uint scr; /* eSDHC control register */
};
+struct fsl_esdhc_plat {
+ struct mmc_config cfg;
+ struct mmc mmc;
+};
+
/**
* struct fsl_esdhc_priv
*
struct fsl_esdhc *esdhc_regs;
unsigned int sdhc_clk;
unsigned int bus_width;
- struct mmc_config cfg;
+#if !CONFIG_IS_ENABLED(BLK)
struct mmc *mmc;
+#endif
struct udevice *dev;
int non_removable;
int wp_enable;
/*
* PIO Read/Write Mode reduce the performace as DMA is not used in this mode.
*/
-static void
-esdhc_pio_read_write(struct mmc *mmc, struct mmc_data *data)
+static void esdhc_pio_read_write(struct fsl_esdhc_priv *priv,
+ struct mmc_data *data)
{
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
uint blocks;
char *buffer;
uint databuf;
uint size;
uint irqstat;
- uint timeout;
+ ulong start;
if (data->flags & MMC_DATA_READ) {
blocks = data->blocks;
buffer = data->dest;
while (blocks) {
- timeout = PIO_TIMEOUT;
+ start = get_timer(0);
size = data->blocksize;
irqstat = esdhc_read32(®s->irqstat);
- while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BREN)
- && --timeout);
- if (timeout <= 0) {
- printf("\nData Read Failed in PIO Mode.");
- return;
+ while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BREN)) {
+ if (get_timer(start) > PIO_TIMEOUT) {
+ printf("\nData Read Failed in PIO Mode.");
+ return;
+ }
}
while (size && (!(irqstat & IRQSTAT_TC))) {
udelay(100); /* Wait before last byte transfer complete */
blocks = data->blocks;
buffer = (char *)data->src;
while (blocks) {
- timeout = PIO_TIMEOUT;
+ start = get_timer(0);
size = data->blocksize;
irqstat = esdhc_read32(®s->irqstat);
- while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BWEN)
- && --timeout);
- if (timeout <= 0) {
- printf("\nData Write Failed in PIO Mode.");
- return;
+ while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BWEN)) {
+ if (get_timer(start) > PIO_TIMEOUT) {
+ printf("\nData Write Failed in PIO Mode.");
+ return;
+ }
}
while (size && (!(irqstat & IRQSTAT_TC))) {
udelay(100); /* Wait before last byte transfer complete */
}
#endif
-static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data)
+static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc,
+ struct mmc_data *data)
{
int timeout;
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234)
dma_addr_t addr;
* Sends a command out on the bus. Takes the mmc pointer,
* a command pointer, and an optional data pointer.
*/
-static int
-esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
+static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
+ struct mmc_cmd *cmd, struct mmc_data *data)
{
int err = 0;
uint xfertyp;
uint irqstat;
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111
/* Set up for a data transfer if we have one */
if (data) {
- err = esdhc_setup_data(mmc, data);
+ err = esdhc_setup_data(priv, mmc, data);
if(err)
return err;
/* Wait until all of the blocks are transferred */
if (data) {
#ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
- esdhc_pio_read_write(mmc, data);
+ esdhc_pio_read_write(priv, data);
#else
do {
irqstat = esdhc_read32(®s->irqstat);
return err;
}
-static void set_sysctl(struct mmc *mmc, uint clock)
+static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock)
{
int div = 1;
#ifdef ARCH_MXC
int pre_div = 2;
#endif
int ddr_pre_div = mmc->ddr_mode ? 2 : 1;
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
int sdhc_clk = priv->sdhc_clk;
uint clk;
}
#ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
-static void esdhc_clock_control(struct mmc *mmc, bool enable)
+static void esdhc_clock_control(struct fsl_esdhc_priv *priv, bool enable)
{
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
u32 value;
u32 time_out;
}
#endif
