/*
- * (C) Copyright 2000-2002
+ * (C) Copyright 2000-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
#include <command.h>
#include <image.h>
#include <asm/byteorder.h>
+
#if defined(CONFIG_IDE_8xx_DIRECT) || defined(CONFIG_IDE_PCMCIA)
# include <pcmcia.h>
#endif
+
#ifdef CONFIG_8xx
# include <mpc8xx.h>
#endif
+
+#ifdef CONFIG_MPC5xxx
+#include <mpc5xxx.h>
+#endif
+
#include <ide.h>
#include <ata.h>
-#include <cmd_ide.h>
-#include <cmd_disk.h>
+
#ifdef CONFIG_STATUS_LED
# include <status_led.h>
#endif
-#ifdef __I386__
+
+#ifndef __PPC__
#include <asm/io.h>
+#ifdef __MIPS__
+/* Macros depend on this variable */
+unsigned long mips_io_port_base = 0;
+#endif
#endif
#ifdef CONFIG_SHOW_BOOT_PROGRESS
# define SHOW_BOOT_PROGRESS(arg)
#endif
+#ifdef CONFIG_IDE_8xx_DIRECT
+DECLARE_GLOBAL_DATA_PTR;
+#endif
-#undef IDE_DEBUG
-
-
-#ifdef IDE_DEBUG
-#define PRINTF(fmt,args...) printf (fmt ,##args)
+#ifdef __PPC__
+# define EIEIO __asm__ volatile ("eieio")
+# define SYNC __asm__ volatile ("sync")
#else
-#define PRINTF(fmt,args...)
+# define EIEIO /* nothing */
+# define SYNC /* nothing */
#endif
#if (CONFIG_COMMANDS & CFG_CMD_IDE)
+#ifdef CONFIG_IDE_8xx_DIRECT
/* Timings for IDE Interface
*
* SETUP / LENGTH / HOLD - cycles valid for 50 MHz clk
#define PCMCIA_MK_CLKS( t, T ) (( (t) * (T) + 999U ) / 1000U )
+#endif /* CONFIG_IDE_8xx_DIRECT */
+
/* ------------------------------------------------------------------------- */
/* Current I/O Device */
#endif
};
-#ifdef __PPC__
+
#define ATA_CURR_BASE(dev) (CFG_ATA_BASE_ADDR+ide_bus_offset[IDE_BUS(dev)])
-#endif
#ifndef CONFIG_AMIGAONEG3SE
-static int ide_bus_ok[CFG_IDE_MAXBUS];
+static int ide_bus_ok[CFG_IDE_MAXBUS];
#else
-static int ide_bus_ok[CFG_IDE_MAXBUS] = {0,};
+static int ide_bus_ok[CFG_IDE_MAXBUS] = {0,};
#endif
-static block_dev_desc_t ide_dev_desc[CFG_IDE_MAXDEVICE];
+block_dev_desc_t ide_dev_desc[CFG_IDE_MAXDEVICE];
/* ------------------------------------------------------------------------- */
#ifdef CONFIG_IDE_LED
-#ifndef CONFIG_KUP4K
+#if !defined(CONFIG_KUP4K) && !defined(CONFIG_KUP4X) &&!defined(CONFIG_BMS2003) &&!defined(CONFIG_CPC45)
static void ide_led (uchar led, uchar status);
#else
extern void ide_led (uchar led, uchar status);
static void __inline__ ide_outb(int dev, int port, unsigned char val);
static unsigned char __inline__ ide_inb(int dev, int port);
-#ifdef __PPC__
-static void input_swap_data(int dev, ulong *sect_buf, int words);
-#endif
static void input_data(int dev, ulong *sect_buf, int words);
static void output_data(int dev, ulong *sect_buf, int words);
static void ident_cpy (unsigned char *dest, unsigned char *src, unsigned int len);
#ifdef CONFIG_ATAPI
static void atapi_inquiry(block_dev_desc_t *dev_desc);
-ulong atapi_read (int device, ulong blknr, ulong blkcnt, ulong *buffer);
+ulong atapi_read (int device, lbaint_t blknr, ulong blkcnt, void *buffer);
#endif
#ifdef CONFIG_IDE_8xx_DIRECT
static void set_pcmcia_timing (int pmode);
-#else
-#define set_pcmcia_timing(a) /* dummy */
#endif
/* ------------------------------------------------------------------------- */
if (strcmp(argv[1],"read") == 0) {
ulong addr = simple_strtoul(argv[2], NULL, 16);
- ulong blk = simple_strtoul(argv[3], NULL, 16);
ulong cnt = simple_strtoul(argv[4], NULL, 16);
ulong n;
+#ifdef CFG_64BIT_STRTOUL
+ lbaint_t blk = simple_strtoull(argv[3], NULL, 16);
+
+ printf ("\nIDE read: device %d block # %qd, count %ld ... ",
+ curr_device, blk, cnt);
+#else
+ lbaint_t blk = simple_strtoul(argv[3], NULL, 16);
printf ("\nIDE read: device %d block # %ld, count %ld ... ",
curr_device, blk, cnt);
+#endif
n = ide_dev_desc[curr_device].block_read (curr_device,
blk, cnt,
}
} else if (strcmp(argv[1],"write") == 0) {
ulong addr = simple_strtoul(argv[2], NULL, 16);
- ulong blk = simple_strtoul(argv[3], NULL, 16);
ulong cnt = simple_strtoul(argv[4], NULL, 16);
ulong n;
+#ifdef CFG_64BIT_STRTOUL
+ lbaint_t blk = simple_strtoull(argv[3], NULL, 16);
+
+ printf ("\nIDE write: device %d block # %qd, count %ld ... ",
+ curr_device, blk, cnt);
+#else
+ lbaint_t blk = simple_strtoul(argv[3], NULL, 16);
printf ("\nIDE write: device %d block # %ld, count %ld ... ",
curr_device, blk, cnt);
+#endif
n = ide_write (curr_device, blk, cnt, (ulong *)addr);
char *boot_device = NULL;
char *ep;
int dev, part = 0;
