->write_buf || chip->write_buf == nand_write_buf)
chip->write_buf = busw ? nand_write_buf16 : nand_write_buf;
- if (!chip->read_buf)
+ if (!chip->write_byte || chip->write_byte == nand_write_byte)
+ chip->write_byte = busw ? nand_write_byte16 : nand_write_byte;
+ if (!chip->read_buf || chip->read_buf == nand_read_buf)
chip->read_buf = busw ? nand_read_buf16 : nand_read_buf;
- if (!chip->verify_buf)
- chip->verify_buf = busw ? nand_verify_buf16 : nand_verify_buf;
if (!chip->scan_bbt)
chip->scan_bbt = nand_default_bbt;
- if (!chip->controller)
+#ifdef __UBOOT__
+#if defined(CONFIG_MTD_NAND_VERIFY_WRITE)
+ if (!chip->verify_buf)
+ chip->verify_buf = busw ? nand_verify_buf16 : nand_verify_buf;
+#endif
+#endif
+
+ if (!chip->controller) {
chip->controller = &chip->hwcontrol;
+ spin_lock_init(&chip->controller->lock);
+ init_waitqueue_head(&chip->controller->wq);
+ }
+
}
-#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
-/*
- * sanitize ONFI strings so we can safely print them
- */
+/* Sanitize ONFI strings so we can safely print them */
+#ifndef __UBOOT__
+static void sanitize_string(uint8_t *s, size_t len)
+#else
static void sanitize_string(char *s, size_t len)
+#endif
{
ssize_t i;
- /* null terminate */
+ /* Null terminate */
s[len - 1] = 0;
- /* remove non printable chars */
+ /* Remove non printable chars */
for (i = 0; i < len - 1; i++) {
if (s[i] < ' ' || s[i] > 127)
s[i] = '?';
}
- /* remove trailing spaces */
+ /* Remove trailing spaces */
strim(s);
}
return crc;
}
+#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
+/* Parse the Extended Parameter Page. */
+static int nand_flash_detect_ext_param_page(struct mtd_info *mtd,
+ struct nand_chip *chip, struct nand_onfi_params *p)
+{
+ struct onfi_ext_param_page *ep;
+ struct onfi_ext_section *s;
+ struct onfi_ext_ecc_info *ecc;
+ uint8_t *cursor;
+ int ret = -EINVAL;
+ int len;
+ int i;
+
+ len = le16_to_cpu(p->ext_param_page_length) * 16;
+ ep = kmalloc(len, GFP_KERNEL);
+ if (!ep)
+ return -ENOMEM;
+
+ /* Send our own NAND_CMD_PARAM. */
+ chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1);
+
+ /* Use the Change Read Column command to skip the ONFI param pages. */
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT,
+ sizeof(*p) * p->num_of_param_pages , -1);
+
+ /* Read out the Extended Parameter Page. */
+ chip->read_buf(mtd, (uint8_t *)ep, len);
+ if ((onfi_crc16(ONFI_CRC_BASE, ((uint8_t *)ep) + 2, len - 2)
+ != le16_to_cpu(ep->crc))) {
+ pr_debug("fail in the CRC.\n");
+ goto ext_out;
+ }
+
+ /*
+ * Check the signature.
+ * Do not strictly follow the ONFI spec, maybe changed in future.
+ */
+#ifndef __UBOOT__
+ if (strncmp(ep->sig, "EPPS", 4)) {
+#else
+ if (strncmp((char *)ep->sig, "EPPS", 4)) {
+#endif
+ pr_debug("The signature is invalid.\n");
+ goto ext_out;
+ }
+
+ /* find the ECC section. */
+ cursor = (uint8_t *)(ep + 1);
+ for (i = 0; i < ONFI_EXT_SECTION_MAX; i++) {
+ s = ep->sections + i;
+ if (s->type == ONFI_SECTION_TYPE_2)
+ break;
+ cursor += s->length * 16;
+ }
+ if (i == ONFI_EXT_SECTION_MAX) {
+ pr_debug("We can not find the ECC section.\n");
+ goto ext_out;
+ }
+
+ /* get the info we want. */
+ ecc = (struct onfi_ext_ecc_info *)cursor;
+
+ if (!ecc->codeword_size) {
+ pr_debug("Invalid codeword size\n");
+ goto ext_out;
+ }
+
+ chip->ecc_strength_ds = ecc->ecc_bits;
+ chip->ecc_step_ds = 1 << ecc->codeword_size;
+ ret = 0;
+
+ext_out:
+ kfree(ep);
+ return ret;
+}
+
+static int nand_setup_read_retry_micron(struct mtd_info *mtd, int retry_mode)
+{
+ struct nand_chip *chip = mtd->priv;
+ uint8_t feature[ONFI_SUBFEATURE_PARAM_LEN] = {retry_mode};
+
+ return chip->onfi_set_features(mtd, chip, ONFI_FEATURE_ADDR_READ_RETRY,
+ feature);
+}
+
/*
- * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise
+ * Configure chip properties from Micron vendor-specific ONFI table
+ */
+static void nand_onfi_detect_micron(struct nand_chip *chip,
+ struct nand_onfi_params *p)
+{
+ struct nand_onfi_vendor_micron *micron = (void *)p->vendor;
+
+ if (le16_to_cpu(p->vendor_revision) < 1)
+ return;
+
+ chip->read_retries = micron->read_retry_options;
+ chip->setup_read_retry = nand_setup_read_retry_micron;
+}
+
+/*
+ * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise.
*/
static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
int *busw)
{
struct nand_onfi_params *p = &chip->onfi_params;
- int i;
+ int i, j;
int val;
- /* try ONFI for unknow chip or LP */
+ /* Try ONFI for unknown chip or LP */
chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1);
if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' ||
chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I')
return 0;
- MTDDEBUG(MTD_DEBUG_LEVEL0, "ONFI flash detected\n");
chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1);
for (i = 0; i < 3; i++) {
- chip->read_buf(mtd, (uint8_t *)p, sizeof(*p));
+ for (j = 0; j < sizeof(*p); j++)
+ ((uint8_t *)p)[j] = chip->read_byte(mtd);
if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) ==
le16_to_cpu(p->crc)) {
- MTDDEBUG(MTD_DEBUG_LEVEL0,
- "ONFI param page %d valid\n", i);
break;
}
}
- if (i == 3)
+ if (i == 3) {
+ pr_err("Could not find valid ONFI parameter page; aborting\n");
return 0;
+ }
- /* check version */
+ /* Check version */
val = le16_to_cpu(p->revision);
if (val & (1 << 5))
chip->onfi_version = 23;
chip->onfi_version = 20;
else if (val & (1 << 1))
chip->onfi_version = 10;
- else
- chip->onfi_version = 0;
if (!chip->onfi_version) {
- printk(KERN_INFO "%s: unsupported ONFI version: %d\n",
- __func__, val);
+ pr_info("unsupported ONFI version: %d\n", val);
return 0;
}
sanitize_string(p->model, sizeof(p->model));
if (!mtd->name)
mtd->name = p->model;
+
mtd->writesize = le32_to_cpu(p->byte_per_page);
- mtd->erasesize = le32_to_cpu(p->pages_per_block) * mtd->writesize;
+
+ /*
+ * pages_per_block and blocks_per_lun may not be a power-of-2 size
+ * (don't ask me who thought of this...). MTD assumes that these
+ * dimensions will be power-of-2, so just truncate the remaining area.
