slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
support for this.
-config SPL_NAND_SUPPORT
- bool "SPL/NAND mode support"
- depends on SPL
- default n
- ---help---
- This enables support for booting from NAND internal
- memory. U-Boot SPL doesn't detect where is it load from,
- therefore this option is needed to properly load image from
- flash. Option also disables MMC functionality on U-Boot due to
- initialization errors encountered, when both controllers are
- enabled.
-
config USB0_VBUS_PIN
string "Vbus enable pin for usb0 (otg)"
default ""
Set the Vbus detect pin for usb0 (otg). This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config USB0_ID_DET
+ string "ID detect pin for usb0 (otg)"
+ default ""
+ ---help---
+ Set the ID detect pin for usb0 (otg). This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config USB1_VBUS_PIN
string "Vbus enable pin for usb1 (ehci0)"
default "PH6" if MACH_SUN4I || MACH_SUN7I
Set the enable pin for the external VGA DAC. This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config VIDEO_COMPOSITE
+ boolean "Composite video output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN5I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting composite video.
+
config VIDEO_LCD_MODE
string "LCD panel timing details"
depends on VIDEO
select VIDEO_LCD_SSD2828
select VIDEO_LCD_IF_PARALLEL
---help---
- 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+ 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+
+config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
+ bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip"
+ select VIDEO_LCD_ANX9804
+ select VIDEO_LCD_IF_PARALLEL
+ select VIDEO_LCD_PANEL_I2C
+ ---help---
+ Select this for eDP LCD panels with 4 lanes running at 1.62G,
+ connected via an ANX9804 bridge chip.
config VIDEO_LCD_PANEL_HITACHI_TX18D42VM
bool "Hitachi tx18d42vm LCD panel"
endchoice
-config USB_MUSB_SUNXI
- bool "Enable sunxi OTG / DRC USB controller in host mode"
- default n
- ---help---
- Say y here to enable support for the sunxi OTG / DRC USB controller
- used on almost all sunxi boards. Note currently u-boot can only have
- one usb host controller enabled at a time, so enabling this on boards
- which also use the ehci host controller will result in build errors.
-
-config USB_KEYBOARD
- boolean "Enable USB keyboard support"
- default y
- ---help---
- Say Y here to add support for using a USB keyboard (typically used
- in combination with a graphical console).
-
config GMAC_TX_DELAY
int "GMAC Transmit Clock Delay Chain"
default 0
---help---
Set the GMAC Transmit Clock Delay Chain value.
-config SYS_MALLOC_CLEAR_ON_INIT
- default n
-
-config NET
- default y
-
-config NETDEVICES
- default y
-
-config DM_ETH
- default y
-
-config DM_SERIAL
- default y
-
-config DM_USB
- default y if !USB_MUSB_SUNXI
-
endif