config MACH_SUN7I
bool "sun7i (Allwinner A20)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN8I
bool "sun8i (Allwinner A23)"
select CPU_V7
+ select SUPPORT_SPL
endchoice
-config SYS_CONFIG_NAME
- string
- default "sun4i" if MACH_SUN4I
- default "sun5i" if MACH_SUN5I
- default "sun6i" if MACH_SUN6I
- default "sun7i" if MACH_SUN7I
- default "sun8i" if MACH_SUN8I
-
-choice
- prompt "Board"
-
-config TARGET_A10_OLINUXINO_L
- bool "A10_OLINUXINO_L"
- depends on MACH_SUN4I
-
-config TARGET_A10S_OLINUXINO_M
- bool "A10S_OLINUXINO_M"
- depends on MACH_SUN5I
-
-config TARGET_A13_OLINUXINOM
- bool "A13_OLINUXINOM"
- depends on MACH_SUN5I
-
-config TARGET_A13_OLINUXINO
- bool "A13_OLINUXINO"
- depends on MACH_SUN5I
-
-config TARGET_A20_OLINUXINO_L2
- bool "A20_OLINUXINO_L2"
- depends on MACH_SUN7I
-
-config TARGET_A20_OLINUXINO_L
- bool "A20_OLINUXINO_L"
- depends on MACH_SUN7I
-
-config TARGET_A20_OLINUXINO_M
- bool "A20_OLINUXINO_M"
- depends on MACH_SUN7I
-
-config TARGET_AUXTEK_T004
- bool "AUXTEK_T004"
- depends on MACH_SUN5I
-
-config TARGET_BANANAPI
- bool "BANANAPI"
- depends on MACH_SUN7I
-
-config TARGET_COLOMBUS
- bool "COLOMBUS"
- depends on MACH_SUN6I
-
-config TARGET_CUBIEBOARD2
- bool "CUBIEBOARD2"
- depends on MACH_SUN7I
-
-config TARGET_CUBIEBOARD
- bool "CUBIEBOARD"
- depends on MACH_SUN4I
-
-config TARGET_CUBIETRUCK
- bool "CUBIETRUCK"
- depends on MACH_SUN7I
+config DRAM_CLK
+ int "sunxi dram clock speed"
+ default 312 if MACH_SUN6I || MACH_SUN8I
+ default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+ ---help---
+ Set the dram clock speed, valid range 240 - 480, must be a multiple
+ of 24.
-config TARGET_IPPO_Q8H_V5
- bool "IPPO_Q8H_V5"
- depends on MACH_SUN8I
+if MACH_SUN5I || MACH_SUN7I
+config DRAM_MBUS_CLK
+ int "sunxi mbus clock speed"
+ default 300
+ ---help---
+ Set the mbus clock speed. The maximum on sun5i hardware is 300MHz.
-config TARGET_PCDUINO3
- bool "PCDUINO3"
- depends on MACH_SUN7I
+endif
-config TARGET_MELE_A1000G
- bool "MELE_A1000G"
- depends on MACH_SUN4I
+config DRAM_ZQ
+ int "sunxi dram zq value"
+ default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
+ default 127 if MACH_SUN7I
+ ---help---
+ Set the dram zq value.
-config TARGET_MELE_A1000
- bool "MELE_A1000"
- depends on MACH_SUN4I
+if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+config DRAM_EMR1
+ int "sunxi dram emr1 value"
+ default 0 if MACH_SUN4I
+ default 4 if MACH_SUN5I || MACH_SUN7I
+ ---help---
+ Set the dram controller emr1 value.
-config TARGET_MELE_M3
- bool "MELE_M3"
- depends on MACH_SUN7I
+config DRAM_ODT_EN
+ int "sunxi dram odt_en value"
+ default 0
+ ---help---
+ Set the dram controller odt_en parameter. This can be used to
+ enable/disable the ODT feature.
-config TARGET_MINI_X_1GB
- bool "MINI_X_1GB"
- depends on MACH_SUN4I
+config DRAM_TPR3
+ hex "sunxi dram tpr3 value"
+ default 0
+ ---help---
+ Set the dram controller tpr3 parameter. This parameter configures
+ the delay on the command lane and also phase shifts, which are
+ applied for sampling incoming read data. The default value 0
+ means that no phase/delay adjustments are necessary. Properly
+ configuring this parameter increases reliability at high DRAM
+ clock speeds.