-static int esdhc_set_ios(struct mmc *mmc)
+static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
{
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
#ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
/* Select to use peripheral clock */
- esdhc_clock_control(mmc, false);
+ esdhc_clock_control(priv, false);
esdhc_setbits32(®s->scr, ESDHCCTL_PCS);
- esdhc_clock_control(mmc, true);
+ esdhc_clock_control(priv, true);
#endif
/* Set the clock speed */
- set_sysctl(mmc, mmc->clock);
+ set_sysctl(priv, mmc, mmc->clock);
/* Set the bus width */
esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8);
return 0;
}
-static int esdhc_init(struct mmc *mmc)
+static int esdhc_init_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
{
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
- int timeout = 1000;
+ ulong start;
/* Reset the entire host controller */
esdhc_setbits32(®s->sysctl, SYSCTL_RSTA);
/* Wait until the controller is available */
- while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA) && --timeout)
- udelay(1000);
+ start = get_timer(0);
+ while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA)) {
+ if (get_timer(start) > 1000)
+ return -ETIMEDOUT;
+ }
#if defined(CONFIG_FSL_USDHC)
/* RSTA doesn't reset MMC_BOOT register, so manually reset it */
esdhc_write32(®s->clktunectrlstatus, 0x0);
/* Put VEND_SPEC to default value */
- esdhc_write32(®s->vendorspec, VENDORSPEC_INIT);
+ if (priv->vs18_enable)
+ esdhc_write32(®s->vendorspec, (VENDORSPEC_INIT |
+ ESDHC_VENDORSPEC_VSELECT));
+ else
+ esdhc_write32(®s->vendorspec, VENDORSPEC_INIT);
/* Disable DLL_CTRL delay line */
esdhc_write32(®s->dllctrl, 0x0);
#endif
/* Set the initial clock speed */
- mmc_set_clock(mmc, 400000);
+ mmc_set_clock(mmc, 400000, false);
/* Disable the BRR and BWR bits in IRQSTAT */
esdhc_clrbits32(®s->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR);
/* Set timout to the maximum value */
esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);
- if (priv->vs18_enable)
- esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
-
return 0;
}
-static int esdhc_getcd(struct mmc *mmc)
+static int esdhc_getcd_common(struct fsl_esdhc_priv *priv)
{
- struct fsl_esdhc_priv *priv = mmc->priv;
struct fsl_esdhc *regs = priv->esdhc_regs;
int timeout = 1000;
return 1;
#endif
-#ifdef CONFIG_DM_MMC
+#if CONFIG_IS_ENABLED(DM_MMC)
if (priv->non_removable)
return 1;
#ifdef CONFIG_DM_GPIO
return timeout > 0;
}
-static void esdhc_reset(struct fsl_esdhc *regs)
+static int esdhc_reset(struct fsl_esdhc *regs)
{
- unsigned long timeout = 100; /* wait max 100 ms */
+ ulong start;
/* reset the controller */
esdhc_setbits32(®s->sysctl, SYSCTL_RSTA);
/* hardware clears the bit when it is done */
- while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA) && --timeout)
- udelay(1000);
- if (!timeout)
- printf("MMC/SD: Reset never completed.\n");
+ start = get_timer(0);
+ while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA)) {
+ if (get_timer(start) > 100) {
+ printf("MMC/SD: Reset never completed.\n");
+ return -ETIMEDOUT;
+ }
+ }
+
+ return 0;
+}
+
+#if !CONFIG_IS_ENABLED(DM_MMC)
+static int esdhc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_priv *priv = mmc->priv;
+
+ return esdhc_getcd_common(priv);
+}
+
+static int esdhc_init(struct mmc *mmc)
+{
+ struct fsl_esdhc_priv *priv = mmc->priv;
+
+ return esdhc_init_common(priv, mmc);
+}
+
+static int esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
+ struct mmc_data *data)
+{
+ struct fsl_esdhc_priv *priv = mmc->priv;
+
+ return esdhc_send_cmd_common(priv, mmc, cmd, data);
+}
+
+static int esdhc_set_ios(struct mmc *mmc)
+{
+ struct fsl_esdhc_priv *priv = mmc->priv;
+
