/*
* cpu/ppc4xx/44x_spd_ddr2.c
* This SPD SDRAM detection code supports AMCC PPC44x cpu's with a
- * DDR2 controller (non Denali Core). Those are 440SP/SPe.
+ * DDR2 controller (non Denali Core). Those currently are:
*
- * (C) Copyright 2007
+ * 405: 405EX(r)
+ * 440/460: 440SP/440SPe/460EX/460GT
+ *
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+
+ * (C) Copyright 2007-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* COPYRIGHT AMCC CORPORATION 2004
#include <asm/io.h>
#include <asm/processor.h>
#include <asm/mmu.h>
+#include <asm/cache.h>
+
+#include "ecc.h"
#if defined(CONFIG_SPD_EEPROM) && \
- (defined(CONFIG_440SP) || defined(CONFIG_440SPE))
+ (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT))
/*-----------------------------------------------------------------------------+
* Defines
/* Defines for the Read Cycle Delay test */
#define NUMMEMTESTS 8
#define NUMMEMWORDS 8
-#define NUMLOOPS 256 /* memory test loops */
-
-#undef CONFIG_ECC_ERROR_RESET /* test-only: see description below, at check_ecc() */
+#define NUMLOOPS 64 /* memory test loops */
/*
* This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory
* memory.
*
* If at some time this restriction doesn't apply anymore, just define
- * CFG_ENABLE_SDRAM_CACHE in the board config file and this code should setup
+ * CONFIG_4xx_DCACHE in the board config file and this code should setup
* everything correctly.
*/
-#ifdef CFG_ENABLE_SDRAM_CACHE
+#ifdef CONFIG_4xx_DCACHE
#define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on SDRAM */
#else
#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */
#endif
+/*
+ * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed
+ */
+void __spd_ddr_init_hang (void)
+{
+ hang ();
+}
+void spd_ddr_init_hang (void) __attribute__((weak, alias("__spd_ddr_init_hang")));
+
+/*
+ * To provide an interface for board specific config values in this common
+ * DDR setup code, we implement he "weak" default functions here. They return
+ * the default value back to the caller.
+ *
+ * Please see include/configs/yucca.h for an example fora board specific
+ * implementation.
+ */
+u32 __ddr_wrdtr(u32 default_val)
+{
+ return default_val;
+}
+u32 ddr_wrdtr(u32) __attribute__((weak, alias("__ddr_wrdtr")));
+
+u32 __ddr_clktr(u32 default_val)
+{
+ return default_val;
+}
+u32 ddr_clktr(u32) __attribute__((weak, alias("__ddr_clktr")));
+
+
/* Private Structure Definitions */
/* enum only to ease code for cas latency setting */
* Prototypes
*-----------------------------------------------------------------------------*/
static unsigned long sdram_memsize(void);
-void program_tlb(u32 phys_addr, u32 virt_addr, u32 size, u32 tlb_word2_i_value);
static void get_spd_info(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks);
#else
static void DQS_calibration_process(void);
#endif
-#if defined(DEBUG)
static void ppc440sp_sdram_register_dump(void);
-#endif
int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
void dcbz_area(u32 start_address, u32 num_bytes);
-void dflush(void);
static u32 mfdcr_any(u32 dcr)
{
unsigned char spd1[MAX_SPD_BYTES];
unsigned char *dimm_spd[MAXDIMMS];
unsigned long dimm_populated[MAXDIMMS];
- unsigned long num_dimm_banks; /* on board dimm banks */
+ unsigned long num_dimm_banks; /* on board dimm banks */
unsigned long val;
- ddr_cas_id_t selected_cas;
+ ddr_cas_id_t selected_cas = DDR_CAS_5; /* preset to silence compiler */
int write_recovery;
unsigned long dram_size = 0;
*-----------------------------------------------------------------*/
mfsdram(SDRAM_WRDTR, val);
mtsdram(SDRAM_WRDTR, (val & ~(SDRAM_WRDTR_LLWP_MASK | SDRAM_WRDTR_WTR_MASK)) |
- (SDRAM_WRDTR_LLWP_1_CYC | SDRAM_WRDTR_WTR_90_DEG_ADV));
+ ddr_wrdtr(SDRAM_WRDTR_LLWP_1_CYC | SDRAM_WRDTR_WTR_90_DEG_ADV));
/*------------------------------------------------------------------
* Set the SDRAM Clock Timing Register
*-----------------------------------------------------------------*/
mfsdram(SDRAM_CLKTR, val);
-#ifdef CFG_44x_DDR2_CKTR_180
- mtsdram(SDRAM_CLKTR, (val & ~SDRAM_CLKTR_CLKP_MASK) | SDRAM_CLKTR_CLKP_180_DEG_ADV);
-#else
- mtsdram(SDRAM_CLKTR, (val & ~SDRAM_CLKTR_CLKP_MASK) | SDRAM_CLKTR_CLKP_0_DEG);
-#endif
+ mtsdram(SDRAM_CLKTR, (val & ~SDRAM_CLKTR_CLKP_MASK) |
+ ddr_clktr(SDRAM_CLKTR_CLKP_0_DEG));
/*------------------------------------------------------------------
* Program the BxCF registers.