+ */
+ mtd->erasesize = 1 << (fls(le32_to_cpu(p->pages_per_block)) - 1);
+ mtd->erasesize *= mtd->writesize;
+
mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page);
- chip->chipsize = le32_to_cpu(p->blocks_per_lun);
+
+ /* See erasesize comment */
+ chip->chipsize = 1 << (fls(le32_to_cpu(p->blocks_per_lun)) - 1);
chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count;
- *busw = 0;
- if (le16_to_cpu(p->features) & 1)
+ chip->bits_per_cell = p->bits_per_cell;
+
+ if (onfi_feature(chip) & ONFI_FEATURE_16_BIT_BUS)
*busw = NAND_BUSWIDTH_16;
+ else
+ *busw = 0;
- chip->options |= NAND_NO_READRDY | NAND_NO_AUTOINCR;
+ if (p->ecc_bits != 0xff) {
+ chip->ecc_strength_ds = p->ecc_bits;
+ chip->ecc_step_ds = 512;
+ } else if (chip->onfi_version >= 21 &&
+ (onfi_feature(chip) & ONFI_FEATURE_EXT_PARAM_PAGE)) {
+
+ /*
+ * The nand_flash_detect_ext_param_page() uses the
+ * Change Read Column command which maybe not supported
+ * by the chip->cmdfunc. So try to update the chip->cmdfunc
+ * now. We do not replace user supplied command function.
+ */
+ if (mtd->writesize > 512 && chip->cmdfunc == nand_command)
+ chip->cmdfunc = nand_command_lp;
+
+ /* The Extended Parameter Page is supported since ONFI 2.1. */
+ if (nand_flash_detect_ext_param_page(mtd, chip, p))
+ pr_warn("Failed to detect ONFI extended param page\n");
+ } else {
+ pr_warn("Could not retrieve ONFI ECC requirements\n");
+ }
+
+ if (p->jedec_id == NAND_MFR_MICRON)
+ nand_onfi_detect_micron(chip, p);
return 1;
}
#else
-static inline int nand_flash_detect_onfi(struct mtd_info *mtd,
- struct nand_chip *chip,
+static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
int *busw)
{
return 0;
#endif
/*
- * Get the flash and manufacturer id and lookup if the type is supported
+ * Check if the NAND chip is JEDEC compliant, returns 1 if it is, 0 otherwise.
*/
-static const struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
+static int nand_flash_detect_jedec(struct mtd_info *mtd, struct nand_chip *chip,
+ int *busw)
+{
+ struct nand_jedec_params *p = &chip->jedec_params;
+ struct jedec_ecc_info *ecc;
+ int val;
+ int i, j;
+
+ /* Try JEDEC for unknown chip or LP */
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x40, -1);
+ if (chip->read_byte(mtd) != 'J' || chip->read_byte(mtd) != 'E' ||
+ chip->read_byte(mtd) != 'D' || chip->read_byte(mtd) != 'E' ||
+ chip->read_byte(mtd) != 'C')
+ return 0;
+
+ chip->cmdfunc(mtd, NAND_CMD_PARAM, 0x40, -1);
+ for (i = 0; i < 3; i++) {
+ for (j = 0; j < sizeof(*p); j++)
+ ((uint8_t *)p)[j] = chip->read_byte(mtd);
+
+ if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 510) ==
+ le16_to_cpu(p->crc))
+ break;
+ }
+
+ if (i == 3) {
+ pr_err("Could not find valid JEDEC parameter page; aborting\n");
+ return 0;
+ }
+
+ /* Check version */
+ val = le16_to_cpu(p->revision);
+ if (val & (1 << 2))
+ chip->jedec_version = 10;
+ else if (val & (1 << 1))
+ chip->jedec_version = 1; /* vendor specific version */
+
+ if (!chip->jedec_version) {
+ pr_info("unsupported JEDEC version: %d\n", val);
+ return 0;
+ }
+
+ sanitize_string(p->manufacturer, sizeof(p->manufacturer));
+ sanitize_string(p->model, sizeof(p->model));
+ if (!mtd->name)
+ mtd->name = p->model;
+
+ mtd->writesize = le32_to_cpu(p->byte_per_page);
+
+ /* Please reference to the comment for nand_flash_detect_onfi. */
+ mtd->erasesize = 1 << (fls(le32_to_cpu(p->pages_per_block)) - 1);
+ mtd->erasesize *= mtd->writesize;
+
+ mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page);
+
+ /* Please reference to the comment for nand_flash_detect_onfi. */
+ chip->chipsize = 1 << (fls(le32_to_cpu(p->blocks_per_lun)) - 1);
+ chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count;
+ chip->bits_per_cell = p->bits_per_cell;
+
+ if (jedec_feature(chip) & JEDEC_FEATURE_16_BIT_BUS)
+ *busw = NAND_BUSWIDTH_16;
+ else
+ *busw = 0;
+
+ /* ECC info */
+ ecc = &p->ecc_info[0];
+
+ if (ecc->codeword_size >= 9) {
+ chip->ecc_strength_ds = ecc->ecc_bits;
+ chip->ecc_step_ds = 1 << ecc->codeword_size;
+ } else {
+ pr_warn("Invalid codeword size\n");
+ }
+
+ return 1;
+}
+
+/*
+ * nand_id_has_period - Check if an ID string has a given wraparound period
+ * @id_data: the ID string
+ * @arrlen: the length of the @id_data array
+ * @period: the period of repitition
+ *
+ * Check if an ID string is repeated within a given sequence of bytes at
+ * specific repetition interval period (e.g., {0x20,0x01,0x7F,0x20} has a
+ * period of 3). This is a helper function for nand_id_len(). Returns non-zero
+ * if the repetition has a period of @period; otherwise, returns zero.
+ */
+static int nand_id_has_period(u8 *id_data, int arrlen, int period)
+{
+ int i, j;
+ for (i = 0; i < period; i++)
+ for (j = i + period; j < arrlen; j += period)
+ if (id_data[i] != id_data[j])
+ return 0;
+ return 1;
+}
+
+/*
+ * nand_id_len - Get the length of an ID string returned by CMD_READID
+ * @id_data: the ID string
+ * @arrlen: the length of the @id_data array
+
+ * Returns the length of the ID string, according to known wraparound/trailing
+ * zero patterns. If no pattern exists, returns the length of the array.
+ */
+static int nand_id_len(u8 *id_data, int arrlen)
+{
+ int last_nonzero, period;
+
+ /* Find last non-zero byte */
+ for (last_nonzero = arrlen - 1; last_nonzero >= 0; last_nonzero--)
+ if (id_data[last_nonzero])
+ break;
+
+ /* All zeros */
+ if (last_nonzero < 0)
+ return 0;
+
+ /* Calculate wraparound period */
+ for (period = 1; period < arrlen; period++)
+ if (nand_id_has_period(id_data, arrlen, period))
+ break;
+
+ /* There's a repeated pattern */
+ if (period < arrlen)
+ return period;
+
+ /* There are trailing zeros */
+ if (last_nonzero < arrlen - 1)
+ return last_nonzero + 1;
+
+ /* No pattern detected */
+ return arrlen;
+}
+
+/* Extract the bits of per cell from the 3rd byte of the extended ID */
+static int nand_get_bits_per_cell(u8 cellinfo)
+{
+ int bits;
+
+ bits = cellinfo & NAND_CI_CELLTYPE_MSK;
+ bits >>= NAND_CI_CELLTYPE_SHIFT;
+ return bits + 1;
+}
+
+/*
+ * Many new NAND share similar device ID codes, which represent the size of the
+ * chip. The rest of the parameters must be decoded according to generic or
+ * manufacturer-specific "extended ID" decoding patterns.