- ulong cnt;
- ulong addr;
+ ulong addr, cnt, checksum;
disk_partition_t info;
image_header_t *hdr;
int rcode = 0;
SHOW_BOOT_PROGRESS (-1);
return 1;
}
- if (strncmp(info.type, BOOT_PART_TYPE, sizeof(info.type)) != 0) {
+ if ((strncmp((char *)info.type, BOOT_PART_TYPE, sizeof(info.type)) != 0) &&
+ (strncmp((char *)info.type, BOOT_PART_COMP, sizeof(info.type)) != 0)) {
printf ("\n** Invalid partition type \"%.32s\""
" (expect \"" BOOT_PART_TYPE "\")\n",
info.type);
"Name: %.32s Type: %.32s\n",
dev, part, info.name, info.type);
- PRINTF ("First Block: %ld, # of blocks: %ld, Block Size: %ld\n",
+ debug ("First Block: %ld, # of blocks: %ld, Block Size: %ld\n",
info.start, info.size, info.blksz);
if (ide_dev_desc[dev].block_read (dev, info.start, 1, (ulong *)addr) != 1) {
hdr = (image_header_t *)addr;
- if (ntohl(hdr->ih_magic) == IH_MAGIC) {
-
- print_image_hdr (hdr);
-
- cnt = (ntohl(hdr->ih_size) + sizeof(image_header_t));
- cnt += info.blksz - 1;
- cnt /= info.blksz;
- cnt -= 1;
- } else {
+ if (ntohl(hdr->ih_magic) != IH_MAGIC) {
printf("\n** Bad Magic Number **\n");
SHOW_BOOT_PROGRESS (-1);
return 1;
}
+ checksum = ntohl(hdr->ih_hcrc);
+ hdr->ih_hcrc = 0;
+
+ if (crc32 (0, (uchar *)hdr, sizeof(image_header_t)) != checksum) {
+ puts ("\n** Bad Header Checksum **\n");
+ SHOW_BOOT_PROGRESS (-2);
+ return 1;
+ }
+ hdr->ih_hcrc = htonl(checksum); /* restore checksum for later use */
+
+ print_image_hdr (hdr);
+
+ cnt = (ntohl(hdr->ih_size) + sizeof(image_header_t));
+ cnt += info.blksz - 1;
+ cnt /= info.blksz;
+ cnt -= 1;
+
if (ide_dev_desc[dev].block_read (dev, info.start+1, cnt,
(ulong *)(addr+info.blksz)) != cnt) {
printf ("** Read error on %d:%d\n", dev, part);
void ide_init (void)
{
- DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_IDE_8xx_DIRECT
volatile immap_t *immr = (immap_t *)CFG_IMMR;
#endif
unsigned char c;
int i, bus;
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+ unsigned int ata_reset_time;
+#endif
#ifdef CONFIG_AMIGAONEG3SE
unsigned int max_bus_scan;
- unsigned int ata_reset_time;
char *s;
#endif
+#ifdef CONFIG_IDE_8xx_PCCARD
+ extern int pcmcia_on (void);
+ extern int ide_devices_found; /* Initialized in check_ide_device() */
+#endif /* CONFIG_IDE_8xx_PCCARD */
+
+#ifdef CONFIG_IDE_PREINIT
+ extern int ide_preinit (void);
+ WATCHDOG_RESET();
+
+ if (ide_preinit ()) {
+ puts ("ide_preinit failed\n");
+ return;
+ }
+#endif /* CONFIG_IDE_PREINIT */
#ifdef CONFIG_IDE_8xx_PCCARD
extern int pcmcia_on (void);
+ extern int ide_devices_found; /* Initialized in check_ide_device() */
WATCHDOG_RESET();
+ ide_devices_found = 0;
/* initialize the PCMCIA IDE adapter card */
- if (pcmcia_on())
+ pcmcia_on();
+ if (!ide_devices_found)
return;
udelay (1000000); /* 1 s */
#endif /* CONFIG_IDE_8xx_PCCARD */
WATCHDOG_RESET();
+#ifdef CONFIG_IDE_8xx_DIRECT
/* Initialize PIO timing tables */
for (i=0; i <= IDE_MAX_PIO_MODE; ++i) {
- pio_config_clk[i].t_setup = PCMCIA_MK_CLKS(pio_config_ns[i].t_setup,
- gd->bus_clk);
- pio_config_clk[i].t_length = PCMCIA_MK_CLKS(pio_config_ns[i].t_length,
- gd->bus_clk);
- pio_config_clk[i].t_hold = PCMCIA_MK_CLKS(pio_config_ns[i].t_hold,
- gd->bus_clk);
- PRINTF ("PIO Mode %d: setup=%2d ns/%d clk"
- " len=%3d ns/%d clk"
- " hold=%2d ns/%d clk\n",
- i,
- pio_config_ns[i].t_setup, pio_config_clk[i].t_setup,
- pio_config_ns[i].t_length, pio_config_clk[i].t_length,
- pio_config_ns[i].t_hold, pio_config_clk[i].t_hold);
+ pio_config_clk[i].t_setup = PCMCIA_MK_CLKS(pio_config_ns[i].t_setup,
+ gd->bus_clk);
+ pio_config_clk[i].t_length = PCMCIA_MK_CLKS(pio_config_ns[i].t_length,
+ gd->bus_clk);
+ pio_config_clk[i].t_hold = PCMCIA_MK_CLKS(pio_config_ns[i].t_hold,
+ gd->bus_clk);
+ debug ( "PIO Mode %d: setup=%2d ns/%d clk"
+ " len=%3d ns/%d clk"
+ " hold=%2d ns/%d clk\n",
+ i,
+ pio_config_ns[i].t_setup, pio_config_clk[i].t_setup,
+ pio_config_ns[i].t_length, pio_config_clk[i].t_length,
+ pio_config_ns[i].t_hold, pio_config_clk[i].t_hold);
}
+#endif /* CONFIG_IDE_8xx_DIRECT */
/* Reset the IDE just to be sure.
* Light LED's to show
#ifdef CONFIG_IDE_8xx_DIRECT
/* PCMCIA / IDE initialization for common mem space */
pcmp->pcmc_pgcrb = 0;
-#endif
/* start in PIO mode 0 - most relaxed timings */
pio_mode = 0;
set_pcmcia_timing (pio_mode);
+#endif /* CONFIG_IDE_8xx_DIRECT */
/*
* Wait for IDE to get ready.