dram_size = sdram_memsize();
/* and program tlb entries for this size (dynamic) */
- program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE);
+
+ /*
+ * Program TLB entries with caches enabled, for best performace
+ * while auto-calibrating and ECC generation
+ */
+ program_tlb(0, 0, dram_size, 0);
/*------------------------------------------------------------------
* DQS calibration.
/*------------------------------------------------------------------
* If ecc is enabled, initialize the parity bits.
*-----------------------------------------------------------------*/
- program_ecc(dimm_populated, iic0_dimm_addr, num_dimm_banks, MY_TLB_WORD2_I_ENABLE);
+ program_ecc(dimm_populated, iic0_dimm_addr, num_dimm_banks, 0);
#endif
-#ifdef DEBUG
+ /*
+ * Now after initialization (auto-calibration and ECC generation)
+ * remove the TLB entries with caches enabled and program again with
+ * desired cache functionality
+ */
+ remove_tlb(0, dram_size);
+ program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE);
+
ppc440sp_sdram_register_dump();
-#endif
+
+ /*
+ * Clear potential errors resulting from auto-calibration.
+ * If not done, then we could get an interrupt later on when
+ * exceptions are enabled.
+ */
+ set_mcsr(get_mcsr());
return dram_size;
}
if (dimm_found == FALSE) {
printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
-#ifdef CONFIG_ADD_RAM_INFO
void board_add_ram_info(int use_default)
{
- PPC440_SYS_INFO board_cfg;
+ PPC4xx_SYS_INFO board_cfg;
u32 val;
if (is_ecc_enabled())
val = (val & SDRAM_MMODE_DCL_MASK) >> 4;
printf(", CL%d)", val);
}
-#endif
/*------------------------------------------------------------------
* For the memory DIMMs installed, this routine verifies that they
"slot %d.\n", (unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 2:
printf("ERROR: EDO DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 3:
printf("ERROR: Pipelined Nibble DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 4:
printf("ERROR: SDRAM DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 5:
printf("ERROR: Multiplexed ROM DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 6:
printf("ERROR: SGRAM DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 7:
debug("DIMM slot %d: DDR1 SDRAM detected\n", dimm_num);
(unsigned int)dimm_num);
printf("Only DDR1 and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
}
}
&& (dimm_populated[dimm_num] != SDRAM_NONE)
&& (dimm_populated[dimm_num-1] != dimm_populated[dimm_num])) {
printf("ERROR: DIMM's DDR1 and DDR2 type can not be mixed.\n");
- hang();
+ spd_ddr_init_hang ();
}
}
}
unsigned long calc_cycle_time;
unsigned long sdram_freq;
unsigned long sdr_ddrpll;
- PPC440_SYS_INFO board_cfg;
+ PPC4xx_SYS_INFO board_cfg;
/*------------------------------------------------------------------
* Get the board configuration info.