+ */
+static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip,
+ u8 id_data[8], int *busw)
+{
+ int extid, id_len;
+ /* The 3rd id byte holds MLC / multichip data */
+ chip->bits_per_cell = nand_get_bits_per_cell(id_data[2]);
+ /* The 4th id byte is the important one */
+ extid = id_data[3];
+
+ id_len = nand_id_len(id_data, 8);
+
+ /*
+ * Field definitions are in the following datasheets:
+ * Old style (4,5 byte ID): Samsung K9GAG08U0M (p.32)
+ * New Samsung (6 byte ID): Samsung K9GAG08U0F (p.44)
+ * Hynix MLC (6 byte ID): Hynix H27UBG8T2B (p.22)
+ *
+ * Check for ID length, non-zero 6th byte, cell type, and Hynix/Samsung
+ * ID to decide what to do.
+ */
+ if (id_len == 6 && id_data[0] == NAND_MFR_SAMSUNG &&
+ !nand_is_slc(chip) && id_data[5] != 0x00) {
+ /* Calc pagesize */
+ mtd->writesize = 2048 << (extid & 0x03);
+ extid >>= 2;
+ /* Calc oobsize */
+ switch (((extid >> 2) & 0x04) | (extid & 0x03)) {
+ case 1:
+ mtd->oobsize = 128;
+ break;
+ case 2:
+ mtd->oobsize = 218;
+ break;
+ case 3:
+ mtd->oobsize = 400;
+ break;
+ case 4:
+ mtd->oobsize = 436;
+ break;
+ case 5:
+ mtd->oobsize = 512;
+ break;
+ case 6:
+ mtd->oobsize = 640;
+ break;
+ case 7:
+ default: /* Other cases are "reserved" (unknown) */
+ mtd->oobsize = 1024;
+ break;
+ }
+ extid >>= 2;
+ /* Calc blocksize */
+ mtd->erasesize = (128 * 1024) <<
+ (((extid >> 1) & 0x04) | (extid & 0x03));
+ *busw = 0;
+ } else if (id_len == 6 && id_data[0] == NAND_MFR_HYNIX &&
+ !nand_is_slc(chip)) {
+ unsigned int tmp;
+
+ /* Calc pagesize */
+ mtd->writesize = 2048 << (extid & 0x03);
+ extid >>= 2;
+ /* Calc oobsize */
+ switch (((extid >> 2) & 0x04) | (extid & 0x03)) {
+ case 0:
+ mtd->oobsize = 128;
+ break;
+ case 1:
+ mtd->oobsize = 224;
+ break;
+ case 2:
+ mtd->oobsize = 448;
+ break;
+ case 3:
+ mtd->oobsize = 64;
+ break;
+ case 4:
+ mtd->oobsize = 32;
+ break;
+ case 5:
+ mtd->oobsize = 16;
+ break;
+ default:
+ mtd->oobsize = 640;
+ break;
+ }
+ extid >>= 2;
+ /* Calc blocksize */
+ tmp = ((extid >> 1) & 0x04) | (extid & 0x03);
+ if (tmp < 0x03)
+ mtd->erasesize = (128 * 1024) << tmp;
+ else if (tmp == 0x03)
+ mtd->erasesize = 768 * 1024;
+ else
+ mtd->erasesize = (64 * 1024) << tmp;
+ *busw = 0;
+ } else {
+ /* Calc pagesize */
+ mtd->writesize = 1024 << (extid & 0x03);
+ extid >>= 2;
+ /* Calc oobsize */
+ mtd->oobsize = (8 << (extid & 0x01)) *
+ (mtd->writesize >> 9);
+ extid >>= 2;
+ /* Calc blocksize. Blocksize is multiples of 64KiB */
+ mtd->erasesize = (64 * 1024) << (extid & 0x03);
+ extid >>= 2;
+ /* Get buswidth information */
+ *busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0;
+
+ /*
+ * Toshiba 24nm raw SLC (i.e., not BENAND) have 32B OOB per
+ * 512B page. For Toshiba SLC, we decode the 5th/6th byte as
+ * follows:
+ * - ID byte 6, bits[2:0]: 100b -> 43nm, 101b -> 32nm,
+ * 110b -> 24nm
+ * - ID byte 5, bit[7]: 1 -> BENAND, 0 -> raw SLC
+ */
+ if (id_len >= 6 && id_data[0] == NAND_MFR_TOSHIBA &&
+ nand_is_slc(chip) &&
+ (id_data[5] & 0x7) == 0x6 /* 24nm */ &&
+ !(id_data[4] & 0x80) /* !BENAND */) {
+ mtd->oobsize = 32 * mtd->writesize >> 9;
+ }
+
+ }
+}
+
+/*
+ * Old devices have chip data hardcoded in the device ID table. nand_decode_id
+ * decodes a matching ID table entry and assigns the MTD size parameters for
+ * the chip.
+ */
+static void nand_decode_id(struct mtd_info *mtd, struct nand_chip *chip,
+ struct nand_flash_dev *type, u8 id_data[8],
+ int *busw)
+{
+ int maf_id = id_data[0];
+
+ mtd->erasesize = type->erasesize;
+ mtd->writesize = type->pagesize;
+ mtd->oobsize = mtd->writesize / 32;
+ *busw = type->options & NAND_BUSWIDTH_16;
+
+ /* All legacy ID NAND are small-page, SLC */
+ chip->bits_per_cell = 1;
+
+ /*
+ * Check for Spansion/AMD ID + repeating 5th, 6th byte since
+ * some Spansion chips have erasesize that conflicts with size
+ * listed in nand_ids table.
+ * Data sheet (5 byte ID): Spansion S30ML-P ORNAND (p.39)
+ */
+ if (maf_id == NAND_MFR_AMD && id_data[4] != 0x00 && id_data[5] == 0x00
+ && id_data[6] == 0x00 && id_data[7] == 0x00
+ && mtd->writesize == 512) {
+ mtd->erasesize = 128 * 1024;
+ mtd->erasesize <<= ((id_data[3] & 0x03) << 1);
+ }
+}
+
+/*
+ * Set the bad block marker/indicator (BBM/BBI) patterns according to some
+ * heuristic patterns using various detected parameters (e.g., manufacturer,
+ * page size, cell-type information).
+ */
+static void nand_decode_bbm_options(struct mtd_info *mtd,
+ struct nand_chip *chip, u8 id_data[8])
+{
+ int maf_id = id_data[0];
+
+ /* Set the bad block position */
+ if (mtd->writesize > 512 || (chip->options & NAND_BUSWIDTH_16))
+ chip->badblockpos = NAND_LARGE_BADBLOCK_POS;
+ else
+ chip->badblockpos = NAND_SMALL_BADBLOCK_POS;
+
+ /*
+ * Bad block marker is stored in the last page of each block on Samsung
+ * and Hynix MLC devices; stored in first two pages of each block on
+ * Micron devices with 2KiB pages and on SLC Samsung, Hynix, Toshiba,
+ * AMD/Spansion, and Macronix. All others scan only the first page.