#else
s = getenv("ide_maxbus");
if (s)
- max_bus_scan = simple_strtol(s, NULL, 10);
+ max_bus_scan = simple_strtol(s, NULL, 10);
else
- max_bus_scan = CFG_IDE_MAXBUS;
+ max_bus_scan = CFG_IDE_MAXBUS;
for (bus=0; bus<max_bus_scan; ++bus) {
int dev = bus * (CFG_IDE_MAXDEVICE / max_bus_scan);
#endif
+#ifdef CONFIG_IDE_8xx_PCCARD
+ /* Skip non-ide devices from probing */
+ if ((ide_devices_found & (1 << bus)) == 0) {
+ ide_led ((LED_IDE1 | LED_IDE2), 0); /* LED's off */
+ continue;
+ }
+#endif
printf ("Bus %d: ", bus);
ide_bus_ok[bus] = 0;
udelay (100000); /* 100 ms */
ide_outb (dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
udelay (100000); /* 100 ms */
-#ifdef CONFIG_AMIGAONEG3SE
- ata_reset_time = ATA_RESET_TIME;
- s = getenv("ide_reset_timeout");
- if (s) ata_reset_time = 2*simple_strtol(s, NULL, 10);
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+ if ((s = getenv("ide_reset_timeout")) != NULL)
+ ata_reset_time = simple_strtol(s, NULL, 10);
#endif
i = 0;
do {
c = ide_inb (dev, ATA_STATUS);
i++;
-#ifdef CONFIG_AMIGAONEG3SE
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
if (i > (ata_reset_time * 100)) {
#else
if (i > (ATA_RESET_TIME * 100)) {
ide_led ((LED_IDE1 | LED_IDE2), 0); /* LED's off */
#ifdef CONFIG_AMIGAONEG3SE
/* If this is the second bus, the first one was OK */
- if (bus != 0)
- {
- ide_bus_ok[bus] = 0;
- goto skip_bus;
+ if (bus != 0) {
+ ide_bus_ok[bus] = 0;
+ goto skip_bus;
}
#endif
return;
if (c & (ATA_STAT_BUSY | ATA_STAT_FAULT)) {
puts ("not available ");
- PRINTF ("Status = 0x%02X ", c);
+ debug ("Status = 0x%02X ", c);
#ifndef CONFIG_ATAPI /* ATAPI Devices do not set DRDY */
} else if ((c & ATA_STAT_READY) == 0) {
puts ("not available ");
- PRINTF ("Status = 0x%02X ", c);
+ debug ("Status = 0x%02X ", c);
#endif
} else {
puts ("OK ");
#ifdef CONFIG_IDE_LED
int led = (IDE_BUS(i) == 0) ? LED_IDE1 : LED_IDE2;
#endif
+ ide_dev_desc[i].type=DEV_TYPE_UNKNOWN;
ide_dev_desc[i].if_type=IF_TYPE_IDE;
ide_dev_desc[i].dev=i;
ide_dev_desc[i].part_type=PART_TYPE_UNKNOWN;
block_dev_desc_t * ide_get_dev(int dev)
{
- return ((block_dev_desc_t *)&ide_dev_desc[dev]);
+ return (dev < CFG_IDE_MAXDEVICE) ? &ide_dev_desc[dev] : NULL;
}
volatile pcmconf8xx_t *pcmp = &(immr->im_pcmcia);
ulong timings;
- PRINTF ("Set timing for PIO Mode %d\n", pmode);
+ debug ("Set timing for PIO Mode %d\n", pmode);
timings = PCMCIA_SHT(pio_config_clk[pmode].t_hold)
| PCMCIA_SST(pio_config_clk[pmode].t_setup)
| timings
#endif
;
- PRINTF ("PBR0: %08x POR0: %08x\n", pcmp->pcmc_pbr0, pcmp->pcmc_por0);
+ debug ("PBR0: %08x POR0: %08x\n", pcmp->pcmc_pbr0, pcmp->pcmc_por0);
pcmp->pcmc_pbr1 = CFG_PCMCIA_PBR1;
pcmp->pcmc_por1 = CFG_PCMCIA_POR1
| timings
#endif
;
- PRINTF ("PBR1: %08x POR1: %08x\n", pcmp->pcmc_pbr1, pcmp->pcmc_por1);
+ debug ("PBR1: %08x POR1: %08x\n", pcmp->pcmc_pbr1, pcmp->pcmc_por1);
pcmp->pcmc_pbr2 = CFG_PCMCIA_PBR2;
pcmp->pcmc_por2 = CFG_PCMCIA_POR2
| timings
#endif
;
- PRINTF ("PBR2: %08x POR2: %08x\n", pcmp->pcmc_pbr2, pcmp->pcmc_por2);
+ debug ("PBR2: %08x POR2: %08x\n", pcmp->pcmc_pbr2, pcmp->pcmc_por2);
pcmp->pcmc_pbr3 = CFG_PCMCIA_PBR3;
pcmp->pcmc_por3 = CFG_PCMCIA_POR3
| timings
#endif
;
- PRINTF ("PBR3: %08x POR3: %08x\n", pcmp->pcmc_pbr3, pcmp->pcmc_por3);
+ debug ("PBR3: %08x POR3: %08x\n", pcmp->pcmc_pbr3, pcmp->pcmc_por3);
/* IDE 1
*/
| timings
#endif
;
- PRINTF ("PBR4: %08x POR4: %08x\n", pcmp->pcmc_pbr4, pcmp->pcmc_por4);
+ debug ("PBR4: %08x POR4: %08x\n", pcmp->pcmc_pbr4, pcmp->pcmc_por4);
pcmp->pcmc_pbr5 = CFG_PCMCIA_PBR5;
pcmp->pcmc_por5 = CFG_PCMCIA_POR5
| timings
#endif
;
- PRINTF ("PBR5: %08x POR5: %08x\n", pcmp->pcmc_pbr5, pcmp->pcmc_por5);
+ debug ("PBR5: %08x POR5: %08x\n", pcmp->pcmc_pbr5, pcmp->pcmc_por5);
pcmp->pcmc_pbr6 = CFG_PCMCIA_PBR6;
pcmp->pcmc_por6 = CFG_PCMCIA_POR6
| timings
#endif
;
- PRINTF ("PBR6: %08x POR6: %08x\n", pcmp->pcmc_pbr6, pcmp->pcmc_por6);
+ debug ("PBR6: %08x POR6: %08x\n", pcmp->pcmc_pbr6, pcmp->pcmc_por6);
pcmp->pcmc_pbr7 = CFG_PCMCIA_PBR7;
pcmp->pcmc_por7 = CFG_PCMCIA_POR7
| timings
#endif
;
- PRINTF ("PBR7: %08x POR7: %08x\n", pcmp->pcmc_pbr7, pcmp->pcmc_por7);
+ debug ("PBR7: %08x POR7: %08x\n", pcmp->pcmc_pbr7, pcmp->pcmc_por7);
}
/* ------------------------------------------------------------------------- */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static void __inline__