(unsigned int)(calc_cycle_time*10));
printf("Replace the DIMM, or change DDR frequency via "
"strapping bits.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
}
"slot %d is not supported.\n", dimm_rank, dimm_num);
printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
} else
total_rank += dimm_rank;
}
"for all slots.\n", (unsigned int)total_rank);
printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
printf("Remove one of the DIMM modules.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
}
printf("This DIMM is 5.0 Volt/TTL.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x01:
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("This DIMM is LVTTL.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x02:
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("This DIMM is 1.5 Volt.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x03:
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("This DIMM is 3.3 Volt/TTL.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x04:
/* 2.5 Voltage only for DDR1 */
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
}
}
if ((dimm_populated[0] != SDRAM_NONE) && (dimm_populated[1] != SDRAM_NONE)) {
if (buf0 != buf1) {
printf("ERROR: DIMM's buffered/unbuffered, registered, clocking don't match.\n");
- hang();
+ spd_ddr_init_hang ();
}
}
if ((dimm_64bit == TRUE) && (dimm_32bit == TRUE)) {
printf("ERROR: Cannot mix 32 bit and 64 bit DDR-SDRAM DIMMs together.\n");
- hang();
+ spd_ddr_init_hang ();
}
else if ((dimm_64bit == TRUE) && (dimm_32bit == FALSE)) {
mcopt1 |= SDRAM_MCOPT1_DMWD_64;
mcopt1 |= SDRAM_MCOPT1_DMWD_32;
} else {
printf("ERROR: Please install only 32 or 64 bit DDR-SDRAM DIMMs.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
if (ecc_enabled == TRUE)
break;
default:
printf("ERROR: ucode error on selected_cas value %d", selected_cas);
- hang();
+ spd_ddr_init_hang ();
break;
}
break;
default:
printf("ERROR: write recovery not support (%d)", write_recovery);
- hang();
+ spd_ddr_init_hang ();
break;
}
#else
ods = ODS_REDUCED;
} else {
printf("ERROR: Unsupported number of DIMM's (%d)", total_dimm);
- hang();
+ spd_ddr_init_hang ();
}
mr = CMD_EMR | SELECT_MR | BURST_LEN_4 | wr | cas;
mtsdram(SDRAM_INITPLR13, 0x80800000 | emr); /* EMR OCD Exit */
} else {
printf("ERROR: ucode error as unknown DDR type in program_initplr");
- hang();
+ spd_ddr_init_hang ();
}
}
unsigned long max_4_0_tcyc_ns_x_100;
unsigned long max_5_0_tcyc_ns_x_100;
unsigned long cycle_time_ns_x_100[3];
- PPC440_SYS_INFO board_cfg;
+ PPC4xx_SYS_INFO board_cfg;
unsigned char cas_2_0_available;
unsigned char cas_2_5_available;
unsigned char cas_3_0_available;
} else {
printf("ERROR: SPD reported Tcyc is incorrect for DIMM "
"in slot %d\n", (unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
}
} else {
/* Convert from hex to decimal */
printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n");
printf("Only DIMMs DDR1 with CAS latencies of 2.0, 2.5, and 3.0 are supported.\n");
printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
} else { /* DDR2 */
debug("cas_3_0_available=%d\n", cas_3_0_available);
cas_3_0_available, cas_4_0_available, cas_5_0_available);
printf("sdram_freq=%d cycle3=%d cycle4=%d cycle5=%d\n\n",
sdram_freq, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk);
- hang();
+ spd_ddr_init_hang ();
}
}
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks)
{
- PPC440_SYS_INFO board_cfg;
+ PPC4xx_SYS_INFO board_cfg;
unsigned long max_refresh_rate;
unsigned long dimm_num;
unsigned long refresh_rate_type;
printf("ERROR: DIMM %d unsupported refresh rate/type.\n",
(unsigned int)dimm_num);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
}
unsigned long sdram_freq;
unsigned long sdr_ddrpll;
- PPC440_SYS_INFO board_cfg;
+ PPC4xx_SYS_INFO board_cfg;
/*------------------------------------------------------------------
* Get the board configuration info.
/*------------------------------------------------------------------
* Set the BxCF regs. First, wipe out the bank config registers.