+ */
+ if (!nand_is_slc(chip) &&
+ (maf_id == NAND_MFR_SAMSUNG ||
+ maf_id == NAND_MFR_HYNIX))
+ chip->bbt_options |= NAND_BBT_SCANLASTPAGE;
+ else if ((nand_is_slc(chip) &&
+ (maf_id == NAND_MFR_SAMSUNG ||
+ maf_id == NAND_MFR_HYNIX ||
+ maf_id == NAND_MFR_TOSHIBA ||
+ maf_id == NAND_MFR_AMD ||
+ maf_id == NAND_MFR_MACRONIX)) ||
+ (mtd->writesize == 2048 &&
+ maf_id == NAND_MFR_MICRON))
+ chip->bbt_options |= NAND_BBT_SCAN2NDPAGE;
+}
+
+static inline bool is_full_id_nand(struct nand_flash_dev *type)
+{
+ return type->id_len;
+}
+
+static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip,
+ struct nand_flash_dev *type, u8 *id_data, int *busw)
+{
+#ifndef __UBOOT__
+ if (!strncmp(type->id, id_data, type->id_len)) {
+#else
+ if (!strncmp((char *)type->id, (char *)id_data, type->id_len)) {
+#endif
+ mtd->writesize = type->pagesize;
+ mtd->erasesize = type->erasesize;
+ mtd->oobsize = type->oobsize;
+
+ chip->bits_per_cell = nand_get_bits_per_cell(id_data[2]);
+ chip->chipsize = (uint64_t)type->chipsize << 20;
+ chip->options |= type->options;
+ chip->ecc_strength_ds = NAND_ECC_STRENGTH(type);
+ chip->ecc_step_ds = NAND_ECC_STEP(type);
+
+ *busw = type->options & NAND_BUSWIDTH_16;
+
+ if (!mtd->name)
+ mtd->name = type->name;
+
+ return true;
+ }
+ return false;
+}
+
+/*
+ * Get the flash and manufacturer id and lookup if the type is supported.
+ */
+static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
struct nand_chip *chip,
- int busw,
int *maf_id, int *dev_id,
- const struct nand_flash_dev *type)
+ struct nand_flash_dev *type)
{
- const char *name;
+ int busw;
int i, maf_idx;
u8 id_data[8];
- int ret;
/* Select the device */
chip->select_chip(mtd, 0);
/*
* Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx)
- * after power-up
+ * after power-up.
*/
chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
*maf_id = chip->read_byte(mtd);
*dev_id = chip->read_byte(mtd);
- /* Try again to make sure, as some systems the bus-hold or other
+ /*
+ * Try again to make sure, as some systems the bus-hold or other
* interface concerns can cause random data which looks like a
* possibly credible NAND flash to appear. If the two results do
* not match, ignore the device completely.
chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
- for (i = 0; i < 2; i++)
+ /* Read entire ID string */
+ for (i = 0; i < 8; i++)
id_data[i] = chip->read_byte(mtd);
if (id_data[0] != *maf_id || id_data[1] != *dev_id) {
- printk(KERN_INFO "%s: second ID read did not match "
- "%02x,%02x against %02x,%02x\n", __func__,
- *maf_id, *dev_id, id_data[0], id_data[1]);
+ pr_info("second ID read did not match %02x,%02x against %02x,%02x\n",
+ *maf_id, *dev_id, id_data[0], id_data[1]);
return ERR_PTR(-ENODEV);
}
if (!type)
type = nand_flash_ids;
- for (; type->name != NULL; type++)
- if (*dev_id == type->id)
- break;
+ for (; type->name != NULL; type++) {
+ if (is_full_id_nand(type)) {
+ if (find_full_id_nand(mtd, chip, type, id_data, &busw))
+ goto ident_done;
+ } else if (*dev_id == type->dev_id) {
+ break;
+ }
+ }
chip->onfi_version = 0;
if (!type->name || !type->pagesize) {
/* Check is chip is ONFI compliant */
- ret = nand_flash_detect_onfi(mtd, chip, &busw);
- if (ret)
+ if (nand_flash_detect_onfi(mtd, chip, &busw))
goto ident_done;
- }
-
- chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
- /* Read entire ID string */
-
- for (i = 0; i < 8; i++)
- id_data[i] = chip->read_byte(mtd);
+ /* Check if the chip is JEDEC compliant */
+ if (nand_flash_detect_jedec(mtd, chip, &busw))
+ goto ident_done;
+ }
if (!type->name)
return ERR_PTR(-ENODEV);
chip->chipsize = (uint64_t)type->chipsize << 20;
if (!type->pagesize && chip->init_size) {
- /* set the pagesize, oobsize, erasesize by the driver*/
+ /* Set the pagesize, oobsize, erasesize by the driver */
busw = chip->init_size(mtd, chip, id_data);
} else if (!type->pagesize) {
- int extid;
- /* The 3rd id byte holds MLC / multichip data */
- chip->cellinfo = id_data[2];
- /* The 4th id byte is the important one */
- extid = id_data[3];
-
- /*
- * Field definitions are in the following datasheets:
- * Old style (4,5 byte ID): Samsung K9GAG08U0M (p.32)
- * New style (6 byte ID): Samsung K9GBG08U0M (p.40)
- *
- * Check for wraparound + Samsung ID + nonzero 6th byte
- * to decide what to do.
- */
- if (id_data[0] == id_data[6] && id_data[1] == id_data[7] &&
- id_data[0] == NAND_MFR_SAMSUNG &&
- (chip->cellinfo & NAND_CI_CELLTYPE_MSK) &&
- id_data[5] != 0x00) {
- /* Calc pagesize */
- mtd->writesize = 2048 << (extid & 0x03);
- extid >>= 2;
- /* Calc oobsize */
- switch (extid & 0x03) {
- case 1:
- mtd->oobsize = 128;
- break;
- case 2:
- mtd->oobsize = 218;
- break;
- case 3:
- mtd->oobsize = 400;
- break;
- default:
- mtd->oobsize = 436;
- break;
- }
- extid >>= 2;
- /* Calc blocksize */
- mtd->erasesize = (128 * 1024) <<
- (((extid >> 1) & 0x04) | (extid & 0x03));
- busw = 0;
- } else {
- /* Calc pagesize */
- mtd->writesize = 1024 << (extid & 0x03);
- extid >>= 2;
- /* Calc oobsize */
- mtd->oobsize = (8 << (extid & 0x01)) *
- (mtd->writesize >> 9);
- extid >>= 2;
- /* Calc blocksize. Blocksize is multiples of 64KiB */
- mtd->erasesize = (64 * 1024) << (extid & 0x03);
- extid >>= 2;
- /* Get buswidth information */
- busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0;
- }
+ /* Decode parameters from extended ID */
+ nand_decode_ext_id(mtd, chip, id_data, &busw);
} else {
- /*
- * Old devices have chip data hardcoded in the device id table
- */
- mtd->erasesize = type->erasesize;
- mtd->writesize = type->pagesize;
- mtd->oobsize = mtd->writesize / 32;
- busw = type->options & NAND_BUSWIDTH_16;
-
- /*
- * Check for Spansion/AMD ID + repeating 5th, 6th byte since
- * some Spansion chips have erasesize that conflicts with size
- * listed in nand_ids table
- * Data sheet (5 byte ID): Spansion S30ML-P ORNAND (p.39)
- */
- if (*maf_id == NAND_MFR_AMD && id_data[4] != 0x00 &&
- id_data[5] == 0x00 && id_data[6] == 0x00 &&
- id_data[7] == 0x00 && mtd->writesize == 512) {
- mtd->erasesize = 128 * 1024;
- mtd->erasesize <<= ((id_data[3] & 0x03) << 1);
- }
+ nand_decode_id(mtd, chip, type, id_data, &busw);
}
- /* Get chip options, preserve non chip based options */
+ /* Get chip options */
chip->options |= type->options;
- /* Check if chip is a not a samsung device. Do not clear the
- * options for chips which are not having an extended id.