ide_outb(int dev, int port, unsigned char val)
{
+ debug ("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
+ dev, port, val, (ATA_CURR_BASE(dev)+port));
+
/* Ensure I/O operations complete */
- __asm__ volatile("eieio");
+ EIEIO;
*((uchar *)(ATA_CURR_BASE(dev)+port)) = val;
-#if 0
- printf ("ide_outb: 0x%08lx <== 0x%02x\n", ATA_CURR_BASE(dev)+port, val);
-#endif
}
#else /* ! __PPC__ */
static void __inline__
ide_outb(int dev, int port, unsigned char val)
{
- outb(val, port);
+ outb(val, ATA_CURR_BASE(dev)+port);
}
#endif /* __PPC__ */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static unsigned char __inline__
ide_inb(int dev, int port)
{
uchar val;
/* Ensure I/O operations complete */
- __asm__ volatile("eieio");
+ EIEIO;
val = *((uchar *)(ATA_CURR_BASE(dev)+port));
-#if 0
- printf ("ide_inb: 0x%08lx ==> 0x%02x\n", ATA_CURR_BASE(dev)+port, val);
-#endif
+ debug ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
+ dev, port, (ATA_CURR_BASE(dev)+port), val);
return (val);
}
#else /* ! __PPC__ */
static unsigned char __inline__
ide_inb(int dev, int port)
{
- return inb(port);
+ return inb(ATA_CURR_BASE(dev)+port);
}
#endif /* __PPC__ */
#ifdef __PPC__
-__inline__ unsigned ld_le16(const volatile unsigned short *addr)
-{
- unsigned val;
-
- __asm__ __volatile__ ("lhbrx %0,0,%1" : "=r"(val) : "r"(addr), "m"(*addr));
- return val;
-}
-
-#ifdef CONFIG_AMIGAONEG3SE
+# ifdef CONFIG_AMIGAONEG3SE
static void
output_data_short(int dev, ulong *sect_buf, int words)
{
ushort *dbuf;
volatile ushort *pbuf;
-
+
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
}
if (words&1)
- *pbuf = 0;
+ *pbuf = 0;
}
-#endif
+# endif /* CONFIG_AMIGAONEG3SE */
+#endif /* __PPC_ */
+/* We only need to swap data if we are running on a big endian cpu. */
+/* But Au1x00 cpu:s already swaps data in big endian mode! */
+#if defined(__LITTLE_ENDIAN) || ( defined(CONFIG_AU1X00) && !defined(CONFIG_GTH2) )
+#define input_swap_data(x,y,z) input_data(x,y,z)
+#else
static void
input_swap_data(int dev, ulong *sect_buf, int words)
{
+#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+ uchar i;
+ volatile uchar *pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
+ volatile uchar *pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
+ ushort *dbuf = (ushort *)sect_buf;
+
+ while (words--) {
+ for (i=0; i<2; i++) {
+ *(((uchar *)(dbuf)) + 1) = *pbuf_even;
+ *(uchar *)dbuf = *pbuf_odd;
+ dbuf+=1;
+ }
+ }
+#else
volatile ushort *pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
ushort *dbuf = (ushort *)sect_buf;
+ debug("in input swap data base for read is %lx\n", (unsigned long) pbuf);
+
while (words--) {
+#ifdef __MIPS__
+ *dbuf++ = swab16p((u16*)pbuf);
+ *dbuf++ = swab16p((u16*)pbuf);
+#else
*dbuf++ = ld_le16(pbuf);
*dbuf++ = ld_le16(pbuf);
+#endif /* !MIPS */
}
+#endif
}
-#else /* ! __PPC__ */
-#define input_swap_data(x,y,z) input_data(x,y,z)
-#endif /* __PPC__ */
-
-
+#endif /* __LITTLE_ENDIAN || CONFIG_AU1X00 */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static void
output_data(int dev, ulong *sect_buf, int words)
{
+#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+ uchar *dbuf;
+ volatile uchar *pbuf_even;
+ volatile uchar *pbuf_odd;
+
+ pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
+ pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
+ dbuf = (uchar *)sect_buf;
+ while (words--) {
+ EIEIO;
+ *pbuf_even = *dbuf++;
+ EIEIO;
+ *pbuf_odd = *dbuf++;
+ EIEIO;
+ *pbuf_even = *dbuf++;
+ EIEIO;
+ *pbuf_odd = *dbuf++;
+ }
+#else
ushort *dbuf;
volatile ushort *pbuf;
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
}
+#endif
}
#else /* ! __PPC__ */
static void
output_data(int dev, ulong *sect_buf, int words)
{
- outsw(ATA_DATA_REG, sect_buf, words<<1);
+ outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words<<1);
}
#endif /* __PPC__ */
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
static void
input_data(int dev, ulong *sect_buf, int words)
{
+#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+ uchar *dbuf;
+ volatile uchar *pbuf_even;
+ volatile uchar *pbuf_odd;
+
+ pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
+ pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
+ dbuf = (uchar *)sect_buf;
+ while (words--) {
+ *dbuf++ = *pbuf_even;
+ EIEIO;
+ SYNC;
+ *dbuf++ = *pbuf_odd;
+ EIEIO;
+ SYNC;