*-----------------------------------------------------------------*/
- mtdcr(SDRAMC_CFGADDR, SDRAM_MB0CF);
- mtdcr(SDRAMC_CFGDATA, 0x00000000);
- mtdcr(SDRAMC_CFGADDR, SDRAM_MB1CF);
- mtdcr(SDRAMC_CFGDATA, 0x00000000);
- mtdcr(SDRAMC_CFGADDR, SDRAM_MB2CF);
- mtdcr(SDRAMC_CFGDATA, 0x00000000);
- mtdcr(SDRAMC_CFGADDR, SDRAM_MB3CF);
- mtdcr(SDRAMC_CFGDATA, 0x00000000);
+ mtsdram(SDRAM_MB0CF, 0x00000000);
+ mtsdram(SDRAM_MB1CF, 0x00000000);
+ mtsdram(SDRAM_MB2CF, 0x00000000);
+ mtsdram(SDRAM_MB3CF, 0x00000000);
mode = SDRAM_BXCF_M_BE_ENABLE;
if (num_banks == 4)
ind = 0;
else
- ind = 5;
+ ind = 5 << 8;
switch (num_col_addr) {
case 0x08:
mode |= (SDRAM_BXCF_M_AM_0 + ind);
printf("ERROR: Unsupported value for number of "
"column addresses: %d.\n", (unsigned int)num_col_addr);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
bank_0_populated = 1;
for (ind_rank = 0; ind_rank < num_ranks; ind_rank++) {
- mtdcr(SDRAMC_CFGADDR, SDRAM_MB0CF + ((dimm_num + bank_0_populated + ind_rank) << 2));
- mtdcr(SDRAMC_CFGDATA, mode);
+ mtsdram(SDRAM_MB0CF +
+ ((dimm_num + bank_0_populated + ind_rank) << 2),
+ mode);
}
}
}
unsigned long baseadd_size;
unsigned long i;
unsigned long bank_0_populated = 0;
+ unsigned long total_size = 0;
/*------------------------------------------------------------------
* Reset the rank_base_address.
* Set the sizes
*-----------------------------------------------------------------*/
baseadd_size = 0;
- rank_size_bytes = 4 * 1024 * 1024 * rank_size_id;
switch (rank_size_id) {
+ case 0x01:
+ baseadd_size |= SDRAM_RXBAS_SDSZ_1024;
+ total_size = 1024;
+ break;
case 0x02:
- baseadd_size |= SDRAM_RXBAS_SDSZ_8;
+ baseadd_size |= SDRAM_RXBAS_SDSZ_2048;
+ total_size = 2048;
break;
case 0x04:
- baseadd_size |= SDRAM_RXBAS_SDSZ_16;
+ baseadd_size |= SDRAM_RXBAS_SDSZ_4096;
+ total_size = 4096;
break;
case 0x08:
baseadd_size |= SDRAM_RXBAS_SDSZ_32;
+ total_size = 32;
break;
case 0x10:
baseadd_size |= SDRAM_RXBAS_SDSZ_64;
+ total_size = 64;
break;
case 0x20:
baseadd_size |= SDRAM_RXBAS_SDSZ_128;
+ total_size = 128;
break;
case 0x40:
baseadd_size |= SDRAM_RXBAS_SDSZ_256;
+ total_size = 256;
break;
case 0x80:
baseadd_size |= SDRAM_RXBAS_SDSZ_512;
+ total_size = 512;
break;
default:
printf("DDR-SDRAM: DIMM %d memory queue configuration.\n",
printf("ERROR: Unsupported value for the banksize: %d.\n",
(unsigned int)rank_size_id);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
+ rank_size_bytes = total_size << 20;
if ((dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_num == 1))
bank_0_populated = 1;
}
}
}
+
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ /*
+ * Enable high bandwidth access on 460EX/GT.
+ * This should/could probably be done on other
+ * PPC's too, like 440SPe.
+ * This is currently not used, but with this setup
+ * it is possible to use it later on in e.g. the Linux
+ * EMAC driver for performance gain.
+ */
+ mtdcr(SDRAM_PLBADDULL, 0x00000000); /* MQ0_BAUL */
+ mtdcr(SDRAM_PLBADDUHB, 0x00000008); /* MQ0_BAUH */
+#endif
}
/*-----------------------------------------------------------------------------+
return;
}
-#ifdef CONFIG_ECC_ERROR_RESET
-/*
- * Check for ECC errors and reset board upon any error here
- *
- * On the Katmai 440SPe eval board, from time to time, the first
- * lword write access after DDR2 initializazion with ECC checking
- * enabled, leads to an ECC error. I couldn't find a configuration
- * without this happening. On my board with the current setup it
- * happens about 1 from 10 times.