+ /*
+ * Check if chip is not a Samsung device. Do not clear the
+ * options for chips which do not have an extended id.
*/
if (*maf_id != NAND_MFR_SAMSUNG && !type->pagesize)
chip->options &= ~NAND_SAMSUNG_LP_OPTIONS;
ident_done:
- /*
- * Set chip as a default. Board drivers can override it, if necessary
- */
- chip->options |= NAND_NO_AUTOINCR;
-
/* Try to identify manufacturer */
for (maf_idx = 0; nand_manuf_ids[maf_idx].id != 0x0; maf_idx++) {
if (nand_manuf_ids[maf_idx].id == *maf_id)
break;
}
- /*
- * Check, if buswidth is correct. Hardware drivers should set
- * chip correct !
- */
- if (busw != (chip->options & NAND_BUSWIDTH_16)) {
- printk(KERN_INFO "NAND device: Manufacturer ID:"
- " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id,
- *dev_id, nand_manuf_ids[maf_idx].name, mtd->name);
- printk(KERN_WARNING "NAND bus width %d instead %d bit\n",
- (chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
- busw ? 16 : 8);
+ if (chip->options & NAND_BUSWIDTH_AUTO) {
+ WARN_ON(chip->options & NAND_BUSWIDTH_16);
+ chip->options |= busw;
+ nand_set_defaults(chip, busw);
+ } else if (busw != (chip->options & NAND_BUSWIDTH_16)) {
+ /*
+ * Check, if buswidth is correct. Hardware drivers should set
+ * chip correct!
+ */
+ pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
+ *maf_id, *dev_id);
+ pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, mtd->name);
+ pr_warn("bus width %d instead %d bit\n",
+ (chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
+ busw ? 16 : 8);
return ERR_PTR(-EINVAL);
}
+ nand_decode_bbm_options(mtd, chip, id_data);
+
/* Calculate the address shift from the page size */
chip->page_shift = ffs(mtd->writesize) - 1;
- /* Convert chipsize to number of pages per chip -1. */
+ /* Convert chipsize to number of pages per chip -1 */
chip->pagemask = (chip->chipsize >> chip->page_shift) - 1;
chip->bbt_erase_shift = chip->phys_erase_shift =
}
chip->badblockbits = 8;
+ chip->erase_cmd = single_erase_cmd;
- /* Set the bad block position */
- if (mtd->writesize > 512 || (busw & NAND_BUSWIDTH_16))
- chip->badblockpos = NAND_LARGE_BADBLOCK_POS;
- else
- chip->badblockpos = NAND_SMALL_BADBLOCK_POS;
-
- /*
- * Bad block marker is stored in the last page of each block
- * on Samsung and Hynix MLC devices; stored in first two pages
- * of each block on Micron devices with 2KiB pages and on
- * SLC Samsung, Hynix, Toshiba and AMD/Spansion. All others scan
- * only the first page.
- */
- if ((chip->cellinfo & NAND_CI_CELLTYPE_MSK) &&
- (*maf_id == NAND_MFR_SAMSUNG ||
- *maf_id == NAND_MFR_HYNIX))
- chip->options |= NAND_BBT_SCANLASTPAGE;
- else if ((!(chip->cellinfo & NAND_CI_CELLTYPE_MSK) &&
- (*maf_id == NAND_MFR_SAMSUNG ||
- *maf_id == NAND_MFR_HYNIX ||
- *maf_id == NAND_MFR_TOSHIBA ||
- *maf_id == NAND_MFR_AMD)) ||
- (mtd->writesize == 2048 &&
- *maf_id == NAND_MFR_MICRON))
- chip->options |= NAND_BBT_SCAN2NDPAGE;
-
- /*
- * Numonyx/ST 2K pages, x8 bus use BOTH byte 1 and 6
- */
- if (!(busw & NAND_BUSWIDTH_16) &&
- *maf_id == NAND_MFR_STMICRO &&
- mtd->writesize == 2048) {
- chip->options |= NAND_BBT_SCANBYTE1AND6;
- chip->badblockpos = 0;
- }
-
- /* Check for AND chips with 4 page planes */
- if (chip->options & NAND_4PAGE_ARRAY)
- chip->erase_cmd = multi_erase_cmd;
- else
- chip->erase_cmd = single_erase_cmd;
-
- /* Do not replace user supplied command function ! */
+ /* Do not replace user supplied command function! */
if (mtd->writesize > 512 && chip->cmdfunc == nand_command)
chip->cmdfunc = nand_command_lp;
- /* TODO onfi flash name */
- name = type->name;
+ pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
+ *maf_id, *dev_id);
+
#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
if (chip->onfi_version)
- name = chip->onfi_params.model;
+ pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ chip->onfi_params.model);
+ else if (chip->jedec_version)
+ pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ chip->jedec_params.model);
+ else
+ pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ type->name);
+#else
+ if (chip->jedec_version)
+ pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ chip->jedec_params.model);
+ else
+ pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ type->name);
+
+ pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ type->name);
#endif
- MTDDEBUG(MTD_DEBUG_LEVEL0, "NAND device: Manufacturer ID:"
- " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, *dev_id,
- nand_manuf_ids[maf_idx].name, name);
+ pr_info("%dMiB, %s, page size: %d, OOB size: %d\n",
+ (int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC",
+ mtd->writesize, mtd->oobsize);
return type;
}
/**
* nand_scan_ident - [NAND Interface] Scan for the NAND device
- * @mtd: MTD device structure
- * @maxchips: Number of chips to scan for
- * @table: Alternative NAND ID table
+ * @mtd: MTD device structure
+ * @maxchips: number of chips to scan for
+ * @table: alternative NAND ID table
*
- * This is the first phase of the normal nand_scan() function. It
- * reads the flash ID and sets up MTD fields accordingly.
+ * This is the first phase of the normal nand_scan() function. It reads the
+ * flash ID and sets up MTD fields accordingly.
*
* The mtd->owner field must be set to the module of the caller.
*/
int nand_scan_ident(struct mtd_info *mtd, int maxchips,
- const struct nand_flash_dev *table)
+ struct nand_flash_dev *table)
{
- int i, busw, nand_maf_id, nand_dev_id;
+ int i, nand_maf_id, nand_dev_id;
struct nand_chip *chip = mtd->priv;
- const struct nand_flash_dev *type;
+ struct nand_flash_dev *type;
- /* Get buswidth to select the correct functions */
- busw = chip->options & NAND_BUSWIDTH_16;
/* Set the default functions */
- nand_set_defaults(chip, busw);
+ nand_set_defaults(chip, chip->options & NAND_BUSWIDTH_16);
/* Read the flash type */
- type = nand_get_flash_type(mtd, chip, busw,
- &nand_maf_id, &nand_dev_id, table);
+ type = nand_get_flash_type(mtd, chip, &nand_maf_id,
+ &nand_dev_id, table);
if (IS_ERR(type)) {
-#ifndef CONFIG_SYS_NAND_QUIET_TEST
- printk(KERN_WARNING "No NAND device found!!!\n");
-#endif
+ if (!(chip->options & NAND_SCAN_SILENT_NODEV))
+ pr_warn("No NAND device found\n");
chip->select_chip(mtd, -1);
return PTR_ERR(type);
}
+ chip->select_chip(mtd, -1);
+
/* Check for a chip array */
for (i = 1; i < maxchips; i++) {
chip->select_chip(mtd, i);
chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
/* Read manufacturer and device IDs */
if (nand_maf_id != chip->read_byte(mtd) ||
- nand_dev_id != chip->read_byte(mtd))
+ nand_dev_id != chip->read_byte(mtd)) {
+ chip->select_chip(mtd, -1);
break;
+ }
+ chip->select_chip(mtd, -1);
}
+
#ifdef DEBUG
if (i > 1)
- printk(KERN_INFO "%d NAND chips detected\n", i);
+ pr_info("%d chips detected\n", i);
#endif
/* Store the number of chips and calc total size for mtd */
return 0;
}
+EXPORT_SYMBOL(nand_scan_ident);
/**
* nand_scan_tail - [NAND Interface] Scan for the NAND device
- * @mtd: MTD device structure
+ * @mtd: MTD device structure
*
- * This is the second phase of the normal nand_scan() function. It
- * fills out all the uninitialized function pointers with the defaults
- * and scans for a bad block table if appropriate.