+ *dbuf++ = *pbuf_even;
+ EIEIO;
+ SYNC;
+ *dbuf++ = *pbuf_odd;
+ EIEIO;
+ SYNC;
+ }
+#else
ushort *dbuf;
volatile ushort *pbuf;
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
+
+ debug("in input data base for read is %lx\n", (unsigned long) pbuf);
+
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
}
+#endif
}
#else /* ! __PPC__ */
static void
input_data(int dev, ulong *sect_buf, int words)
{
- insw(ATA_DATA_REG, sect_buf, words << 1);
+ insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words << 1);
}
#endif /* __PPC__ */
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
while (words--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
- __asm__ volatile ("eieio");
+ EIEIO;
}
- if (words&1)
- {
- ushort dummy;
- dummy = *pbuf;
+ if (words&1) {
+ ushort dummy;
+ dummy = *pbuf;
}
}
#endif
#ifdef CONFIG_AMIGAONEG3SE
int max_bus_scan;
- int retries = 0;
char *s;
+#endif
+#ifdef CONFIG_ATAPI
+ int retries = 0;
int do_retry = 0;
#endif
dev_desc->if_type=IF_TYPE_IDE;
#ifdef CONFIG_ATAPI
-#ifdef CONFIG_AMIGAONEG3SE
do_retry = 0;
retries = 0;
/* Warning: This will be tricky to read */
- while (retries <= 1)
- {
-#endif /* CONFIG_AMIGAONEG3SE */
-
+ while (retries <= 1) {
/* check signature */
if ((ide_inb(device,ATA_SECT_CNT) == 0x01) &&
(ide_inb(device,ATA_SECT_NUM) == 0x01) &&
* to become ready
*/
c = ide_wait (device, ATAPI_TIME_OUT);
- }
- else
+ } else
#endif
{
/* Start Ident Command
if (((c & ATA_STAT_DRQ) == 0) ||
((c & (ATA_STAT_FAULT|ATA_STAT_ERR)) != 0) ) {
+#ifdef CONFIG_ATAPI
#ifdef CONFIG_AMIGAONEG3SE
- if (retries == 0) {
- do_retry = 1;
- } else {
- dev_desc->type=DEV_TYPE_UNKNOWN;
- return;
+ s = getenv("ide_doreset");
+ if (s && strcmp(s, "on") == 0)
+#endif
+ {
+ /* Need to soft reset the device in case it's an ATAPI... */
+ debug ("Retrying...\n");
+ ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
+ udelay(100000);
+ ide_outb (device, ATA_COMMAND, 0x08);
+ udelay (500000); /* 500 ms */
}
-#else
- dev_desc->type=DEV_TYPE_UNKNOWN;
- return;
-#endif /* CONFIG_AMIGAONEG3SE */
- }
-
-#ifdef CONFIG_AMIGAONEG3SE
- s = getenv("ide_doreset");
- if (s && strcmp(s, "on") == 0 && 1 == do_retry) {
- /* Need to soft reset the device in case it's an ATAPI... */
- PRINTF("Retrying...\n");
+ /* Select device
+ */
ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
- udelay(100000);
- ide_outb (device, ATA_COMMAND, 0x08);
- udelay (100000); /* 100 ms */
retries++;
- } else {
- retries = 100;
+#else
+ return;
+#endif
}
+#ifdef CONFIG_ATAPI
+ else
+ break;
} /* see above - ugly to read */
-#endif /* CONFIG_AMIGAONEG3SE */
+
+ if (retries == 2) /* Not found */
+ return;
+#endif
input_swap_data (device, iobuf, ATA_SECTORWORDS);
ident_cpy (dev_desc->revision, iop->fw_rev, sizeof(dev_desc->revision));
ident_cpy (dev_desc->vendor, iop->model, sizeof(dev_desc->vendor));
ident_cpy (dev_desc->product, iop->serial_no, sizeof(dev_desc->product));
+#ifdef __LITTLE_ENDIAN
+ /*
+ * firmware revision and model number have Big Endian Byte
+ * order in Word. Convert both to little endian.
+ *
+ * See CF+ and CompactFlash Specification Revision 2.0:
+ * 6.2.1.6: Identfy Drive, Table 39 for more details
+ */
+
+ strswab (dev_desc->revision);
+ strswab (dev_desc->vendor);
+#endif /* __LITTLE_ENDIAN */
if ((iop->config & 0x0080)==0x0080)
dev_desc->removable = 1;
printf ("tPIO = 0x%02x = %d\n",mode, mode);
if (mode > 2) { /* 2 is maximum allowed tPIO value */
mode = 2;
- PRINTF ("Override tPIO -> 2\n");
+ debug ("Override tPIO -> 2\n");
}
if (iop->field_valid & 2) { /* drive implements ATA2? */
- PRINTF ("Drive implements ATA2\n");
+ debug ("Drive implements ATA2\n");
if (iop->capability & 8) { /* drive supports use_iordy? */
cycle_time = iop->eide_pio_iordy;
} else {
cycle_time = iop->eide_pio;
}
- PRINTF ("cycle time = %d\n", cycle_time);
+ debug ("cycle time = %d\n", cycle_time);
mode = 4;
if (cycle_time > 120) mode = 3; /* 120 ns for PIO mode 4 */
if (cycle_time > 180) mode = 2; /* 180 ns for PIO mode 3 */
}
#endif /* CONFIG_ATAPI */
+#ifdef __BIG_ENDIAN
/* swap shorts */
dev_desc->lba = (iop->lba_capacity << 16) | (iop->lba_capacity >> 16);
+#else /* ! __BIG_ENDIAN */
+ /*
+ * do not swap shorts on little endian
+ *
+ * See CF+ and CompactFlash Specification Revision 2.0:
+ * 6.2.1.6: Identfy Drive, Table 39, Word Address 57-58 for details.
