/*
- * Copyright 2006 Freescale Semiconductor, Inc.
+ * Copyright 2006,2009 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
#include <asm/io.h>
#include <asm/fsl_i2c.h> /* HW definitions */
-#define I2C_TIMEOUT (CONFIG_SYS_HZ / 4)
+/* The maximum number of microseconds we will wait until another master has
+ * released the bus. If not defined in the board header file, then use a
+ * generic value.
+ */
+#ifndef CONFIG_I2C_MBB_TIMEOUT
+#define CONFIG_I2C_MBB_TIMEOUT 100000
+#endif
+
+/* The maximum number of microseconds we will wait for a read or write
+ * operation to complete. If not defined in the board header file, then use a
+ * generic value.
+ */
+#ifndef CONFIG_I2C_TIMEOUT
+#define CONFIG_I2C_TIMEOUT 10000
+#endif
#define I2C_READ_BIT 1
#define I2C_WRITE_BIT 0
#define CONFIG_SYS_SPD_BUS_NUM 0
#endif
static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = CONFIG_SYS_SPD_BUS_NUM;
+#if defined(CONFIG_I2C_MUX)
+static unsigned int i2c_bus_num_mux __attribute__ ((section ("data"))) = 0;
+#endif
static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SPEED};
*/
static const struct {
unsigned short divider;
-#ifdef __PPC__
- u8 dfsr;
-#endif
u8 fdr;
} fsl_i2c_speed_map[] = {
-#ifdef __PPC__
- {160, 1, 32}, {192, 1, 33}, {224, 1, 34}, {256, 1, 35},
- {288, 1, 0}, {320, 1, 1}, {352, 6, 1}, {384, 1, 2}, {416, 6, 2},
- {448, 1, 38}, {480, 1, 3}, {512, 1, 39}, {544, 11, 3}, {576, 1, 4},
- {608, 22, 3}, {640, 1, 5}, {672, 32, 3}, {704, 11, 5}, {736, 43, 3},
- {768, 1, 6}, {800, 54, 3}, {832, 11, 6}, {896, 1, 42}, {960, 1, 7},
- {1024, 1, 43}, {1088, 22, 7}, {1152, 1, 8}, {1216, 43, 7}, {1280, 1, 9},
- {1408, 22, 9}, {1536, 1, 10}, {1664, 22, 10}, {1792, 1, 46},
- {1920, 1, 11}, {2048, 1, 47}, {2176, 43, 11}, {2304, 1, 12},
- {2560, 1, 13}, {2816, 43, 13}, {3072, 1, 14}, {3328, 43, 14},
- {3584, 1, 50}, {3840, 1, 15}, {4096, 1, 51}, {4608, 1, 16},
- {5120, 1, 17}, {6144, 1, 18}, {7168, 1, 54}, {7680, 1, 19},
- {8192, 1, 55}, {9216, 1, 20}, {10240, 1, 21}, {12288, 1, 22},
- {14336, 1, 58}, {15360, 1, 23}, {16384, 1, 59}, {18432, 1, 24},
- {20480, 1, 25}, {24576, 1, 26}, {28672, 1, 62}, {30720, 1, 27},
- {32768, 1, 63}, {36864, 1, 28}, {40960, 1, 29}, {49152, 1, 30},
- {61440, 1, 31}, {-1, 1, 31}
-#elif defined(__M68K__)
+#ifdef __M68K__
{20, 32}, {22, 33}, {24, 34}, {26, 35},
{28, 0}, {28, 36}, {30, 1}, {32, 37},
{34, 2}, {36, 38}, {40, 3}, {40, 39},
unsigned int i2c_clk, unsigned int speed)
{
unsigned short divider = min(i2c_clk / speed, (unsigned short) -1);
- unsigned int i;
/*
* We want to choose an FDR/DFSR that generates an I2C bus speed that
* want the first divider that is equal to or greater than the
* calculated divider.
