arm: mach-k3: Enable dcache in SPL

[oweals/u-boot.git] / board / theadorable / theadorable.c

diff --git a/board/theadorable/theadorable.c b/board/theadorable/theadorable.c
index dd6def5e6e7910aea9d1ea0b96fbfcb5f6a4797a..621e26905ba72d1859894abf6fbb505757d29573 100644 (file)
--- a/board/theadorable/theadorable.c
+++ b/board/theadorable/theadorable.c
@@ -1,20 +1,25 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ * Copyright (C) 2015-2019 Stefan Roese <sr@denx.de>
  */
 
 #include <common.h>
+#include <console.h>
 #include <i2c.h>
+#include <init.h>
 #include <pci.h>
+#if !defined(CONFIG_SPL_BUILD)
+#include <bootcount.h>
+#endif
 #include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/soc.h>
-#include <linux/crc8.h>
 #include <linux/mbus.h>
 #ifdef CONFIG_NET
 #include <netdev.h>
 #endif
+#include <u-boot/crc.h>
 #include "theadorable.h"
 
 #include "../drivers/ddr/marvell/axp/ddr3_hw_training.h"
@@ -42,6 +47,7 @@ DECLARE_GLOBAL_DATA_PTR;
 #define STM_I2C_BUS    1
 #define STM_I2C_ADDR   0x27
 #define REBOOT_DELAY   1000            /* reboot-delay in ms */
+#define ABORT_TIMEOUT  3000            /* 3 seconds reboot abort timeout */
 
 /* DDR3 static configuration */
 static MV_DRAM_MC_INIT ddr3_theadorable[MV_MAX_DDR3_STATIC_SIZE] = {
@@ -127,15 +133,15 @@ MV_DRAM_MODES *ddr3_get_static_ddr_mode(void)
        return &board_ddr_modes[0];
 }
 
-MV_BIN_SERDES_CFG *board_serdes_cfg_get(u8 pex_mode)
+MV_BIN_SERDES_CFG *board_serdes_cfg_get(void)
 {
        return &theadorable_serdes_cfg[0];
 }
 
 u8 board_sat_r_get(u8 dev_num, u8 reg)
 {
-       /* Bit 0 enables PCI 2.0 link capabilities instead of PCI 1.x */
-       return 0x01;
+       /* Bit x enables PCI 2.0 link capabilities instead of PCI 1.x */
+       return 0xe;     /* PEX port 0 is PCIe Gen1, PEX port 1..3 PCIe Gen2 */
 }
 
 int board_early_init_f(void)
@@ -218,7 +224,7 @@ int board_eth_init(bd_t *bis)
 }
 #endif
 
-#ifdef CONFIG_BOARD_LATE_INIT
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_BOARD_LATE_INIT)
 int board_late_init(void)
 {
        pci_dev_t bdf;
@@ -232,6 +238,7 @@ int board_late_init(void)
         */
        bdf = pci_find_device(PCI_VENDOR_ID_PLX, 0x8619, 0);
        if (bdf == -1) {
+               unsigned long start_time = get_timer(0);
                u8 i2c_buf[8];
                int ret;
 
@@ -239,6 +246,28 @@ int board_late_init(void)
                bootcount = bootcount_load();
                printf("Failed to find PLX PEX-switch (bootcount=%ld)\n",
                       bootcount);
+
+               /*
+                * The user can exit this boot-loop in the error case by
+                * hitting Ctrl-C. So wait some time for this key here.
+                */
+               printf("Continue booting with Ctrl-C, otherwise rebooting\n");
+               do {
+                       /* Handle control-c and timeouts */
+                       if (ctrlc()) {
+                               printf("PEX error boot-loop aborted!\n");
+                               return 0;
+                       }
+               } while (get_timer(start_time) < ABORT_TIMEOUT);
+
+
+               /*
+                * At this stage the bootcounter has not been incremented
+                * yet. We need to do this manually here to get an actually
+                * working bootcounter in this error case.
+                */
+               bootcount_inc();
+
                if (bootcount > PEX_SWITCH_NOT_FOUNT_LIMIT) {
                        printf("Issuing power-switch via uC!\n");