- *
- * The ECC modules used for testing are:
- * - Kingston ValueRAM KVR667D2E5/512 (tested with 1 and 2 DIMM's)
- *
- * This has to get fixed for the Katmai and tested for the other
- * board (440SP/440SPe) that will eventually use this code in the
- * future.
- *
- * 2007-03-01, sr
- */
-static void check_ecc(void)
-{
- u32 val;
-
- mfsdram(SDRAM_ECCCR, val);
- if (val != 0) {
- printf("\nECC error: MCIF0_ECCES=%08lx MQ0_ESL=%08lx address=%08lx\n",
- val, mfdcr(0x4c), mfdcr(0x4e));
- printf("ECC error occured, resetting board...\n");
- do_reset(NULL, 0, 0, NULL);
- }
-}
-#endif
-
static void wait_ddr_idle(void)
{
u32 val;
} else {
/* ECC bit set method for cached memory */
dcbz_area(start_address, num_bytes);
- dflush();
+ /* Write modified dcache lines back to memory */
+ clean_dcache_range(start_address, start_address + num_bytes);
}
blank_string(strlen(str));
sync();
eieio();
wait_ddr_idle();
-
-#ifdef CONFIG_ECC_ERROR_RESET
- /*
- * One write to 0 is enough to trigger this ECC error
- * (see description above)
- */
- out_be32(0, 0x12345678);
- check_ecc();
-#endif
}
}
#endif
* Read sample cycle auto-update enable
*-----------------------------------------------------------------*/
- /*
- * Modified for the Katmai platform: with some DIMMs, the DDR2
- * controller automatically selects the T2 read cycle, but this
- * proves unreliable. Go ahead and force the DDR2 controller
- * to use the T4 sample and disable the automatic update of the
- * RDSS field.
- */
mfsdram(SDRAM_RDCC, val);
mtsdram(SDRAM_RDCC,
(val & ~(SDRAM_RDCC_RDSS_MASK | SDRAM_RDCC_RSAE_MASK))
- | (SDRAM_RDCC_RDSS_T4 | SDRAM_RDCC_RSAE_DISABLE));
+ | SDRAM_RDCC_RSAE_ENABLE);
/*------------------------------------------------------------------
* Program RQDC register
{
unsigned long rfdc_reg;
unsigned long rffd;
- unsigned long rqdc_reg;
- unsigned long rqfd;
unsigned long val;
- long rqfd_average;
long rffd_average;
long max_start;
long min_end;
long max_end;
unsigned char fail_found;
unsigned char pass_found;
+#if !defined(CONFIG_DDR_RQDC_FIXED)
+ u32 rqdc_reg;
+ u32 rqfd;
u32 rqfd_start;
+ u32 rqfd_average;
+ int loopi = 0;
char str[] = "Auto calibration -";
char slash[] = "\\|/-\\|/-";
- int loopi = 0;
/*------------------------------------------------------------------
* Test to determine the best read clock delay tuning bits.
mfsdram(SDRAM_RQDC, rqdc_reg);
mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
SDRAM_RQDC_RQFD_ENCODE(rqfd_start));
+#else /* CONFIG_DDR_RQDC_FIXED */
+ /*
+ * On Katmai the complete auto-calibration somehow doesn't seem to
+ * produce the best results, meaning optimal values for RQFD/RFFD.
+ * This was discovered by GDA using a high bandwidth scope,
+ * analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
+ * so now on Katmai "only" RFFD is auto-calibrated.