*/
+#ifdef __PPC__
+ u8 dfsr, fdr = 0x31; /* Default if no FDR found */
+ /* a, b and dfsr matches identifiers A,B and C respectively in AN2919 */
+ unsigned short a, b, ga, gb;
+ unsigned long c_div, est_div;
+
+#ifdef CONFIG_FSL_I2C_CUSTOM_DFSR
+ dfsr = CONFIG_FSL_I2C_CUSTOM_DFSR;
+#else
+ /* Condition 1: dfsr <= 50/T */
+ dfsr = (5 * (i2c_clk / 1000)) / 100000;
+#endif
+#ifdef CONFIG_FSL_I2C_CUSTOM_FDR
+ fdr = CONFIG_FSL_I2C_CUSTOM_FDR;
+ speed = i2c_clk / divider; /* Fake something */
+#else
+ debug("Requested speed:%d, i2c_clk:%d\n", speed, i2c_clk);
+ if (!dfsr)
+ dfsr = 1;
+
+ est_div = ~0;
+ for (ga = 0x4, a = 10; a <= 30; ga++, a += 2) {
+ for (gb = 0; gb < 8; gb++) {
+ b = 16 << gb;
+ c_div = b * (a + ((3*dfsr)/b)*2);
+ if ((c_div > divider) && (c_div < est_div)) {
+ unsigned short bin_gb, bin_ga;
+
+ est_div = c_div;
+ bin_gb = gb << 2;
+ bin_ga = (ga & 0x3) | ((ga & 0x4) << 3);
+ fdr = bin_gb | bin_ga;
+ speed = i2c_clk / est_div;
+ debug("FDR:0x%.2x, div:%ld, ga:0x%x, gb:0x%x, "
+ "a:%d, b:%d, speed:%d\n",
+ fdr, est_div, ga, gb, a, b, speed);
+ /* Condition 2 not accounted for */
+ debug("Tr <= %d ns\n",
+ (b - 3 * dfsr) * 1000000 /
+ (i2c_clk / 1000));
+ }
+ }
+ if (a == 20)
+ a += 2;
+ if (a == 24)
+ a += 4;
+ }
+ debug("divider:%d, est_div:%ld, DFSR:%d\n", divider, est_div, dfsr);
+ debug("FDR:0x%.2x, speed:%d\n", fdr, speed);
+#endif
+ writeb(dfsr, &dev->dfsrr); /* set default filter */
+ writeb(fdr, &dev->fdr); /* set bus speed */
+#else
+ unsigned int i;
for (i = 0; i < ARRAY_SIZE(fsl_i2c_speed_map); i++)
if (fsl_i2c_speed_map[i].divider >= divider) {
u8 fdr;
-#ifdef __PPC__
- u8 dfsr;
- dfsr = fsl_i2c_speed_map[i].dfsr;
-#endif
+
fdr = fsl_i2c_speed_map[i].fdr;
speed = i2c_clk / fsl_i2c_speed_map[i].divider;
writeb(fdr, &dev->fdr); /* set bus speed */
-#ifdef __PPC__
- writeb(dfsr, &dev->dfsrr); /* set default filter */
-#endif
+
break;
}
-
+#endif
return speed;
}
+unsigned int get_i2c_clock(int bus)
+{
+ if (bus)
+ return gd->i2c2_clk; /* I2C2 clock */
+ else
+ return gd->i2c1_clk; /* I2C1 clock */
+}
+
void
i2c_init(int speed, int slaveadd)
{
- struct fsl_i2c *dev;
+ const struct fsl_i2c *dev;
unsigned int temp;
+ int bus_num, i;
+
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+ /* Call board specific i2c bus reset routine before accessing the
+ * environment, which might be in a chip on that bus. For details
+ * about this problem see doc/I2C_Edge_Conditions.
+ */
+ i2c_init_board();
+#endif
+#ifdef CONFIG_SYS_I2C2_OFFSET
+ bus_num = 2;
+#else
+ bus_num = 1;
+#endif
+ for (i = 0; i < bus_num; i++) {
+ dev = i2c_dev[i];
+
+ writeb(0, &dev->cr); /* stop I2C controller */
+ udelay(5); /* let it shutdown in peace */
+ temp = set_i2c_bus_speed(dev, get_i2c_clock(i), speed);
+ if (gd->flags & GD_FLG_RELOC)
+ i2c_bus_speed[i] = temp;
+ writeb(slaveadd << 1, &dev->adr);/* write slave address */
+ writeb(0x0, &dev->sr); /* clear status register */
+ writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
+ }
- dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
-
- writeb(0, &dev->cr); /* stop I2C controller */
- udelay(5); /* let it shutdown in peace */
- temp = set_i2c_bus_speed(dev, gd->i2c1_clk, speed);
- if (gd->flags & GD_FLG_RELOC)
- i2c_bus_speed[0] = temp;
- writeb(slaveadd << 1, &dev->adr); /* write slave address */
- writeb(0x0, &dev->sr); /* clear status register */
- writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
-
-#ifdef CONFIG_SYS_I2C2_OFFSET
- dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET);
-
- writeb(0, &dev->cr); /* stop I2C controller */
- udelay(5); /* let it shutdown in peace */
- temp = set_i2c_bus_speed(dev, gd->i2c2_clk, speed);
- if (gd->flags & GD_FLG_RELOC)
- i2c_bus_speed[1] = temp;
- writeb(slaveadd << 1, &dev->adr); /* write slave address */
- writeb(0x0, &dev->sr); /* clear status register */
- writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
+#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
+ /* Call board specific i2c bus reset routine AFTER the bus has been
+ * initialized. Use either this callpoint or i2c_init_board;
+ * which is called before i2c_init operations.
