spl: rename config item SPL_ATF_SUPPORT to SPL_ATF

[oweals/u-boot.git] / common / spl / Kconfig

diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 582b685dad36b9cea6298481d49ceb214e8a5926..3169bbb888a6e1bb6e9e32bc2098bae43df93923 100644 (file)
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -94,6 +94,7 @@ config SPL_STACK_R
 config SPL_STACK_R_ADDR
        depends on SPL_STACK_R
        hex "SDRAM location for SPL stack"
+       default 0x82000000 if ARCH_OMAP2PLUS
        help
          Specify the address in SDRAM for the SPL stack. This will be set up
          before board_init_r() is called.
@@ -141,11 +142,12 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
        default 0x50 if ARCH_SUNXI
        default 0x75 if ARCH_DAVINCI
        default 0x8a if ARCH_MX6
-       default 0x100 if ARCH_ROCKCHIP || ARCH_UNIPHIER
+       default 0x100 if ARCH_UNIPHIER
        default 0x140 if ARCH_MVEBU
        default 0x200 if ARCH_SOCFPGA || ARCH_AT91
        default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \
                         OMAP54XX || AM33XX || AM43XX
+       default 0x4000 if ARCH_ROCKCHIP
        help
          Address on the MMC to load U-Boot from, when the MMC is being used
          in raw mode. Units: MMC sectors (1 sector = 512 bytes).
@@ -603,6 +605,14 @@ config SPL_SPI_SUPPORT
          enable SPI drivers that are needed for other purposes also, such
          as a SPI PMIC.
 
+config SPL_THERMAL
+       bool "Driver support for thermal devices"
+       help
+         Enable support for temperature-sensing devices. Some SoCs have on-chip
+         temperature sensors to permit warnings, speed throttling or even
+         automatic power-off when the temperature gets too high or low. Other
+         devices may be discrete but connected on a suitable bus.
+
 config SPL_USB_HOST_SUPPORT
        bool "Support USB host drivers"
        help
@@ -668,6 +678,12 @@ config SPL_DFU_RAM
 
 endchoice
 
+config SPL_USB_SDP_SUPPORT
+       bool "Support SDP (Serial Download Protocol)"
+       help
+         Enable Serial Download Protocol (SDP) device support in SPL. This
+         allows to download images into memory and execute (jump to) them
+         using the same protocol as implemented by the i.MX family's boot ROM.
 endif
 
 config SPL_WATCHDOG_SUPPORT
@@ -686,11 +702,11 @@ config SPL_YMODEM_SUPPORT
          means of transmitting U-Boot over a serial line for using in SPL,
          with a checksum to ensure correctness.
 
-config SPL_ATF_SUPPORT
+config SPL_ATF
        bool "Support ARM Trusted Firmware"
        depends on ARM64
        help
-         ATF(ARM Trusted Firmware) is a component for ARM arch64 which which
+         ATF(ARM Trusted Firmware) is a component for ARM arch64 which
          is loaded by SPL(which is considered as BL2 in ATF terminology).
          More detail at: https://github.com/ARM-software/arm-trusted-firmware