+ */
+ mtsdram(SDRAM_RQDC, CONFIG_DDR_RQDC_FIXED);
+#endif /* CONFIG_DDR_RQDC_FIXED */
max_start = 0;
min_end = 0;
/* now fix RFDC[RFFD] found and find RQDC[RQFD] */
mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd_average));
+#if !defined(CONFIG_DDR_RQDC_FIXED)
max_pass_length = 0;
max_start = 0;
max_end = 0;
printf("\nERROR: Cannot determine a common read delay for the "
"DIMM(s) installed.\n");
debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__);
- hang();
+ ppc440sp_sdram_register_dump();
+ spd_ddr_init_hang ();
}
- blank_string(strlen(str));
-
if (rqfd_average < 0)
rqfd_average = 0;
(rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
SDRAM_RQDC_RQFD_ENCODE(rqfd_average));
+ blank_string(strlen(str));
+#endif /* CONFIG_DDR_RQDC_FIXED */
+
+ /*
+ * Now complete RDSS configuration as mentioned on page 7 of the AMCC
+ * PowerPC440SP/SPe DDR2 application note:
+ * "DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
+ */
+ mfsdram(SDRAM_RTSR, val);
+ if ((val & SDRAM_RTSR_TRK1SM_MASK) == SDRAM_RTSR_TRK1SM_ATPLS1) {
+ mfsdram(SDRAM_RDCC, val);
+ if ((val & SDRAM_RDCC_RDSS_MASK) != SDRAM_RDCC_RDSS_T4) {
+ val += 0x40000000;
+ mtsdram(SDRAM_RDCC, val);
+ }
+ }
+
mfsdram(SDRAM_DLCR, val);
debug("%s[%d] DLCR: 0x%08X\n", __FUNCTION__, __LINE__, val);
mfsdram(SDRAM_RQDC, val);
debug("%s[%d] RQDC: 0x%08X\n", __FUNCTION__, __LINE__, val);
mfsdram(SDRAM_RFDC, val);
debug("%s[%d] RFDC: 0x%08X\n", __FUNCTION__, __LINE__, val);
+ mfsdram(SDRAM_RDCC, val);
+ debug("%s[%d] RDCC: 0x%08X\n", __FUNCTION__, __LINE__, val);
}
#else /* calibration test with hardvalues */
/*-----------------------------------------------------------------------------+
if (window_found == FALSE) {
printf("ERROR: Cannot determine a common read delay for the "
"DIMM(s) installed.\n");
- hang();
+ spd_ddr_init_hang ();
}
/*------------------------------------------------------------------
dcr_data = mfdcr(SDRAM_R3BAS);
printf(" MQ3_B0BAS = 0x%08X\n", dcr_data);
}
-#endif
-#endif /* CONFIG_SPD_EEPROM */
+#else /* !defined(DEBUG) */
+static void ppc440sp_sdram_register_dump(void)
+{
+}
+#endif /* defined(DEBUG) */
+#elif defined(CONFIG_405EX)
+/*-----------------------------------------------------------------------------
+ * Function: initdram
+ * Description: Configures the PPC405EX(r) DDR1/DDR2 SDRAM memory
+ * banks. The configuration is performed using static, compile-
+ * time parameters.
+ *---------------------------------------------------------------------------*/
+long initdram(int board_type)
+{
+ /*
+ * Only run this SDRAM init code once. For NAND booting
+ * targets like Kilauea, we call initdram() early from the
+ * 4k NAND booting image (CONFIG_NAND_SPL) from nand_boot().
+ * Later on the NAND U-Boot image runs (CONFIG_NAND_U_BOOT)
+ * which calls initdram() again. This time the controller
+ * mustn't be reconfigured again since we're already running
+ * from SDRAM.