+ * This is the second phase of the normal nand_scan() function. It fills out
+ * all the uninitialized function pointers with the defaults and scans for a
+ * bad block table if appropriate.
*/
int nand_scan_tail(struct mtd_info *mtd)
{
int i;
struct nand_chip *chip = mtd->priv;
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
+ struct nand_buffers *nbuf;
+
+ /* New bad blocks should be marked in OOB, flash-based BBT, or both */
+ BUG_ON((chip->bbt_options & NAND_BBT_NO_OOB_BBM) &&
+ !(chip->bbt_options & NAND_BBT_USE_FLASH));
+
+ if (!(chip->options & NAND_OWN_BUFFERS)) {
+#ifndef __UBOOT__
+ nbuf = kzalloc(sizeof(*nbuf) + mtd->writesize
+ + mtd->oobsize * 3, GFP_KERNEL);
+ if (!nbuf)
+ return -ENOMEM;
+ nbuf->ecccalc = (uint8_t *)(nbuf + 1);
+ nbuf->ecccode = nbuf->ecccalc + mtd->oobsize;
+ nbuf->databuf = nbuf->ecccode + mtd->oobsize;
+#else
+ nbuf = kzalloc(sizeof(struct nand_buffers), GFP_KERNEL);
+#endif
- if (!(chip->options & NAND_OWN_BUFFERS))
- chip->buffers = memalign(ARCH_DMA_MINALIGN,
- sizeof(*chip->buffers));
- if (!chip->buffers)
- return -ENOMEM;
+ chip->buffers = nbuf;
+ } else {
+ if (!chip->buffers)
+ return -ENOMEM;
+ }
/* Set the internal oob buffer location, just after the page data */
chip->oob_poi = chip->buffers->databuf + mtd->writesize;
/*
- * If no default placement scheme is given, select an appropriate one
+ * If no default placement scheme is given, select an appropriate one.
*/
- if (!chip->ecc.layout && (chip->ecc.mode != NAND_ECC_SOFT_BCH)) {
+ if (!ecc->layout && (ecc->mode != NAND_ECC_SOFT_BCH)) {
switch (mtd->oobsize) {
case 8:
- chip->ecc.layout = &nand_oob_8;
+ ecc->layout = &nand_oob_8;
break;
case 16:
- chip->ecc.layout = &nand_oob_16;
+ ecc->layout = &nand_oob_16;
break;
case 64:
- chip->ecc.layout = &nand_oob_64;
+ ecc->layout = &nand_oob_64;
break;
case 128:
- chip->ecc.layout = &nand_oob_128;
+ ecc->layout = &nand_oob_128;
break;
default:
- printk(KERN_WARNING "No oob scheme defined for "
- "oobsize %d\n", mtd->oobsize);
+ pr_warn("No oob scheme defined for oobsize %d\n",
+ mtd->oobsize);
+ BUG();
}
}
chip->write_page = nand_write_page;
/*
- * check ECC mode, default to software if 3byte/512byte hardware ECC is
+ * Check ECC mode, default to software if 3byte/512byte hardware ECC is
* selected and we have 256 byte pagesize fallback to software ECC
*/
- switch (chip->ecc.mode) {
+ switch (ecc->mode) {
case NAND_ECC_HW_OOB_FIRST:
/* Similar to NAND_ECC_HW, but a separate read_page handle */
- if (!chip->ecc.calculate || !chip->ecc.correct ||
- !chip->ecc.hwctl) {
- printk(KERN_WARNING "No ECC functions supplied; "
- "Hardware ECC not possible\n");
+ if (!ecc->calculate || !ecc->correct || !ecc->hwctl) {
+ pr_warn("No ECC functions supplied; "
+ "hardware ECC not possible\n");
BUG();
}
- if (!chip->ecc.read_page)
- chip->ecc.read_page = nand_read_page_hwecc_oob_first;
+ if (!ecc->read_page)
+ ecc->read_page = nand_read_page_hwecc_oob_first;
case NAND_ECC_HW:
- /* Use standard hwecc read page function ? */
- if (!chip->ecc.read_page)
- chip->ecc.read_page = nand_read_page_hwecc;
- if (!chip->ecc.write_page)
- chip->ecc.write_page = nand_write_page_hwecc;
- if (!chip->ecc.read_page_raw)
- chip->ecc.read_page_raw = nand_read_page_raw;
- if (!chip->ecc.write_page_raw)
- chip->ecc.write_page_raw = nand_write_page_raw;
- if (!chip->ecc.read_oob)
- chip->ecc.read_oob = nand_read_oob_std;
- if (!chip->ecc.write_oob)
- chip->ecc.write_oob = nand_write_oob_std;
+ /* Use standard hwecc read page function? */
+ if (!ecc->read_page)
+ ecc->read_page = nand_read_page_hwecc;
+ if (!ecc->write_page)
+ ecc->write_page = nand_write_page_hwecc;
+ if (!ecc->read_page_raw)
+ ecc->read_page_raw = nand_read_page_raw;
+ if (!ecc->write_page_raw)
+ ecc->write_page_raw = nand_write_page_raw;
+ if (!ecc->read_oob)
+ ecc->read_oob = nand_read_oob_std;
+ if (!ecc->write_oob)
+ ecc->write_oob = nand_write_oob_std;
+ if (!ecc->read_subpage)
+ ecc->read_subpage = nand_read_subpage;
+ if (!ecc->write_subpage)
+ ecc->write_subpage = nand_write_subpage_hwecc;
case NAND_ECC_HW_SYNDROME:
- if ((!chip->ecc.calculate || !chip->ecc.correct ||
- !chip->ecc.hwctl) &&
- (!chip->ecc.read_page ||
- chip->ecc.read_page == nand_read_page_hwecc ||
- !chip->ecc.write_page ||
- chip->ecc.write_page == nand_write_page_hwecc)) {
- printk(KERN_WARNING "No ECC functions supplied; "
- "Hardware ECC not possible\n");
+ if ((!ecc->calculate || !ecc->correct || !ecc->hwctl) &&
+ (!ecc->read_page ||
+ ecc->read_page == nand_read_page_hwecc ||
+ !ecc->write_page ||
+ ecc->write_page == nand_write_page_hwecc)) {
+ pr_warn("No ECC functions supplied; "
+ "hardware ECC not possible\n");
BUG();
}
- /* Use standard syndrome read/write page function ? */
- if (!chip->ecc.read_page)
- chip->ecc.read_page = nand_read_page_syndrome;
- if (!chip->ecc.write_page)
- chip->ecc.write_page = nand_write_page_syndrome;
- if (!chip->ecc.read_page_raw)
- chip->ecc.read_page_raw = nand_read_page_raw_syndrome;
- if (!chip->ecc.write_page_raw)
- chip->ecc.write_page_raw = nand_write_page_raw_syndrome;
- if (!chip->ecc.read_oob)
- chip->ecc.read_oob = nand_read_oob_syndrome;
- if (!chip->ecc.write_oob)
