arm: at91: arm926ejs/u-boot-spl.lds: Add _image_binary_end to SPL lds

[oweals/u-boot.git] / configs / sama5d3xek_nandflash_defconfig

diff --git a/configs/sama5d3xek_nandflash_defconfig b/configs/sama5d3xek_nandflash_defconfig
index d71ccd42e56273ef0d6c319e31543f6f2547607b..ddae1c8e93e001488a0080eefd088bffd306eefc 100644 (file)
--- a/configs/sama5d3xek_nandflash_defconfig
+++ b/configs/sama5d3xek_nandflash_defconfig
@@ -8,11 +8,13 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
 CONFIG_SPL=y
-CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek"
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
 CONFIG_DEBUG_UART=y
 CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_NR_DRAM_BANKS=1
 CONFIG_FIT=y
 CONFIG_NAND_BOOT=y
 CONFIG_BOOTDELAY=3
@@ -21,6 +23,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(boots
 # CONFIG_CONSOLE_MUX is not set
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL_NAND_SUPPORT=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
 # CONFIG_CMD_IMI is not set
@@ -37,6 +40,7 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_FAT=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek"
 CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
@@ -53,8 +57,15 @@ CONFIG_AT91_GPIO=y
 CONFIG_DM_MMC=y
 CONFIG_GENERIC_ATMEL_MCI=y
 CONFIG_MTD_NOR_FLASH=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_SYS_FLASH_PROTECTION=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_NAND_ATMEL=y
+CONFIG_PMECC_CAP=4
+CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
+CONFIG_SF_DEFAULT_SPEED=30000000
 CONFIG_SPI_FLASH_ATMEL=y
 CONFIG_DM_ETH=y
 CONFIG_MACB=y
@@ -63,9 +74,6 @@ CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_AT91=y
 CONFIG_DM_SERIAL=y
 CONFIG_DEBUG_UART_ATMEL=y
-CONFIG_DEBUG_UART_BASE=0xffffee00
-CONFIG_DEBUG_UART_CLOCK=132000000
-CONFIG_DEBUG_UART_BOARD_INIT=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
 CONFIG_SPI=y