+ */
+ dev_desc->lba = iop->lba_capacity;
+#endif /* __BIG_ENDIAN */
+
+#ifdef CONFIG_LBA48
+ if (iop->command_set_2 & 0x0400) { /* LBA 48 support */
+ dev_desc->lba48 = 1;
+ dev_desc->lba = (unsigned long long)iop->lba48_capacity[0] |
+ ((unsigned long long)iop->lba48_capacity[1] << 16) |
+ ((unsigned long long)iop->lba48_capacity[2] << 32) |
+ ((unsigned long long)iop->lba48_capacity[3] << 48);
+ } else {
+ dev_desc->lba48 = 0;
+ }
+#endif /* CONFIG_LBA48 */
/* assuming HD */
dev_desc->type=DEV_TYPE_HARDDISK;
dev_desc->blksz=ATA_BLOCKSIZE;
ide_outb (device, ATA_LBA_LOW, 0);
ide_outb (device, ATA_LBA_MID, 0);
ide_outb (device, ATA_LBA_HIGH, 0);
- ide_outb (device, ATA_DEV_HD, ATA_LBA |
- ATA_DEVICE(device));
+ ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
ide_outb (device, ATA_COMMAND, 0xe3);
udelay (50);
c = ide_wait (device, IDE_TIME_OUT); /* can't take over 500 ms */
/* ------------------------------------------------------------------------- */
-ulong ide_read (int device, ulong blknr, ulong blkcnt, ulong *buffer)
+ulong ide_read (int device, lbaint_t blknr, ulong blkcnt, void *buffer)
{
ulong n = 0;
unsigned char c;
unsigned char pwrsave=0; /* power save */
+#ifdef CONFIG_LBA48
+ unsigned char lba48 = 0;
- PRINTF ("ide_read dev %d start %lX, blocks %lX buffer at %lX\n",
+ if (blknr & 0x0000fffff0000000) {
+ /* more than 28 bits used, use 48bit mode */
+ lba48 = 1;
+ }
+#endif
+ debug ("ide_read dev %d start %qX, blocks %lX buffer at %lX\n",
device, blknr, blkcnt, (ulong)buffer);
ide_led (DEVICE_LED(device), 1); /* LED on */
printf ("No Powersaving mode %X\n", c);
} else {
c = ide_inb(device,ATA_SECT_CNT);
- PRINTF("Powersaving %02X\n",c);
+ debug ("Powersaving %02X\n",c);
if(c==0)
pwrsave=1;
}
printf ("IDE read: device %d not ready\n", device);
break;
}
-
+#ifdef CONFIG_LBA48
+ if (lba48) {
+ /* write high bits */
+ ide_outb (device, ATA_SECT_CNT, 0);
+ ide_outb (device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
+ ide_outb (device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
+ ide_outb (device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
+ }
+#endif
ide_outb (device, ATA_SECT_CNT, 1);
ide_outb (device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
ide_outb (device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
ide_outb (device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
- ide_outb (device, ATA_DEV_HD, ATA_LBA |
- ATA_DEVICE(device) |
- ((blknr >> 24) & 0xF) );
- ide_outb (device, ATA_COMMAND, ATA_CMD_READ);
+
+#ifdef CONFIG_LBA48
+ if (lba48) {
+ ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device) );
+ ide_outb (device, ATA_COMMAND, ATA_CMD_READ_EXT);
+
+ } else
+#endif
+ {
+ ide_outb (device, ATA_DEV_HD, ATA_LBA |
+ ATA_DEVICE(device) |
+ ((blknr >> 24) & 0xF) );
+ ide_outb (device, ATA_COMMAND, ATA_CMD_READ);
+ }
udelay (50);
}
if ((c&(ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR)) != ATA_STAT_DRQ) {
- printf ("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
+#if defined(CFG_64BIT_LBA) && defined(CFG_64BIT_VSPRINTF)
+ printf ("Error (no IRQ) dev %d blk %qd: status 0x%02x\n",
device, blknr, c);
+#else
+ printf ("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
+ device, (ulong)blknr, c);
+#endif
break;
}
++n;
++blknr;
- buffer += ATA_SECTORWORDS;
+ buffer += ATA_BLOCKSIZE;
}
IDE_READ_E:
ide_led (DEVICE_LED(device), 0); /* LED off */
/* ------------------------------------------------------------------------- */
-ulong ide_write (int device, ulong blknr, ulong blkcnt, ulong *buffer)
+ulong ide_write (int device, lbaint_t blknr, ulong blkcnt, void *buffer)
{
ulong n = 0;
unsigned char c;
+#ifdef CONFIG_LBA48
+ unsigned char lba48 = 0;
+
+ if (blknr & 0x0000fffff0000000) {
+ /* more than 28 bits used, use 48bit mode */
+ lba48 = 1;
+ }
+#endif
ide_led (DEVICE_LED(device), 1); /* LED on */
printf ("IDE read: device %d not ready\n", device);
goto WR_OUT;
}
-
+#ifdef CONFIG_LBA48
+ if (lba48) {
+ /* write high bits */
+ ide_outb (device, ATA_SECT_CNT, 0);
+ ide_outb (device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
+ ide_outb (device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
+ ide_outb (device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
+ }
+#endif
ide_outb (device, ATA_SECT_CNT, 1);
ide_outb (device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
ide_outb (device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
ide_outb (device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
- ide_outb (device, ATA_DEV_HD, ATA_LBA |
- ATA_DEVICE(device) |
- ((blknr >> 24) & 0xF) );
- ide_outb (device, ATA_COMMAND, ATA_CMD_WRITE);
+
+#ifdef CONFIG_LBA48
+ if (lba48) {
+ ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device) );
+ ide_outb (device, ATA_COMMAND, ATA_CMD_WRITE_EXT);
+
+ } else
+#endif
+ {
+ ide_outb (device, ATA_DEV_HD, ATA_LBA |
+ ATA_DEVICE(device) |
+ ((blknr >> 24) & 0xF) );