- chip->ecc.write_oob = nand_write_oob_syndrome;
-
- if (mtd->writesize >= chip->ecc.size)
+ /* Use standard syndrome read/write page function? */
+ if (!ecc->read_page)
+ ecc->read_page = nand_read_page_syndrome;
+ if (!ecc->write_page)
+ ecc->write_page = nand_write_page_syndrome;
+ if (!ecc->read_page_raw)
+ ecc->read_page_raw = nand_read_page_raw_syndrome;
+ if (!ecc->write_page_raw)
+ ecc->write_page_raw = nand_write_page_raw_syndrome;
+ if (!ecc->read_oob)
+ ecc->read_oob = nand_read_oob_syndrome;
+ if (!ecc->write_oob)
+ ecc->write_oob = nand_write_oob_syndrome;
+
+ if (mtd->writesize >= ecc->size) {
+ if (!ecc->strength) {
+ pr_warn("Driver must set ecc.strength when using hardware ECC\n");
+ BUG();
+ }
break;
- printk(KERN_WARNING "%d byte HW ECC not possible on "
- "%d byte page size, fallback to SW ECC\n",
- chip->ecc.size, mtd->writesize);
- chip->ecc.mode = NAND_ECC_SOFT;
+ }
+ pr_warn("%d byte HW ECC not possible on "
+ "%d byte page size, fallback to SW ECC\n",
+ ecc->size, mtd->writesize);
+ ecc->mode = NAND_ECC_SOFT;
case NAND_ECC_SOFT:
- chip->ecc.calculate = nand_calculate_ecc;
- chip->ecc.correct = nand_correct_data;
- chip->ecc.read_page = nand_read_page_swecc;
- chip->ecc.read_subpage = nand_read_subpage;
- chip->ecc.write_page = nand_write_page_swecc;
- chip->ecc.read_page_raw = nand_read_page_raw;
- chip->ecc.write_page_raw = nand_write_page_raw;
- chip->ecc.read_oob = nand_read_oob_std;
- chip->ecc.write_oob = nand_write_oob_std;
- if (!chip->ecc.size)
- chip->ecc.size = 256;
- chip->ecc.bytes = 3;
+ ecc->calculate = nand_calculate_ecc;
+ ecc->correct = nand_correct_data;
+ ecc->read_page = nand_read_page_swecc;
+ ecc->read_subpage = nand_read_subpage;
+ ecc->write_page = nand_write_page_swecc;
+ ecc->read_page_raw = nand_read_page_raw;
+ ecc->write_page_raw = nand_write_page_raw;
+ ecc->read_oob = nand_read_oob_std;
+ ecc->write_oob = nand_write_oob_std;
+ if (!ecc->size)
+ ecc->size = 256;
+ ecc->bytes = 3;
+ ecc->strength = 1;
break;
case NAND_ECC_SOFT_BCH:
if (!mtd_nand_has_bch()) {
- printk(KERN_WARNING "CONFIG_MTD_ECC_BCH not enabled\n");
- return -EINVAL;
+ pr_warn("CONFIG_MTD_NAND_ECC_BCH not enabled\n");
+ BUG();
}
- chip->ecc.calculate = nand_bch_calculate_ecc;
- chip->ecc.correct = nand_bch_correct_data;
- chip->ecc.read_page = nand_read_page_swecc;
- chip->ecc.read_subpage = nand_read_subpage;
- chip->ecc.write_page = nand_write_page_swecc;
- chip->ecc.read_page_raw = nand_read_page_raw;
- chip->ecc.write_page_raw = nand_write_page_raw;
- chip->ecc.read_oob = nand_read_oob_std;
- chip->ecc.write_oob = nand_write_oob_std;
+ ecc->calculate = nand_bch_calculate_ecc;
+ ecc->correct = nand_bch_correct_data;
+ ecc->read_page = nand_read_page_swecc;
+ ecc->read_subpage = nand_read_subpage;
+ ecc->write_page = nand_write_page_swecc;
+ ecc->read_page_raw = nand_read_page_raw;
+ ecc->write_page_raw = nand_write_page_raw;
+ ecc->read_oob = nand_read_oob_std;
+ ecc->write_oob = nand_write_oob_std;
/*
* Board driver should supply ecc.size and ecc.bytes values to
* select how many bits are correctable; see nand_bch_init()
- * for details.
- * Otherwise, default to 4 bits for large page devices
+ * for details. Otherwise, default to 4 bits for large page
+ * devices.
*/
- if (!chip->ecc.size && (mtd->oobsize >= 64)) {
- chip->ecc.size = 512;
- chip->ecc.bytes = 7;
+ if (!ecc->size && (mtd->oobsize >= 64)) {
+ ecc->size = 512;
+ ecc->bytes = 7;
}
- chip->ecc.priv = nand_bch_init(mtd,
- chip->ecc.size,
- chip->ecc.bytes,
- &chip->ecc.layout);
- if (!chip->ecc.priv)
- printk(KERN_WARNING "BCH ECC initialization failed!\n");
-
+ ecc->priv = nand_bch_init(mtd, ecc->size, ecc->bytes,
+ &ecc->layout);
+ if (!ecc->priv) {
+ pr_warn("BCH ECC initialization failed!\n");
+ BUG();
+ }
+ ecc->strength = ecc->bytes * 8 / fls(8 * ecc->size);
break;
case NAND_ECC_NONE:
- printk(KERN_WARNING "NAND_ECC_NONE selected by board driver. "
- "This is not recommended !!\n");
- chip->ecc.read_page = nand_read_page_raw;
- chip->ecc.write_page = nand_write_page_raw;
- chip->ecc.read_oob = nand_read_oob_std;
- chip->ecc.read_page_raw = nand_read_page_raw;
- chip->ecc.write_page_raw = nand_write_page_raw;
- chip->ecc.write_oob = nand_write_oob_std;
- chip->ecc.size = mtd->writesize;
- chip->ecc.bytes = 0;
+ pr_warn("NAND_ECC_NONE selected by board driver. "
+ "This is not recommended!\n");
+ ecc->read_page = nand_read_page_raw;
+ ecc->write_page = nand_write_page_raw;
+ ecc->read_oob = nand_read_oob_std;
+ ecc->read_page_raw = nand_read_page_raw;
+ ecc->write_page_raw = nand_write_page_raw;
+ ecc->write_oob = nand_write_oob_std;
+ ecc->size = mtd->writesize;
+ ecc->bytes = 0;
+ ecc->strength = 0;
break;
default:
- printk(KERN_WARNING "Invalid NAND_ECC_MODE %d\n",
- chip->ecc.mode);
+ pr_warn("Invalid NAND_ECC_MODE %d\n", ecc->mode);
BUG();
}
+ /* For many systems, the standard OOB write also works for raw */
+ if (!ecc->read_oob_raw)
+ ecc->read_oob_raw = ecc->read_oob;
+ if (!ecc->write_oob_raw)
+ ecc->write_oob_raw = ecc->write_oob;
+
/*
* The number of bytes available for a client to place data into
- * the out of band area
+ * the out of band area.
