colibri_imx6: migrate mmc to using driver model

[oweals/u-boot.git] / board / toradex / colibri_imx6 / colibri_imx6.c

diff --git a/board/toradex/colibri_imx6/colibri_imx6.c b/board/toradex/colibri_imx6/colibri_imx6.c
index 0131d9a6357bfba3927f7b4fc8eb255fd7440e30..1238474d7e39b53a64d74ec90a3b8dd9f256bf75 100644 (file)
--- a/board/toradex/colibri_imx6/colibri_imx6.c
+++ b/board/toradex/colibri_imx6/colibri_imx6.c
@@ -77,6 +77,7 @@ iomux_v3_cfg_t const uart1_pads[] = {
        MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
+#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD)
 /* Colibri MMC */
 iomux_v3_cfg_t const usdhc1_pads[] = {
        MX6_PAD_SD1_CLK__SD1_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -103,6 +104,7 @@ iomux_v3_cfg_t const usdhc3_pads[] = {
        MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
        MX6_PAD_SD3_RST__SD3_RESET  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
+#endif /* CONFIG_FSL_ESDHC & CONFIG_SPL_BUILD */
 
 iomux_v3_cfg_t const enet_pads[] = {
        MX6_PAD_ENET_MDC__ENET_MDC              | MUX_PAD_CTRL(ENET_PAD_CTRL),
@@ -310,7 +312,7 @@ int board_ehci_power(int port, int on)
 }
 #endif /* CONFIG_USB_EHCI_MX6 */
 
-#ifdef CONFIG_FSL_ESDHC
+#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD)
 /* use the following sequence: eMMC, MMC */
 struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
        {USDHC3_BASE_ADDR},
@@ -335,37 +337,6 @@ int board_mmc_getcd(struct mmc *mmc)
 
 int board_mmc_init(bd_t *bis)
 {
-#ifndef CONFIG_SPL_BUILD
-       s32 status = 0;
-       u32 index = 0;
-
-       usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-       usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-
-       usdhc_cfg[0].max_bus_width = 8;
-       usdhc_cfg[1].max_bus_width = 4;
-
-       for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
-               switch (index) {
-               case 0:
-                       imx_iomux_v3_setup_multiple_pads(
-                               usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-                       break;
-               case 1:
-                       imx_iomux_v3_setup_multiple_pads(
-                               usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
-                       break;
-               default:
-                       printf("Warning: you configured more USDHC controllers (%d) then supported by the board (%d)\n",
-                              index + 1, CONFIG_SYS_FSL_USDHC_NUM);
-                       return status;
-               }
-
-               status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
-       }
-
-       return status;
-#else /* !CONFIG_SPL_BUILD */
        struct src *psrc = (struct src *)SRC_BASE_ADDR;
        unsigned reg = readl(&psrc->sbmr1) >> 11;
        /*
@@ -397,9 +368,8 @@ int board_mmc_init(bd_t *bis)
        }
 
        return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif /* !CONFIG_SPL_BUILD */
 }
-#endif /* CONFIG_FSL_ESDHC */
+#endif /* CONFIG_FSL_ESDHC & CONFIG_SPL_BUILD */
 
 int board_phy_config(struct phy_device *phydev)
 {