+ ide_outb (device, ATA_COMMAND, ATA_CMD_WRITE);
+ }
udelay (50);
c = ide_wait (device, IDE_TIME_OUT); /* can't take over 500 ms */
if ((c&(ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR)) != ATA_STAT_DRQ) {
- printf ("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
+#if defined(CFG_64BIT_LBA) && defined(CFG_64BIT_VSPRINTF)
+ printf ("Error (no IRQ) dev %d blk %qd: status 0x%02x\n",
device, blknr, c);
+#else
+ printf ("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
+ device, (ulong)blknr, c);
+#endif
goto WR_OUT;
}
c = ide_inb (device, ATA_STATUS); /* clear IRQ */
++n;
++blknr;
- buffer += ATA_SECTORWORDS;
+ buffer += ATA_BLOCKSIZE;
}
WR_OUT:
ide_led (DEVICE_LED(device), 0); /* LED off */
/*
* copy src to dest, skipping leading and trailing blanks and null
* terminate the string
+ * "len" is the size of available memory including the terminating '\0'
*/
-static void ident_cpy (unsigned char *dest, unsigned char *src, unsigned int len)
+static void ident_cpy (unsigned char *dst, unsigned char *src, unsigned int len)
{
- int start,end;
+ unsigned char *end, *last;
- start=0;
- while (start<len) {
- if (src[start]!=' ')
- break;
- start++;
- }
- end=len-1;
- while (end>start) {
- if (src[end]!=' ')
- break;
- end--;
- }
- for ( ; start<=end; start++) {
- *dest++=src[start];
+ last = dst;
+ end = src + len - 1;
+
+ /* reserve space for '\0' */
+ if (len < 2)
+ goto OUT;
+
+ /* skip leading white space */
+ while ((*src) && (src<end) && (*src==' '))
+ ++src;
+
+ /* copy string, omitting trailing white space */
+ while ((*src) && (src<end)) {
+ *dst++ = *src;
+ if (*src++ != ' ')
+ last = dst;
}
- *dest='\0';
+OUT:
+ *last = '\0';
}
/* ------------------------------------------------------------------------- */
/* ------------------------------------------------------------------------- */
-#if defined(CONFIG_IDE_LED) && !defined(CONFIG_AMIGAONEG3SE) && !defined(CONFIG_KUP4K)
+#if defined(CONFIG_IDE_LED) && \
+ !defined(CONFIG_AMIGAONEG3SE)&& \
+ !defined(CONFIG_CPC45) && \
+ !defined(CONFIG_HMI10) && \
+ !defined(CONFIG_KUP4K) && \
+ !defined(CONFIG_KUP4X)
static uchar led_buffer = 0; /* Buffer for current LED status */
* ATAPI Support
*/
-
-
-#undef ATAPI_DEBUG
-
-#ifdef ATAPI_DEBUG
-#define AT_PRINTF(fmt,args...) printf (fmt ,##args)
-#else
-#define AT_PRINTF(fmt,args...)
-#endif
-
-#ifdef __PPC__
+#if defined(__PPC__) || defined(CONFIG_PXA_PCMCIA)
/* since ATAPI may use commands with not 4 bytes alligned length
* we have our own transfer functions, 2 bytes alligned */
static void
output_data_shorts(int dev, ushort *sect_buf, int shorts)
{
+#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+ uchar *dbuf;
+ volatile uchar *pbuf_even;
+ volatile uchar *pbuf_odd;
+
+ pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
+ pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
+ while (shorts--) {
+ EIEIO;
+ *pbuf_even = *dbuf++;
+ EIEIO;
+ *pbuf_odd = *dbuf++;
+ }
+#else
ushort *dbuf;
volatile ushort *pbuf;
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
+
+ debug ("in output data shorts base for read is %lx\n", (unsigned long) pbuf);
+
while (shorts--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*pbuf = *dbuf++;
}
+#endif
}
static void
input_data_shorts(int dev, ushort *sect_buf, int shorts)
{
+#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+ uchar *dbuf;
+ volatile uchar *pbuf_even;
+ volatile uchar *pbuf_odd;
+
+ pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
+ pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
+ while (shorts--) {
+ EIEIO;
+ *dbuf++ = *pbuf_even;
+ EIEIO;
+ *dbuf++ = *pbuf_odd;
+ }
+#else
ushort *dbuf;
volatile ushort *pbuf;
pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
dbuf = (ushort *)sect_buf;
+
+ debug("in input data shorts base for read is %lx\n", (unsigned long) pbuf);
+
while (shorts--) {
- __asm__ volatile ("eieio");
+ EIEIO;
*dbuf++ = *pbuf;
}
+#endif
}
#else /* ! __PPC__ */
static void
output_data_shorts(int dev, ushort *sect_buf, int shorts)
{
- outsw(ATA_DATA_REG, sect_buf, shorts);
+ outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, shorts);
}
-
static void
input_data_shorts(int dev, ushort *sect_buf, int shorts)
{
- insw(ATA_DATA_REG, sect_buf, shorts);
+ insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, shorts);
}
#endif /* __PPC__ */
if ((c & mask) != res ) {
if (c & ATA_STAT_ERR) {
err=(ide_inb(device,ATA_ERROR_REG))>>4;
- AT_PRINTF("atapi_issue 1 returned sense key %X status %02X\n",err,c);
+ debug ("atapi_issue 1 returned sense key %X status %02X\n",err,c);
} else {
printf ("ATTAPI_ISSUE: (no DRQ) after sending ccb (%x) status 0x%02x\n", ccb[0],c);
err=0xFF;
goto AI_OUT;
}
if(n!=buflen) {
- AT_PRINTF("WARNING, transfer bytes %d not equal with requested %d\n",n,buflen);
+ debug ("WARNING, transfer bytes %d not equal with requested %d\n",n,buflen);
}
if(n!=0) { /* data transfer */
