spl: Allow tiny printf() to be controlled in SPL and TPL

[oweals/u-boot.git] / common / spl / Kconfig

diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 630491699cc68cea2c2529d246cb7a1ae8cb13d4..048b85ba7a2d8446cab3dc6289355a048e83f3d6 100644 (file)
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -115,7 +115,7 @@ if SPL
 
 config SPL_HANDOFF
        bool "Pass hand-off information from SPL to U-Boot proper"
-       depends on HANDOFF
+       depends on HANDOFF && SPL_BLOBLIST
        default y
        help
          This option enables SPL to write handoff information. This can be
@@ -208,6 +208,7 @@ config SPL_SYS_MALLOC_SIMPLE
 config TPL_SYS_MALLOC_SIMPLE
        bool
        prompt "Only use malloc_simple functions in the TPL"
+       depends on TPL
        help
          Say Y here to only use the *_simple malloc functions from
          malloc_simple.c, rather then using the versions from dlmalloc.c;
@@ -261,6 +262,7 @@ config SPL_BANNER_PRINT
 
 config TPL_BANNER_PRINT
        bool "Enable output of the TPL banner 'U-Boot TPL ...'"
+       depends on TPL
        default y
        help
          If this option is enabled, SPL will not print the banner with version
@@ -433,6 +435,7 @@ config SPL_HASH_SUPPORT
 
 config TPL_HASH_SUPPORT
        bool "Support hashing drivers in TPL"
+       depends on TPL
        select SHA1
        select SHA256
        help
@@ -960,7 +963,7 @@ config SPL_SERIAL_SUPPORT
          for displaying messages while SPL is running. It also brings in
          printf() and panic() functions. This should normally be enabled
          unless there are space reasons not to. Even then, consider
-         enabling USE_TINY_PRINTF which is a small printf() version.
+         enabling SPL_USE_TINY_PRINTF which is a small printf() version.
 
 config SPL_SPI_FLASH_SUPPORT
        bool "Support SPI flash drivers"
@@ -1000,6 +1003,14 @@ config SPL_SPI_LOAD
 
 endif # SPL_SPI_FLASH_SUPPORT
 
+config SYS_SPI_U_BOOT_OFFS
+       hex "address of u-boot payload in SPI flash"
+       default 0x0
+       depends on SPL_SPI_LOAD || SPL_SPI_SUNXI
+       help
+        Address within SPI-Flash from where the u-boot payload is fetched
+        from.
+
 config SPL_SPI_SUPPORT
        bool "Support SPI drivers"
        help
@@ -1146,6 +1157,23 @@ config SPL_OPTEE
          OP-TEE is an open source Trusted OS  which is loaded by SPL.
          More detail at: https://github.com/OP-TEE/optee_os
 
+config SPL_OPENSBI
+       bool "Support RISC-V OpenSBI"
+       depends on RISCV && SPL_RISCV_MMODE && RISCV_SMODE
+       help
+         OpenSBI is an open-source implementation of the RISC-V Supervisor Binary
+         Interface (SBI) specification. U-Boot supports the OpenSBI FW_DYNAMIC
+         firmware. It is loaded and started by U-Boot SPL.
+
+         More details are available at https://github.com/riscv/opensbi and
+         https://github.com/riscv/riscv-sbi-doc
+
+config SPL_OPENSBI_LOAD_ADDR
+       hex "OpenSBI load address"
+       depends on SPL_OPENSBI
+       help
+         Load address of the OpenSBI binary.
+
 config TPL
        bool
        depends on SUPPORT_TPL
@@ -1157,7 +1185,7 @@ if TPL
 
 config TPL_HANDOFF
        bool "Pass hand-off information from TPL to SPL and U-Boot proper"
-       depends on HANDOFF
+       depends on HANDOFF && TPL_BLOBLIST
        default y
        help
          This option enables TPL to write handoff information. This can be