config MMC
bool "MMC/SD/SDIO card support"
default ARM || PPC || SANDBOX
+ select HAVE_BLOCK_DEVICE
help
This selects MultiMediaCard, Secure Digital and Secure
Digital I/O support.
This adds a command and an API to do hardware partitioning on eMMC
devices.
+config SUPPORT_EMMC_RPMB
+ bool "Support eMMC replay protected memory block (RPMB)"
+ imply CMD_MMC_RPMB
+ help
+ Enable support for reading, writing and programming the
+ key for the Replay Protection Memory Block partition in eMMC.
+
+config SUPPORT_EMMC_BOOT
+ bool "Support some additional features of the eMMC boot partitions"
+ help
+ Enable support for eMMC boot partitions. This also enables
+ extensions within the mmc command.
+
config MMC_IO_VOLTAGE
bool "Support IO voltage configuration"
help
cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
frequency can go up to 208MHz (SDR104)
+config MMC_HS400_SUPPORT
+ bool "enable HS400 support"
+ select MMC_HS200_SUPPORT
+ help
+ The HS400 mode is support by some eMMC. The bus frequency is up to
+ 200MHz. This mode requires tuning the IO.
+
+config SPL_MMC_HS400_SUPPORT
+ bool "enable HS400 support in SPL"
+ help
+ The HS400 mode is support by some eMMC. The bus frequency is up to
+ 200MHz. This mode requires tuning the IO.
+
config MMC_HS200_SUPPORT
bool "enable HS200 support"
help
Enable the output of more information about the card such as the
operating mode.
+config MMC_TRACE
+ bool "MMC debugging"
+ default n
+ help
+ This is an option for use by developer. Enable MMC core debugging.
+
+ If you need to see the MMC core message, say Y.
+
config SPL_MMC_TINY
bool "Tiny MMC framework in SPL"
help
config MMC_DW
bool "Synopsys DesignWare Memory Card Interface"
+ select BOUNCE_BUFFER
help
This selects support for the Synopsys DesignWare Mobile Storage IP
block, this provides host support for SD and MMC interfaces, in both
Synopsys DesignWare Memory Card Interface driver. Select this option
for platforms based on Altera SOCFPGA.
+config MMC_DW_SNPS
+ bool "Extensions for DW Memory Card Interface used in Synopsys ARC devboards"
+ depends on MMC_DW
+ depends on DM_MMC
+ depends on OF_CONTROL
+ depends on CLK
+ help
+ This selects support for Synopsys DesignWare Memory Card Interface driver
+ extensions used in various Synopsys ARC devboards.
+
config MMC_MESON_GX
bool "Meson GX EMMC controller support"
depends on DM_MMC && BLK && ARCH_MESON
config MMC_MXS
bool "Freescale MXS Multimedia Card Interface support"
+ depends on MX23 || MX28 || MX6 || MX7
+ select BOUNCE_BUFFER
+ select APBH_DMA
+ select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7
+ select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7
help
This selects the Freescale SSP MMC controller found on MXS based
platforms like mx23/28.
If unsure, say N.
+config MMC_OMAP_HS_ADMA
+ bool "ADMA support for OMAP HS MMC"
+ depends on MMC_OMAP_HS && !OMAP34XX
+ default y if !AM33XX
+ help
+ This enables support for the ADMA2 controller (SDA3.00 Part A2 DMA
+ controller). If supported by the hardware, selecting this option will
+ increase performances.
+
config MMC_OMAP36XX_PINS
bool "Enable MMC1 on OMAP36xx/37xx"
depends on OMAP34XX && MMC_OMAP_HS
help
Support for the on-chip SDHI host controller on SuperH/Renesas ARM SoCs platform
+config SH_MMCIF
+ bool "SuperH/Renesas ARM SoCs on-chip MMCIF host controller support"
+ depends on ARCH_RMOBILE || SH
+ help
+ Support for the on-chip MMCIF host controller on SuperH/Renesas ARM SoCs platform
+
config MMC_UNIPHIER
- bool "UniPhier/RCar SD/MMC Host Controller support"
- depends on ARCH_UNIPHIER || ARCH_RMOBILE
+ bool "UniPhier SD/MMC Host Controller support"
+ depends on ARCH_UNIPHIER
+ depends on BLK && DM_MMC
+ depends on OF_CONTROL
+ help
+ This selects support for the Matsushita SD/MMC Host Controller on
+ SocioNext UniPhier SoCs.
+
+config RENESAS_SDHI
+ bool "Renesas R-Car SD/MMC Host Controller support"
+ depends on ARCH_RMOBILE
depends on BLK && DM_MMC
depends on OF_CONTROL
help
This selects support for the Matsushita SD/MMC Host Controller on
- SocioNext UniPhier and Renesas RCar SoCs.
+ Renesas R-Car SoCs.
+
+config MMC_BCM2835
+ bool "BCM2835 family custom SD/MMC Host Controller support"
+ depends on ARCH_BCM283X
+ depends on BLK && DM_MMC
+ depends on OF_CONTROL
+ default y
+ help
+ This selects support for the custom SD host controller in the BCM2835
+ family of devices.
+
+ If you have a BCM2835 platform with SD or MMC devices, say Y here.
+
+ If unsure, say N.
