efi_loader: round the memory area in efi_add_memory_map()

[oweals/u-boot.git] / drivers / fpga / zynqpl.c

diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c
index db9bd12992f9889287814d79c33b697b7666862a..21624f715ba0092a7dc9206966fa6bb21f0a81b9 100644 (file)
--- a/drivers/fpga/zynqpl.c
+++ b/drivers/fpga/zynqpl.c
@@ -1,14 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0+
 /*
  * (C) Copyright 2012-2013, Xilinx, Michal Simek
  *
  * (C) Copyright 2012
  * Joe Hershberger <joe.hershberger@ni.com>
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #include <common.h>
 #include <console.h>
+#include <cpu_func.h>
 #include <asm/io.h>
 #include <fs.h>
 #include <zynqpl.h>
@@ -18,6 +18,7 @@
 
 #define DEVCFG_CTRL_PCFG_PROG_B                0x40000000
 #define DEVCFG_CTRL_PCFG_AES_EFUSE_MASK        0x00001000
+#define DEVCFG_CTRL_PCAP_RATE_EN_MASK  0x02000000
 #define DEVCFG_ISR_FATAL_ERROR_MASK    0x00740040
 #define DEVCFG_ISR_ERROR_FLAGS_MASK    0x00340840
 #define DEVCFG_ISR_RX_FIFO_OV          0x00040000
@@ -408,10 +409,12 @@ static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize,
        if (bstype != BIT_PARTIAL)
                zynq_slcr_devcfg_enable();
 
+       puts("INFO:post config was not run, please run manually if needed\n");
+
        return FPGA_SUCCESS;
 }
 
-#if defined(CONFIG_CMD_FPGA_LOADFS)
+#if defined(CONFIG_CMD_FPGA_LOADFS) && !defined(CONFIG_SPL_BUILD)
 static int zynq_loadfs(xilinx_desc *desc, const void *buf, size_t bsize,
                       fpga_fs_info *fsinfo)
 {
@@ -421,7 +424,8 @@ static int zynq_loadfs(xilinx_desc *desc, const void *buf, size_t bsize,
        loff_t blocksize, actread;
        loff_t pos = 0;
        int fstype;
-       char *interface, *dev_part, *filename;
+       char *interface, *dev_part;
+       const char *filename;
 
        blocksize = fsinfo->blocksize;
        interface = fsinfo->interface;
@@ -494,7 +498,51 @@ static int zynq_loadfs(xilinx_desc *desc, const void *buf, size_t bsize,
 
 struct xilinx_fpga_op zynq_op = {
        .load = zynq_load,
-#if defined(CONFIG_CMD_FPGA_LOADFS)
+#if defined(CONFIG_CMD_FPGA_LOADFS) && !defined(CONFIG_SPL_BUILD)
        .loadfs = zynq_loadfs,
 #endif
 };
+
+#ifdef CONFIG_CMD_ZYNQ_AES
+/*
+ * Load the encrypted image from src addr and decrypt the image and
+ * place it back the decrypted image into dstaddr.
+ */
+int zynq_decrypt_load(u32 srcaddr, u32 srclen, u32 dstaddr, u32 dstlen)
+{
+       if (srcaddr < SZ_1M || dstaddr < SZ_1M) {
+               printf("%s: src and dst addr should be > 1M\n",
+                      __func__);
+               return FPGA_FAIL;
+       }
+
+       if (zynq_dma_xfer_init(BIT_NONE)) {
+               printf("%s: zynq_dma_xfer_init FAIL\n", __func__);
+               return FPGA_FAIL;
+       }
+
+       writel((readl(&devcfg_base->ctrl) | DEVCFG_CTRL_PCAP_RATE_EN_MASK),
+              &devcfg_base->ctrl);
+
+       debug("%s: Source = 0x%08X\n", __func__, (u32)srcaddr);
+       debug("%s: Size = %zu\n", __func__, srclen);
+
+       /* flush(clean & invalidate) d-cache range buf */
+       flush_dcache_range((u32)srcaddr, (u32)srcaddr +
+                       roundup(srclen << 2, ARCH_DMA_MINALIGN));
+       /*
+        * Flush destination address range only if image is not
+        * bitstream.
+        */
+       flush_dcache_range((u32)dstaddr, (u32)dstaddr +
+                          roundup(dstlen << 2, ARCH_DMA_MINALIGN));
+
+       if (zynq_dma_transfer(srcaddr | 1, srclen, dstaddr | 1, dstlen))
+               return FPGA_FAIL;
+
+       writel((readl(&devcfg_base->ctrl) & ~DEVCFG_CTRL_PCAP_RATE_EN_MASK),
+              &devcfg_base->ctrl);
+
+       return FPGA_SUCCESS;
+}
+#endif