+
+config DRAM_DQS_GATING_DELAY
+ hex "sunxi dram dqs_gating_delay value"
+ default 0
+ ---help---
+ Set the dram controller dqs_gating_delay parmeter. Each byte
+ encodes the DQS gating delay for each byte lane. The delay
+ granularity is 1/4 cycle. For example, the value 0x05060606
+ means that the delay is 5 quarter-cycles for one lane (1.25
+ cycles) and 6 quarter-cycles (1.5 cycles) for 3 other lanes.
+ The default value 0 means autodetection. The results of hardware
+ autodetection are not very reliable and depend on the chip
+ temperature (sometimes producing different results on cold start
+ and warm reboot). But the accuracy of hardware autodetection
+ is usually good enough, unless running at really high DRAM
+ clocks speeds (up to 600MHz). If unsure, keep as 0.
-config TARGET_MINI_X
- bool "MINI_X"
- depends on MACH_SUN4I
+choice
+ prompt "sunxi dram timings"
+ default DRAM_TIMINGS_VENDOR_MAGIC
+ ---help---
+ Select the timings of the DDR3 chips.
-config TARGET_BA10_TV_BOX
- bool "BA10_TV_BOX"
- depends on MACH_SUN4I
+config DRAM_TIMINGS_VENDOR_MAGIC
+ bool "Magic vendor timings from Android"
+ ---help---
+ The same DRAM timings as in the Allwinner boot0 bootloader.
-config TARGET_I12_TVBOX
- bool "I12_TVBOX"
- depends on MACH_SUN7I
+config DRAM_TIMINGS_DDR3_1066F_1333H
+ bool "JEDEC DDR3-1333H with down binning to DDR3-1066F"
+ ---help---
+ Use the timings of the standard JEDEC DDR3-1066F speed bin for
+ DRAM_CLK <= 533MHz and the timings of the DDR3-1333H speed bin
+ for DRAM_CLK > 533MHz. This covers the majority of DDR3 chips
+ used in Allwinner A10/A13/A20 devices. In the case of DDR3-1333
+ or DDR3-1600 chips, be sure to check the DRAM datasheet to confirm
+ that down binning to DDR3-1066F is supported (because DDR3-1066F
+ uses a bit faster timings than DDR3-1333H).
+
+config DRAM_TIMINGS_DDR3_800E_1066G_1333J
+ bool "JEDEC DDR3-800E / DDR3-1066G / DDR3-1333J"
+ ---help---
+ Use the timings of the slowest possible JEDEC speed bin for the
+ selected DRAM_CLK. Depending on the DRAM_CLK value, it may be
+ DDR3-800E, DDR3-1066G or DDR3-1333J.
-config TARGET_QT840A
- bool "QT840A"
- depends on MACH_SUN7I
+endchoice
-config TARGET_R7DONGLE
- bool "R7DONGLE"
- depends on MACH_SUN5I
+endif
-endchoice
+config SYS_CONFIG_NAME
+ default "sun4i" if MACH_SUN4I
+ default "sun5i" if MACH_SUN5I
+ default "sun6i" if MACH_SUN6I
+ default "sun7i" if MACH_SUN7I
+ default "sun8i" if MACH_SUN8I
config SYS_BOARD
default "sunxi"
depends on SPL
default n
+config UART0_PORT_F
+ bool "UART0 on MicroSD breakout board"
+ depends on SPL_FEL
+ default n
+ ---help---
+ Repurpose the SD card slot for getting access to the UART0 serial
+ console. Primarily useful only for low level u-boot debugging on
+ tablets, where normal UART0 is difficult to access and requires
+ device disassembly and/or soldering. As the SD card can't be used
+ at the same time, the system can be only booted in the FEL mode.
+ Only enable this if you really know what you are doing.
+
config FDTFILE
string "Default fdtfile env setting for this board"
slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
support for this.
+config USB0_VBUS_PIN
+ string "Vbus enable pin for usb0 (otg)"
+ default ""
+ ---help---
+ Set the Vbus enable pin for usb0 (otg). This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config USB1_VBUS_PIN
+ string "Vbus enable pin for usb1 (ehci0)"
+ default "PH6" if MACH_SUN4I || MACH_SUN7I
+ default "PH27" if MACH_SUN6I
+ ---help---
+ Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes
+ a string in the format understood by sunxi_name_to_gpio, e.g.
+ PH1 for pin 1 of port H.
+
+config USB2_VBUS_PIN
+ string "Vbus enable pin for usb2 (ehci1)"
+ default "PH3" if MACH_SUN4I || MACH_SUN7I
+ default "PH24" if MACH_SUN6I
+ ---help---
+ See USB1_VBUS_PIN help text.
+
+config VIDEO
+ boolean "Enable graphical uboot console on HDMI, LCD or VGA"
+ default y
+ ---help---
+ Say Y here to add support for using a cfb console on the HDMI, LCD
+ or VGA output found on most sunxi devices. See doc/README.video for
+ info on how to select the video output and mode.