- AT_PRINTF("ATAPI_ISSUE: %d Bytes to transfer\n",n);
+ debug ("ATAPI_ISSUE: %d Bytes to transfer\n",n);
/* we transfer shorts */
n>>=1;
/* ok now decide if it is an in or output */
if ((ide_inb(device, ATA_SECT_CNT)&0x02)==0) {
- AT_PRINTF("Write to device\n");
+ debug ("Write to device\n");
output_data_shorts(device,(unsigned short *)buffer,n);
} else {
- AT_PRINTF("Read from device @ %p shorts %d\n",buffer,n);
+ debug ("Read from device @ %p shorts %d\n",buffer,n);
input_data_shorts(device,(unsigned short *)buffer,n);
}
}
c = atapi_wait_mask(device,ATAPI_TIME_OUT,mask,res);
if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
err=(ide_inb(device,ATA_ERROR_REG) >> 4);
- AT_PRINTF("atapi_issue 2 returned sense key %X status %X\n",err,c);
+ debug ("atapi_issue 2 returned sense key %X status %X\n",err,c);
} else {
err = 0;
}
if (res==0xFF)
return (0xFF); /* error */
- AT_PRINTF("(auto_req)atapi_issue returned sense key %X\n",res);
+ debug ("(auto_req)atapi_issue returned sense key %X\n",res);
memset(sense_ccb,0,sizeof(sense_ccb));
memset(sense_data,0,sizeof(sense_data));
asc=(sense_data[12]);
ascq=(sense_data[13]);
- AT_PRINTF("ATAPI_CMD_REQ_SENSE returned %x\n",res);
- AT_PRINTF(" Sense page: %02X key %02X ASC %02X ASCQ %02X\n",
+ debug ("ATAPI_CMD_REQ_SENSE returned %x\n",res);
+ debug (" Sense page: %02X key %02X ASC %02X ASCQ %02X\n",
sense_data[0],
key,
asc,
goto error;
}
if(asc==0x3a) {
- AT_PRINTF("Media not present\n");
+ debug ("Media not present\n");
goto error;
}
#ifdef CONFIG_AMIGAONEG3SE
if ((sense_data[2]&0xF)==0x0B) {
- AT_PRINTF("ABORTED COMMAND...retry\n");
+ debug ("ABORTED COMMAND...retry\n");
if (retrycnt++ < 4)
goto retry;
return (0xFF);
if ((sense_data[2]&0xf) == 0x02 &&
sense_data[12] == 0x04 &&
sense_data[13] == 0x01 ) {
- AT_PRINTF("Waiting for unit to become active\n");
+ debug ("Waiting for unit to become active\n");
udelay(timeout);
if (retrycnt++ < 4)
goto retry;
printf ("ERROR: Unknown Sense key %02X ASC %02X ASCQ %02X\n",key,asc,ascq);
error:
- AT_PRINTF ("ERROR Sense key %02X ASC %02X ASCQ %02X\n",key,asc,ascq);
+ debug ("ERROR Sense key %02X ASC %02X ASCQ %02X\n",key,asc,ascq);
return (0xFF);
}
-
static void atapi_inquiry(block_dev_desc_t * dev_desc)
{
unsigned char ccb[12]; /* Command descriptor block */
ccb[4]=40; /* allocation Legnth */
c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,40);
- AT_PRINTF("ATAPI_CMD_INQUIRY returned %x\n",c);
+ debug ("ATAPI_CMD_INQUIRY returned %x\n",c);
if (c!=0)
return;
c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,0);
- AT_PRINTF("ATAPI_CMD_START_STOP returned %x\n",c);
+ debug ("ATAPI_CMD_START_STOP returned %x\n",c);
if (c!=0)
return;
memset(iobuf,0,sizeof(iobuf));
c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,0);
- AT_PRINTF("ATAPI_CMD_UNIT_TEST_READY returned %x\n",c);
+ debug ("ATAPI_CMD_UNIT_TEST_READY returned %x\n",c);
if (c!=0)
return;
memset(iobuf,0,sizeof(iobuf));
ccb[0]=ATAPI_CMD_READ_CAP;
c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,8);
- AT_PRINTF("ATAPI_CMD_READ_CAP returned %x\n",c);
+ debug ("ATAPI_CMD_READ_CAP returned %x\n",c);
if (c!=0)
return;
- AT_PRINTF("Read Cap: LBA %02X%02X%02X%02X blksize %02X%02X%02X%02X\n",
+ debug ("Read Cap: LBA %02X%02X%02X%02X blksize %02X%02X%02X%02X\n",
iobuf[0],iobuf[1],iobuf[2],iobuf[3],
iobuf[4],iobuf[5],iobuf[6],iobuf[7]);
((unsigned long)iobuf[5]<<16) +
((unsigned long)iobuf[6]<< 8) +
((unsigned long)iobuf[7]);
+#ifdef CONFIG_LBA48
+ dev_desc->lba48 = 0; /* ATAPI devices cannot use 48bit addressing (ATA/ATAPI v7) */
+#endif
return;
}
#define ATAPI_READ_BLOCK_SIZE 2048 /* assuming CD part */
#define ATAPI_READ_MAX_BLOCK ATAPI_READ_MAX_BYTES/ATAPI_READ_BLOCK_SIZE /* max blocks */
-ulong atapi_read (int device, ulong blknr, ulong blkcnt, ulong *buffer)
+ulong atapi_read (int device, lbaint_t blknr, ulong blkcnt, void *buffer)
{
ulong n = 0;
unsigned char ccb[12]; /* Command descriptor block */
ulong cnt;
- AT_PRINTF("atapi_read dev %d start %lX, blocks %lX buffer at %lX\n",
+ debug ("atapi_read dev %d start %lX, blocks %lX buffer at %lX\n",
device, blknr, blkcnt, (ulong)buffer);
do {
n+=cnt;
blkcnt-=cnt;
blknr+=cnt;
- buffer+=cnt*(ATAPI_READ_BLOCK_SIZE/4); /* ulong blocksize in ulong */
+ buffer+=(cnt*ATAPI_READ_BLOCK_SIZE);
} while (blkcnt > 0);
return (n);
}
#endif /* CONFIG_ATAPI */
+U_BOOT_CMD(
+ ide, 5, 1, do_ide,
+ "ide - IDE sub-system\n",
+ "reset - reset IDE controller\n"
+ "ide info - show available IDE devices\n"
+ "ide device [dev] - show or set current device\n"
+ "ide part [dev] - print partition table of one or all IDE devices\n"
+ "ide read addr blk# cnt\n"
+ "ide write addr blk# cnt - read/write `cnt'"
+ " blocks starting at block `blk#'\n"
+ " to/from memory address `addr'\n"
+);
+
+U_BOOT_CMD(
+ diskboot, 3, 1, do_diskboot,
+ "diskboot- boot from IDE device\n",
+ "loadAddr dev:part\n"
+);
+
#endif /* CONFIG_COMMANDS & CFG_CMD_IDE */