+
+config JZ47XX_MMC
+ bool "Ingenic JZ47xx SD/MMC Host Controller support"
+ depends on ARCH_JZ47XX
+ help
+ This selects support for the SD Card Controller on Ingenic JZ47xx SoCs.
config MMC_SANDBOX
bool "Sandbox MMC support"
This enables support for the SDMA (Single Operation DMA) defined
in the SD Host Controller Standard Specification Version 1.00 .
+config MMC_SDHCI_ADMA
+ bool "Support SDHCI ADMA2"
+ depends on MMC_SDHCI
+ help
+ This enables support for the ADMA (Advanced DMA) defined
+ in the SD Host Controller Standard Specification Version 3.00
+
+config SPL_MMC_SDHCI_ADMA
+ bool "Support SDHCI ADMA2 in SPL"
+ depends on MMC_SDHCI
+ help
+ This enables support for the ADMA (Advanced DMA) defined
+ in the SD Host Controller Standard Specification Version 3.00 in SPL.
+
config MMC_SDHCI_ATMEL
bool "Atmel SDHCI controller support"
depends on ARCH_AT91
If unsure, say N.
+config MMC_SDHCI_BCMSTB
+ tristate "SDHCI support for the BCMSTB SD/MMC Controller"
+ depends on MMC_SDHCI
+ help
+ This selects the Broadcom set-top box SD/MMC controller.
+
+ If you have a BCMSTB platform with SD or MMC devices,
+ say Y here.
+
+ If unsure, say N.
+
config MMC_SDHCI_CADENCE
bool "SDHCI support for the Cadence SD/SDIO/eMMC controller"
depends on BLK && DM_MMC
If unsure, say N.
+config MMC_SDHCI_K3_ARASAN
+ bool "Arasan SDHCI controller for TI's K3 based SoCs"
+ depends on ARCH_K3
+ depends on MMC_SDHCI
+ depends on DM_MMC && OF_CONTROL && BLK
+ help
+ Support for Arasan SDHCI host controller on Texas Instruments'
+ K3 family based SoC platforms
+
config MMC_SDHCI_KONA
bool "SDHCI support on Broadcom KONA platform"
depends on MMC_SDHCI
config MMC_SDHCI_TEGRA
bool "SDHCI platform support for the Tegra SD/MMC Controller"
depends on TEGRA
+ select BOUNCE_BUFFER
default y
help
This selects the Tegra SD/MMC controller. If you have a Tegra
config MMC_SDHCI_ZYNQ
bool "Arasan SDHCI controller support"
- depends on ARCH_ZYNQ || ARCH_ZYNQMP
+ depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL
depends on DM_MMC && OF_CONTROL && BLK
depends on MMC_SDHCI
help
Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform
+config ZYNQ_SDHCI_MAX_FREQ
+ int "Set the maximum frequency of the controller"
+ depends on MMC_SDHCI_ZYNQ
+ help
+ Set the maximum frequency of the controller.
+
+config ZYNQ_SDHCI_MIN_FREQ
+ int "Set the minimum frequency of the controller"
+ depends on MMC_SDHCI_ZYNQ
+ default 0
+ help
+ Set the minimum frequency of the controller.
+
config MMC_SUNXI
bool "Allwinner sunxi SD/MMC Host Controller support"
depends on ARCH_SUNXI && !UART0_PORT_F
bool
depends on MMC_SUNXI
+config MMC_SUNXI_HAS_MODE_SWITCH
+ bool
+ depends on MMC_SUNXI
+
config GENERIC_ATMEL_MCI
bool "Atmel Multimedia Card Interface support"
depends on DM_MMC && BLK && ARCH_AT91
If you have a board based on such a SoC and with a SD/MMC slot,
say Y or M here.
-config MMC_NDS32
- bool "Andestech SD/MMC controller support"
- depends on DM_MMC && OF_CONTROL && BLK && FTSDC010
- help
- This enables support for the Andestech SD/MMM controller, which is
- based on Faraday IP.
-
config FTSDC010
bool "Ftsdc010 SD/MMC controller Support"
help
This SD/MMC controller is present in Andestech SoCs which is based on Faraday IP.
+config FTSDC010_SDIO
+ bool "Support ftsdc010 sdio"
+ default n
+ depends on FTSDC010
+ help
+ This can enable ftsdc010 sdio function.
+
+config MMC_MTK
+ bool "MediaTek SD/MMC Card Interface support"
+ depends on ARCH_MEDIATEK
+ depends on BLK && DM_MMC
+ depends on OF_CONTROL
+ help
+ This selects the MediaTek(R) Secure digital and Multimedia card Interface.
+ If you have a machine with a integrated SD/MMC card reader, say Y or M here.
+ This is needed if support for any SD/SDIO/MMC devices is required.
+ If unsure, say N.
+
endif
config TEGRA124_MMC_DISABLE_EXT_LOOPBACK
TODO(marcel.ziswiler@toradex.com): Move to device tree controlled
approach once proper kernel integration made it mainline.
+config FSL_ESDHC
+ bool "Freescale/NXP eSDHC controller support"
+ help
+ This selects support for the eSDHC (enhanced secure digital host
+ controller) found on numerous Freescale/NXP SoCs.
+
endmenu
config SYS_FSL_ERRATUM_ESDHC111
projects / oweals / u-boot.git / blobdiff