+#
+# I2C subsystem configuration
+#
+
+menu "I2C support"
+
config DM_I2C
bool "Enable Driver Model for I2C drivers"
depends on DM
help
- If you want to use driver model for I2C drivers, say Y.
- To use legacy I2C drivers, say N.
+ Enable driver model for I2C. The I2C uclass interface: probe, read,
+ write and speed, is implemented with the bus drivers operations,
+ which provide methods for bus setting and data transfer. Each chip
+ device (bus child) info is kept as parent platdata. The interface
+ is defined in include/i2c.h. When i2c bus driver supports the i2c
+ uclass, but the device drivers not, then DM_I2C_COMPAT config can
+ be used as compatibility layer.
+
+config DM_I2C_COMPAT
+ bool "Enable I2C compatibility layer"
+ depends on DM
+ help
+ Enable old-style I2C functions for compatibility with existing code.
+ This option can be enabled as a temporary measure to avoid needing
+ to convert all code for a board in a single commit. It should not
+ be enabled for any board in an official release.
+
+config I2C_CROS_EC_TUNNEL
+ tristate "Chrome OS EC tunnel I2C bus"
+ depends on CROS_EC
+ help
+ This provides an I2C bus that will tunnel i2c commands through to
+ the other side of the Chrome OS EC to the I2C bus connected there.
+ This will work whatever the interface used to talk to the EC (SPI,
+ I2C or LPC). Some Chromebooks use this when the hardware design
+ does not allow direct access to the main PMIC from the AP.
+
+config I2C_CROS_EC_LDO
+ bool "Provide access to LDOs on the Chrome OS EC"
+ depends on CROS_EC
+ ---help---
+ On many Chromebooks the main PMIC is inaccessible to the AP. This is
+ often dealt with by using an I2C pass-through interface provided by
+ the EC. On some unfortunate models (e.g. Spring) the pass-through
+ is not available, and an LDO message is available instead. This
+ option enables a driver which provides very basic access to those
+ regulators, via the EC. We implement this as an I2C bus which
+ emulates just the TPS65090 messages we know about. This is done to
+ avoid duplicating the logic in the TPS65090 regulator driver for
+ enabling/disabling an LDO.
+
+config DM_I2C_GPIO
+ bool "Enable Driver Model for software emulated I2C bus driver"
+ depends on DM_I2C && DM_GPIO
+ help
+ Enable the i2c bus driver emulation by using the GPIOs. The bus GPIO
+ configuration is given by the device tree. Kernel-style device tree
+ bindings are supported.
+ Binding info: doc/device-tree-bindings/i2c/i2c-gpio.txt
+
+config SYS_I2C_FSL
+ bool "Freescale I2C bus driver"
+ depends on DM_I2C
+ help
+ Add support for Freescale I2C busses as used on MPC8240, MPC8245, and
+ MPC85xx processors.
+
+config SYS_I2C_CADENCE
+ tristate "Cadence I2C Controller"
+ depends on DM_I2C && (ARCH_ZYNQ || ARM64)
+ help
+ Say yes here to select Cadence I2C Host Controller. This controller is
+ e.g. used by Xilinx Zynq.
+
+config SYS_I2C_DW
+ bool "Designware I2C Controller"
+ default n
+ help
+ Say yes here to select the Designware I2C Host Controller. This
+ controller is used in various SoCs, e.g. the ST SPEAr, Altera
+ SoCFPGA, Synopsys ARC700 and some Intel x86 SoCs.
+
+config SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED
+ bool "DW I2C Enable Status Register not supported"
+ depends on SYS_I2C_DW && (TARGET_SPEAR300 || TARGET_SPEAR310 || \
+ TARGET_SPEAR320 || TARGET_SPEAR600 || TARGET_X600)
+ default y
+ help
+ Some versions of the Designware I2C controller do not support the
+ enable status register. This config option can be enabled in such
+ cases.
+
+config SYS_I2C_INTEL
+ bool "Intel I2C/SMBUS driver"
+ depends on DM_I2C
+ help
+ Add support for the Intel SMBUS driver. So far this driver is just
+ a stub which perhaps some basic init. There is no implementation of
+ the I2C API meaning that any I2C operations will immediately fail
+ for now.
+
+config SYS_I2C_ROCKCHIP
+ bool "Rockchip I2C driver"
+ depends on DM_I2C
+ help
+ Add support for the Rockchip I2C driver. This is used with various
+ Rockchip parts such as RK3126, RK3128, RK3036 and RK3288. All chips
+ have several I2C ports and all are provided, controled by the
+ device tree.
+
+config SYS_I2C_SANDBOX
+ bool "Sandbox I2C driver"
+ depends on SANDBOX && DM_I2C
+ help
+ Enable I2C support for sandbox. This is an emulation of a real I2C
+ bus. Devices can be attached to the bus using the device tree
+ which specifies the driver to use. As an example, see this device
+ tree fragment from sandbox.dts. It shows that the I2C bus has a
+ single EEPROM at address 0x2c (7-bit address) which is emulated by
+ the driver for "sandbox,i2c-eeprom", which is in
+ drivers/misc/i2c_eeprom_emul.c.
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ compatible = "sandbox,i2c";
+ clock-frequency = <400000>;
+ eeprom@2c {
+ reg = <0x2c>;
+ compatible = "i2c-eeprom";
+ emul {
+ compatible = "sandbox,i2c-eeprom";
+ sandbox,filename = "i2c.bin";
+ sandbox,size = <128>;
+ };
+ };
+ };
+
config SYS_I2C_UNIPHIER
bool "UniPhier I2C driver"
depends on ARCH_UNIPHIER && DM_I2C
default y
help
- Support for Panasonic UniPhier I2C controller driver. This I2C
- controller is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
+ Support for UniPhier I2C controller driver. This I2C controller
+ is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
+
+config SYS_I2C_UNIPHIER_F
+ bool "UniPhier FIFO-builtin I2C driver"
+ depends on ARCH_UNIPHIER && DM_I2C
+ default y
+ help
+ Support for UniPhier FIFO-builtin I2C controller driver.
+ This I2C controller is used on PH1-Pro4 or newer UniPhier SoCs.
+
+source "drivers/i2c/muxes/Kconfig"
+
+endmenu