+ return esdhc_set_ios_common(priv, mmc);
}
static const struct mmc_ops esdhc_ops = {
+ .getcd = esdhc_getcd,
+ .init = esdhc_init,
.send_cmd = esdhc_send_cmd,
.set_ios = esdhc_set_ios,
- .init = esdhc_init,
- .getcd = esdhc_getcd,
};
+#endif
-static int fsl_esdhc_init(struct fsl_esdhc_priv *priv)
+static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
+ struct fsl_esdhc_plat *plat)
{
+ struct mmc_config *cfg;
struct fsl_esdhc *regs;
- struct mmc *mmc;
u32 caps, voltage_caps;
+ int ret;
if (!priv)
return -EINVAL;
regs = priv->esdhc_regs;
/* First reset the eSDHC controller */
- esdhc_reset(regs);
+ ret = esdhc_reset(regs);
+ if (ret)
+ return ret;
#ifndef CONFIG_FSL_USDHC
esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
writel(SDHCI_IRQ_EN_BITS, ®s->irqstaten);
- memset(&priv->cfg, 0, sizeof(priv->cfg));
+ cfg = &plat->cfg;
+#ifndef CONFIG_DM_MMC
+ memset(cfg, '\0', sizeof(*cfg));
+#endif
voltage_caps = 0;
caps = esdhc_read32(®s->hostcapblt);
if (caps & ESDHC_HOSTCAPBLT_VS33)
voltage_caps |= MMC_VDD_32_33 | MMC_VDD_33_34;
- priv->cfg.name = "FSL_SDHC";
- priv->cfg.ops = &esdhc_ops;
+ cfg->name = "FSL_SDHC";
+#if !CONFIG_IS_ENABLED(DM_MMC)
+ cfg->ops = &esdhc_ops;
+#endif
#ifdef CONFIG_SYS_SD_VOLTAGE
- priv->cfg.voltages = CONFIG_SYS_SD_VOLTAGE;
+ cfg->voltages = CONFIG_SYS_SD_VOLTAGE;
#else
- priv->cfg.voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
+ cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
#endif
- if ((priv->cfg.voltages & voltage_caps) == 0) {
+ if ((cfg->voltages & voltage_caps) == 0) {
printf("voltage not supported by controller\n");
return -1;
}
if (priv->bus_width == 8)
- priv->cfg.host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
+ cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
else if (priv->bus_width == 4)
- priv->cfg.host_caps = MMC_MODE_4BIT;
+ cfg->host_caps = MMC_MODE_4BIT;
- priv->cfg.host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
+ cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
#ifdef CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
- priv->cfg.host_caps |= MMC_MODE_DDR_52MHz;
+ cfg->host_caps |= MMC_MODE_DDR_52MHz;
#endif
if (priv->bus_width > 0) {
if (priv->bus_width < 8)
- priv->cfg.host_caps &= ~MMC_MODE_8BIT;
+ cfg->host_caps &= ~MMC_MODE_8BIT;
if (priv->bus_width < 4)
- priv->cfg.host_caps &= ~MMC_MODE_4BIT;
+ cfg->host_caps &= ~MMC_MODE_4BIT;
}
if (caps & ESDHC_HOSTCAPBLT_HSS)
- priv->cfg.host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
+ cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
#ifdef CONFIG_ESDHC_DETECT_8_BIT_QUIRK
if (CONFIG_ESDHC_DETECT_8_BIT_QUIRK)
- priv->cfg.host_caps &= ~MMC_MODE_8BIT;
+ cfg->host_caps &= ~MMC_MODE_8BIT;
#endif
- priv->cfg.f_min = 400000;
- priv->cfg.f_max = min(priv->sdhc_clk, (u32)52000000);
+ cfg->f_min = 400000;
+ cfg->f_max = min(priv->sdhc_clk, (u32)52000000);
- priv->cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
-
- mmc = mmc_create(&priv->cfg, priv);
- if (mmc == NULL)
- return -1;
-
- priv->mmc = mmc;
+ cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
return 0;
}
-#ifndef CONFIG_DM_MMC
+#if !CONFIG_IS_ENABLED(DM_MMC)
static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg,
struct fsl_esdhc_priv *priv)
{
int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg)
{
+ struct fsl_esdhc_plat *plat;
struct fsl_esdhc_priv *priv;
+ struct mmc *mmc;
int ret;
if (!cfg)
priv = calloc(sizeof(struct fsl_esdhc_priv), 1);
if (!priv)
return -ENOMEM;
+ plat = calloc(sizeof(struct fsl_esdhc_plat), 1);
+ if (!plat) {
+ free(priv);
+ return -ENOMEM;
+ }
ret = fsl_esdhc_cfg_to_priv(cfg, priv);
if (ret) {
debug("%s xlate failure\n", __func__);
+ free(plat);