+
+config VIDEO_HDMI
+ boolean "HDMI output support"
+ depends on VIDEO && !MACH_SUN8I
+ default y
+ ---help---
+ Say Y here to add support for outputting video over HDMI.
+
+config VIDEO_VGA
+ boolean "VGA output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting video over VGA.
+
+config VIDEO_VGA_VIA_LCD
+ boolean "VGA via LCD controller support"
+ depends on VIDEO && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I)
+ default n
+ ---help---
+ Say Y here to add support for external DACs connected to the parallel
+ LCD interface driving a VGA connector, such as found on the
+ Olimex A13 boards.
+
+config VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH
+ boolean "Force sync active high for VGA via LCD controller support"
+ depends on VIDEO_VGA_VIA_LCD
+ default n
+ ---help---
+ Say Y here if you've a board which uses opendrain drivers for the vga
+ hsync and vsync signals. Opendrain drivers cannot generate steep enough
+ positive edges for a stable video output, so on boards with opendrain
+ drivers the sync signals must always be active high.
+
+config VIDEO_VGA_EXTERNAL_DAC_EN
+ string "LCD panel power enable pin"
+ depends on VIDEO_VGA_VIA_LCD
+ default ""
+ ---help---
+ Set the enable pin for the external VGA DAC. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config VIDEO_LCD_MODE
+ string "LCD panel timing details"
+ depends on VIDEO
+ default ""
+ ---help---
+ LCD panel timing details string, leave empty if there is no LCD panel.
+ This is in drivers/video/videomodes.c: video_get_params() format, e.g.
+ x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
+
+config VIDEO_LCD_DCLK_PHASE
+ int "LCD panel display clock phase"
+ depends on VIDEO
+ default 1
+ ---help---
+ Select LCD panel display clock phase shift, range 0-3.
+
+config VIDEO_LCD_POWER
+ string "LCD panel power enable pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the power enable pin for the LCD panel. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config VIDEO_LCD_BL_EN
+ string "LCD panel backlight enable pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the backlight enable pin for the LCD panel. This takes a string in the
+ the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of
+ port H.
+
+config VIDEO_LCD_BL_PWM
+ string "LCD panel backlight pwm pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the backlight pwm pin for the LCD panel. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config VIDEO_LCD_BL_PWM_ACTIVE_LOW
+ bool "LCD panel backlight pwm is inverted"
+ depends on VIDEO
+ default y
+ ---help---
+ Set this if the backlight pwm output is active low.
+
+
+# Note only one of these may be selected at a time! But hidden choices are
+# not supported by Kconfig
+config VIDEO_LCD_IF_PARALLEL
+ bool
+
+config VIDEO_LCD_IF_LVDS
+ bool
+
+
+choice
+ prompt "LCD panel support"
+ depends on VIDEO
+ ---help---
+ Select which type of LCD panel to support.
+
+config VIDEO_LCD_PANEL_PARALLEL
+ bool "Generic parallel interface LCD panel"
+ select VIDEO_LCD_IF_PARALLEL
+
+config VIDEO_LCD_PANEL_LVDS
+ bool "Generic lvds interface LCD panel"
+ select VIDEO_LCD_IF_LVDS
+
+config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828
+ bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip"
+ select VIDEO_LCD_SSD2828
+ select VIDEO_LCD_IF_PARALLEL
+ ---help---
+ 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+
+config VIDEO_LCD_PANEL_HITACHI_TX18D42VM
+ bool "Hitachi tx18d42vm LCD panel"
+ select VIDEO_LCD_HITACHI_TX18D42VM
+ select VIDEO_LCD_IF_LVDS
+ ---help---
+ 7.85" 1024x768 Hitachi tx18d42vm LCD panel support
+
+endchoice
+
+
+config USB_MUSB_SUNXI
+ bool "Enable sunxi OTG / DRC USB controller in host mode"
+ default n
+ ---help---
+ Say y here to enable support for the sunxi OTG / DRC USB controller
+ used on almost all sunxi boards. Note currently u-boot can only have
+ one usb host controller enabled at a time, so enabling this on boards
+ which also use the ehci host controller will result in build errors.
+
+config USB_KEYBOARD
+ boolean "Enable USB keyboard support"
+ default y
+ ---help---
+ Say Y here to add support for using a USB keyboard (typically used
+ in combination with a graphical console).
+
+config GMAC_TX_DELAY
+ int "GMAC Transmit Clock Delay Chain"
+ default 0
+ ---help---
+ Set the GMAC Transmit Clock Delay Chain value.
+
endif