+ * For details about this problem see doc/I2C_Edge_Conditions.
+ */
+ i2c_board_late_init();
#endif
}
-static __inline__ int
+static int
i2c_wait4bus(void)
{
unsigned long long timeval = get_ticks();
+ const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT);
while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) {
- if ((get_ticks() - timeval) > usec2ticks(I2C_TIMEOUT))
+ if ((get_ticks() - timeval) > timeout)
return -1;
}
{
u32 csr;
unsigned long long timeval = get_ticks();
+ const unsigned long long timeout = usec2ticks(CONFIG_I2C_TIMEOUT);
do {
csr = readb(&i2c_dev[i2c_bus_num]->sr);
if (!(csr & I2C_SR_MIF))
continue;
+ /* Read again to allow register to stabilise */
+ csr = readb(&i2c_dev[i2c_bus_num]->sr);
writeb(0x0, &i2c_dev[i2c_bus_num]->sr);
}
return 0;
- } while ((get_ticks() - timeval) < usec2ticks(I2C_TIMEOUT));
+ } while ((get_ticks() - timeval) < timeout);
debug("i2c_wait: timed out\n");
return -1;
{
int i;
- writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX,
- &i2c_dev[i2c_bus_num]->cr);
-
for (i = 0; i < length; i++) {
writeb(data[i], &i2c_dev[i2c_bus_num]->dr);
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK,
&i2c_dev[i2c_bus_num]->cr);
- /* Generate stop on last byte */
+ /* Do not generate stop on last byte */
if (i == length - 1)
- writeb(I2C_CR_MEN | I2C_CR_TXAK, &i2c_dev[i2c_bus_num]->cr);
+ writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX,
+ &i2c_dev[i2c_bus_num]->cr);
data[i] = readb(&i2c_dev[i2c_bus_num]->dr);
}
writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr);
+ if (i2c_wait4bus()) /* Wait until STOP */
+ debug("i2c_read: wait4bus timed out\n");
+
if (i == length)
return 0;
}
writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr);
+ if (i2c_wait4bus()) /* Wait until STOP */
+ debug("i2c_write: wait4bus timed out\n");
if (i == length)
return 0;
return i2c_read(chip, 0, 0, NULL, 0);
}
-uchar
-i2c_reg_read(uchar i2c_addr, uchar reg)
-{
- uchar buf[1];
-
- i2c_read(i2c_addr, reg, 1, buf, 1);
-
- return buf[0];
-}
-
-void
-i2c_reg_write(uchar i2c_addr, uchar reg, uchar val)
-{
- i2c_write(i2c_addr, reg, 1, &val, 1);
-}
-
int i2c_set_bus_num(unsigned int bus)
{
+#if defined(CONFIG_I2C_MUX)
+ if (bus < CONFIG_SYS_MAX_I2C_BUS) {
+ i2c_bus_num = bus;
+ } else {
+ int ret;
+
+ ret = i2x_mux_select_mux(bus);
+ if (ret)
+ return ret;
+ i2c_bus_num = 0;
+ }
+ i2c_bus_num_mux = bus;
+#else
#ifdef CONFIG_SYS_I2C2_OFFSET
if (bus > 1) {
#else
}
i2c_bus_num = bus;
-
+#endif
return 0;
}
unsigned int i2c_get_bus_num(void)
{
+#if defined(CONFIG_I2C_MUX)
+ return i2c_bus_num_mux;
+#else
return i2c_bus_num;
+#endif
}
unsigned int i2c_get_bus_speed(void)