*/
- chip->ecc.layout->oobavail = 0;
- for (i = 0; chip->ecc.layout->oobfree[i].length
- && i < ARRAY_SIZE(chip->ecc.layout->oobfree); i++)
- chip->ecc.layout->oobavail +=
- chip->ecc.layout->oobfree[i].length;
- mtd->oobavail = chip->ecc.layout->oobavail;
+ ecc->layout->oobavail = 0;
+ for (i = 0; ecc->layout->oobfree[i].length
+ && i < ARRAY_SIZE(ecc->layout->oobfree); i++)
+ ecc->layout->oobavail += ecc->layout->oobfree[i].length;
+ mtd->oobavail = ecc->layout->oobavail;
/*
* Set the number of read / write steps for one page depending on ECC
- * mode
+ * mode.
*/
- chip->ecc.steps = mtd->writesize / chip->ecc.size;
- if (chip->ecc.steps * chip->ecc.size != mtd->writesize) {
- printk(KERN_WARNING "Invalid ecc parameters\n");
+ ecc->steps = mtd->writesize / ecc->size;
+ if (ecc->steps * ecc->size != mtd->writesize) {
+ pr_warn("Invalid ECC parameters\n");
BUG();
}
- chip->ecc.total = chip->ecc.steps * chip->ecc.bytes;
+ ecc->total = ecc->steps * ecc->bytes;
- /*
- * Allow subpage writes up to ecc.steps. Not possible for MLC
- * FLASH.
- */
- if (!(chip->options & NAND_NO_SUBPAGE_WRITE) &&
- !(chip->cellinfo & NAND_CI_CELLTYPE_MSK)) {
- switch (chip->ecc.steps) {
+ /* Allow subpage writes up to ecc.steps. Not possible for MLC flash */
+ if (!(chip->options & NAND_NO_SUBPAGE_WRITE) && nand_is_slc(chip)) {
+ switch (ecc->steps) {
case 2:
mtd->subpage_sft = 1;
break;
/* Initialize state */
chip->state = FL_READY;
- /* De-select the device */
- chip->select_chip(mtd, -1);
-
/* Invalidate the pagebuffer reference */
chip->pagebuf = -1;
/* Large page NAND with SOFT_ECC should support subpage reads */
- if ((chip->ecc.mode == NAND_ECC_SOFT) && (chip->page_shift > 9))
+ if ((ecc->mode == NAND_ECC_SOFT) && (chip->page_shift > 9))
chip->options |= NAND_SUBPAGE_READ;
/* Fill in remaining MTD driver data */
- mtd->type = MTD_NANDFLASH;
+ mtd->type = nand_is_slc(chip) ? MTD_NANDFLASH : MTD_MLCNANDFLASH;
mtd->flags = (chip->options & NAND_ROM) ? MTD_CAP_ROM :
MTD_CAP_NANDFLASH;
- mtd->erase = nand_erase;
- mtd->point = NULL;
- mtd->unpoint = NULL;
- mtd->read = nand_read;
- mtd->write = nand_write;
- mtd->read_oob = nand_read_oob;
- mtd->write_oob = nand_write_oob;
- mtd->sync = nand_sync;
- mtd->lock = NULL;
- mtd->unlock = NULL;
- mtd->block_isbad = nand_block_isbad;
- mtd->block_markbad = nand_block_markbad;
-
- /* propagate ecc.layout to mtd_info */
- mtd->ecclayout = chip->ecc.layout;
+ mtd->_erase = nand_erase;
+#ifndef __UBOOT__
+ mtd->_point = NULL;
+ mtd->_unpoint = NULL;
+#endif
+ mtd->_read = nand_read;
+ mtd->_write = nand_write;
+ mtd->_panic_write = panic_nand_write;
+ mtd->_read_oob = nand_read_oob;
+ mtd->_write_oob = nand_write_oob;
+ mtd->_sync = nand_sync;
+ mtd->_lock = NULL;
+ mtd->_unlock = NULL;
+#ifndef __UBOOT__
+ mtd->_suspend = nand_suspend;
+ mtd->_resume = nand_resume;
+#endif
+ mtd->_block_isbad = nand_block_isbad;
+ mtd->_block_markbad = nand_block_markbad;
+ mtd->writebufsize = mtd->writesize;
+
+ /* propagate ecc info to mtd_info */
+ mtd->ecclayout = ecc->layout;
+ mtd->ecc_strength = ecc->strength;
+ mtd->ecc_step_size = ecc->size;
+ /*
+ * Initialize bitflip_threshold to its default prior scan_bbt() call.
+ * scan_bbt() might invoke mtd_read(), thus bitflip_threshold must be
+ * properly set.
+ */
+ if (!mtd->bitflip_threshold)
+ mtd->bitflip_threshold = mtd->ecc_strength;
/* Check, if we should skip the bad block table scan */
if (chip->options & NAND_SKIP_BBTSCAN)
return 0;
}
+EXPORT_SYMBOL(nand_scan_tail);
+
+/*
+ * is_module_text_address() isn't exported, and it's mostly a pointless
+ * test if this is a module _anyway_ -- they'd have to try _really_ hard
+ * to call us from in-kernel code if the core NAND support is modular.
+ */
+#ifdef MODULE
+#define caller_is_module() (1)
+#else
+#define caller_is_module() \
+ is_module_text_address((unsigned long)__builtin_return_address(0))
+#endif
/**
* nand_scan - [NAND Interface] Scan for the NAND device
- * @mtd: MTD device structure
- * @maxchips: Number of chips to scan for
- *
- * This fills out all the uninitialized function pointers
- * with the defaults.
- * The flash ID is read and the mtd/chip structures are
- * filled with the appropriate values.
- * The mtd->owner field must be set to the module of the caller
+ * @mtd: MTD device structure
+ * @maxchips: number of chips to scan for
*
+ * This fills out all the uninitialized function pointers with the defaults.
+ * The flash ID is read and the mtd/chip structures are filled with the
+ * appropriate values. The mtd->owner field must be set to the module of the
+ * caller.
*/
int nand_scan(struct mtd_info *mtd, int maxchips)
{
int ret;
+ /* Many callers got this wrong, so check for it for a while... */
+ if (!mtd->owner && caller_is_module()) {
+ pr_crit("%s called with NULL mtd->owner!\n", __func__);
+ BUG();
+ }
+
ret = nand_scan_ident(mtd, maxchips, NULL);
if (!ret)
ret = nand_scan_tail(mtd);
return ret;
}
+EXPORT_SYMBOL(nand_scan);
+#ifndef __UBOOT__
/**
* nand_release - [NAND Interface] Free resources held by the NAND device
- * @mtd: MTD device structure
-*/
+ * @mtd: MTD device structure
+ */
void nand_release(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
if (chip->ecc.mode == NAND_ECC_SOFT_BCH)
nand_bch_free((struct nand_bch_control *)chip->ecc.priv);
-#ifdef CONFIG_MTD_PARTITIONS
- /* Deregister partitions */
- del_mtd_partitions(mtd);
-#endif
+ mtd_device_unregister(mtd);
/* Free bad block table memory */
kfree(chip->bbt);
& NAND_BBT_DYNAMICSTRUCT)
kfree(chip->badblock_pattern);
}
+EXPORT_SYMBOL_GPL(nand_release);
+
+static int __init nand_base_init(void)
+{
+ led_trigger_register_simple("nand-disk", &nand_led_trigger);
+ return 0;
+}
+
+static void __exit nand_base_exit(void)
+{
+ led_trigger_unregister_simple(nand_led_trigger);
+}
+#endif
+
+module_init(nand_base_init);
+module_exit(nand_base_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Steven J. Hill <sjhill@realitydiluted.com>");
+MODULE_AUTHOR("Thomas Gleixner <tglx@linutronix.de>");
+MODULE_DESCRIPTION("Generic NAND flash driver code");