free(priv);
return ret;
}
- ret = fsl_esdhc_init(priv);
+ ret = fsl_esdhc_init(priv, plat);
if (ret) {
debug("%s init failure\n", __func__);
+ free(plat);
free(priv);
return ret;
}
+ mmc = mmc_create(&plat->cfg, priv);
+ if (!mmc)
+ return -EIO;
+
+ priv->mmc = mmc;
+
return 0;
}
}
#endif
-#ifdef CONFIG_DM_MMC
+#if CONFIG_IS_ENABLED(DM_MMC)
#include <asm/arch/clock.h>
__weak void init_clk_usdhc(u32 index)
{
static int fsl_esdhc_probe(struct udevice *dev)
{
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
+ struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
- const void *fdt = gd->fdt_blob;
- int node = dev_of_offset(dev);
#ifdef CONFIG_DM_REGULATOR
struct udevice *vqmmc_dev;
#endif
fdt_addr_t addr;
unsigned int val;
+ struct mmc *mmc;
int ret;
- addr = devfdt_get_addr(dev);
+ addr = dev_read_addr(dev);
if (addr == FDT_ADDR_T_NONE)
return -EINVAL;
priv->esdhc_regs = (struct fsl_esdhc *)addr;
priv->dev = dev;
- val = fdtdec_get_int(fdt, node, "bus-width", -1);
+ val = dev_read_u32_default(dev, "bus-width", -1);
if (val == 8)
priv->bus_width = 8;
else if (val == 4)
else
priv->bus_width = 1;
- if (fdt_get_property(fdt, node, "non-removable", NULL)) {
+ if (dev_read_bool(dev, "non-removable")) {
priv->non_removable = 1;
} else {
priv->non_removable = 0;
#ifdef CONFIG_DM_GPIO
- gpio_request_by_name_nodev(offset_to_ofnode(node), "cd-gpios",
- 0, &priv->cd_gpio, GPIOD_IS_IN);
+ gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
+ GPIOD_IS_IN);
#endif
}
priv->wp_enable = 1;
#ifdef CONFIG_DM_GPIO
- ret = gpio_request_by_name_nodev(offset_to_ofnode(node), "wp-gpios", 0,
- &priv->wp_gpio, GPIOD_IS_IN);
+ ret = gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio,
+ GPIOD_IS_IN);
if (ret)
priv->wp_enable = 0;
#endif
return -EINVAL;
}
- ret = fsl_esdhc_init(priv);
+ ret = fsl_esdhc_init(priv, plat);
if (ret) {
dev_err(dev, "fsl_esdhc_init failure\n");
return ret;
}
- upriv->mmc = priv->mmc;
- priv->mmc->dev = dev;
+ mmc = &plat->mmc;
+ mmc->cfg = &plat->cfg;
+ mmc->dev = dev;
+ upriv->mmc = mmc;
- return 0;
+ return esdhc_init_common(priv, mmc);
}
+#if CONFIG_IS_ENABLED(DM_MMC)
+static int fsl_esdhc_get_cd(struct udevice *dev)
+{
+ struct fsl_esdhc_priv *priv = dev_get_priv(dev);
+
+ return true;
+ return esdhc_getcd_common(priv);
+}
+
+static int fsl_esdhc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
+ struct mmc_data *data)
+{
+ struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
+ struct fsl_esdhc_priv *priv = dev_get_priv(dev);
+
+ return esdhc_send_cmd_common(priv, &plat->mmc, cmd, data);
+}
+
+static int fsl_esdhc_set_ios(struct udevice *dev)
+{
+ struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
+ struct fsl_esdhc_priv *priv = dev_get_priv(dev);
+
+ return esdhc_set_ios_common(priv, &plat->mmc);
+}
+
+static const struct dm_mmc_ops fsl_esdhc_ops = {
+ .get_cd = fsl_esdhc_get_cd,
+ .send_cmd = fsl_esdhc_send_cmd,
+ .set_ios = fsl_esdhc_set_ios,
+};
+#endif
+
static const struct udevice_id fsl_esdhc_ids[] = {
{ .compatible = "fsl,imx6ul-usdhc", },
{ .compatible = "fsl,imx6sx-usdhc", },
{ /* sentinel */ }
};
+#if CONFIG_IS_ENABLED(BLK)
+static int fsl_esdhc_bind(struct udevice *dev)
+{
+ struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
+
+ return mmc_bind(dev, &plat->mmc, &plat->cfg);
+}
+#endif
+
U_BOOT_DRIVER(fsl_esdhc) = {
.name = "fsl-esdhc-mmc",
.id = UCLASS_MMC,
.of_match = fsl_esdhc_ids,
+ .ops = &fsl_esdhc_ops,
+#if CONFIG_IS_ENABLED(BLK)
+ .bind = fsl_esdhc_bind,
+#endif
.probe = fsl_esdhc_probe,
+ .platdata_auto_alloc_size = sizeof(struct fsl_esdhc_plat),
.priv_auto_alloc_size = sizeof(struct fsl_esdhc_priv),
};
#endif
projects / oweals / u-boot.git / blobdiff