+ */
+#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+ unsigned long val;
+
+ /* Set Memory Bank Configuration Registers */
+
+ mtsdram(SDRAM_MB0CF, CFG_SDRAM0_MB0CF);
+ mtsdram(SDRAM_MB1CF, CFG_SDRAM0_MB1CF);
+ mtsdram(SDRAM_MB2CF, CFG_SDRAM0_MB2CF);
+ mtsdram(SDRAM_MB3CF, CFG_SDRAM0_MB3CF);
+
+ /* Set Memory Clock Timing Register */
+
+ mtsdram(SDRAM_CLKTR, CFG_SDRAM0_CLKTR);
+
+ /* Set Refresh Time Register */
+
+ mtsdram(SDRAM_RTR, CFG_SDRAM0_RTR);
+
+ /* Set SDRAM Timing Registers */
+
+ mtsdram(SDRAM_SDTR1, CFG_SDRAM0_SDTR1);
+ mtsdram(SDRAM_SDTR2, CFG_SDRAM0_SDTR2);
+ mtsdram(SDRAM_SDTR3, CFG_SDRAM0_SDTR3);
+
+ /* Set Mode and Extended Mode Registers */
+
+ mtsdram(SDRAM_MMODE, CFG_SDRAM0_MMODE);
+ mtsdram(SDRAM_MEMODE, CFG_SDRAM0_MEMODE);
+
+ /* Set Memory Controller Options 1 Register */
+
+ mtsdram(SDRAM_MCOPT1, CFG_SDRAM0_MCOPT1);
+
+ /* Set Manual Initialization Control Registers */
+
+ mtsdram(SDRAM_INITPLR0, CFG_SDRAM0_INITPLR0);
+ mtsdram(SDRAM_INITPLR1, CFG_SDRAM0_INITPLR1);
+ mtsdram(SDRAM_INITPLR2, CFG_SDRAM0_INITPLR2);
+ mtsdram(SDRAM_INITPLR3, CFG_SDRAM0_INITPLR3);
+ mtsdram(SDRAM_INITPLR4, CFG_SDRAM0_INITPLR4);
+ mtsdram(SDRAM_INITPLR5, CFG_SDRAM0_INITPLR5);
+ mtsdram(SDRAM_INITPLR6, CFG_SDRAM0_INITPLR6);
+ mtsdram(SDRAM_INITPLR7, CFG_SDRAM0_INITPLR7);
+ mtsdram(SDRAM_INITPLR8, CFG_SDRAM0_INITPLR8);
+ mtsdram(SDRAM_INITPLR9, CFG_SDRAM0_INITPLR9);
+ mtsdram(SDRAM_INITPLR10, CFG_SDRAM0_INITPLR10);
+ mtsdram(SDRAM_INITPLR11, CFG_SDRAM0_INITPLR11);
+ mtsdram(SDRAM_INITPLR12, CFG_SDRAM0_INITPLR12);
+ mtsdram(SDRAM_INITPLR13, CFG_SDRAM0_INITPLR13);
+ mtsdram(SDRAM_INITPLR14, CFG_SDRAM0_INITPLR14);
+ mtsdram(SDRAM_INITPLR15, CFG_SDRAM0_INITPLR15);
+
+ /* Set On-Die Termination Registers */
+
+ mtsdram(SDRAM_CODT, CFG_SDRAM0_CODT);
+ mtsdram(SDRAM_MODT0, CFG_SDRAM0_MODT0);
+ mtsdram(SDRAM_MODT1, CFG_SDRAM0_MODT1);
+
+ /* Set Write Timing Register */
+
+ mtsdram(SDRAM_WRDTR, CFG_SDRAM0_WRDTR);
+
+ /*
+ * Start Initialization by SDRAM0_MCOPT2[SREN] = 0 and
+ * SDRAM0_MCOPT2[IPTR] = 1
+ */
+
+ mtsdram(SDRAM_MCOPT2, (SDRAM_MCOPT2_SREN_EXIT |
+ SDRAM_MCOPT2_IPTR_EXECUTE));
+
+ /*
+ * Poll SDRAM0_MCSTAT[MIC] for assertion to indicate the
+ * completion of initialization.
+ */
+
+ do {
+ mfsdram(SDRAM_MCSTAT, val);
+ } while ((val & SDRAM_MCSTAT_MIC_MASK) != SDRAM_MCSTAT_MIC_COMP);
+
+ /* Set Delay Control Registers */
+
+ mtsdram(SDRAM_DLCR, CFG_SDRAM0_DLCR);
+ mtsdram(SDRAM_RDCC, CFG_SDRAM0_RDCC);
+ mtsdram(SDRAM_RQDC, CFG_SDRAM0_RQDC);
+ mtsdram(SDRAM_RFDC, CFG_SDRAM0_RFDC);
+
+ /*
+ * Enable Controller by SDRAM0_MCOPT2[DCEN] = 1:
+ */
+
+ mfsdram(SDRAM_MCOPT2, val);
+ mtsdram(SDRAM_MCOPT2, val | SDRAM_MCOPT2_DCEN_ENABLE);
+
+#if defined(CONFIG_DDR_ECC)
+ ecc_init(CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20);
+#endif /* defined(CONFIG_DDR_ECC) */
+#endif /* !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */
+
+ return (CFG_MBYTES_SDRAM << 20);
+}
+#endif /* defined(CONFIG_SPD_EEPROM) && defined(CONFIG_440SP) || ... */