ARM: socfpga: vining_fpga: Rename VINING|FPGA

[oweals/u-boot.git] / board / samtec / vining_fpga / socfpga.c

diff --git a/board/samtec/vining_fpga/socfpga.c b/board/samtec/vining_fpga/socfpga.c
deleted file mode 100644 (file)
index 1e095a4..0000000
--- a/board/samtec/vining_fpga/socfpga.c
+++ /dev/null
@@ -1,93 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- *  Copyright (C) 2012 Altera Corporation <www.altera.com>
- */
-
-#include <common.h>
-#include <env.h>
-#include <asm/arch/reset_manager.h>
-#include <asm/io.h>
-#include <asm/gpio.h>
-#include <i2c.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-int board_late_init(void)
-{
-       const unsigned int phy_nrst_gpio = 0;
-       const unsigned int usb_nrst_gpio = 35;
-       int ret;
-
-       status_led_set(1, CONFIG_LED_STATUS_ON);
-       status_led_set(2, CONFIG_LED_STATUS_ON);
-
-       /* Address of boot parameters for ATAG (if ATAG is used) */
-       gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
-       ret = gpio_request(phy_nrst_gpio, "phy_nrst_gpio");
-       if (!ret)
-               gpio_direction_output(phy_nrst_gpio, 1);
-       else
-               printf("Cannot remove PHY from reset!\n");
-
-       ret = gpio_request(usb_nrst_gpio, "usb_nrst_gpio");
-       if (!ret)
-               gpio_direction_output(usb_nrst_gpio, 1);
-       else
-               printf("Cannot remove USB from reset!\n");
-
-       mdelay(50);
-
-       return 0;
-}
-
-#ifndef CONFIG_SPL_BUILD
-int misc_init_r(void)
-{
-       uchar data[128];
-       char str[32];
-       u32 serial;
-       int ret;
-
-       /* EEPROM is at address 0x50 (at bus CONFIG_SYS_EEPROM_BUS_NUM). */
-       ret = eeprom_read(0x50, 0, data, sizeof(data));
-       if (ret) {
-               puts("Cannot read I2C EEPROM.\n");
-               return 0;
-       }
-
-       /* Check EEPROM signature. */
-       if (!(data[0] == 0xa5 && data[1] == 0x5a)) {
-               puts("Invalid I2C EEPROM signature.\n");
-               env_set("unit_serial", "invalid");
-               env_set("unit_ident", "VINing-xxxx-STD");
-               env_set("hostname", "vining-invalid");
-               return 0;
-       }
-
-       /* If 'unit_serial' is already set, do nothing. */
-       if (!env_get("unit_serial")) {
-               /* This field is Big Endian ! */
-               serial = (data[0x54] << 24) | (data[0x55] << 16) |
-                        (data[0x56] << 8) | (data[0x57] << 0);
-               memset(str, 0, sizeof(str));
-               sprintf(str, "%07i", serial);
-               env_set("unit_serial", str);
-       }
-
-       if (!env_get("unit_ident")) {
-               memset(str, 0, sizeof(str));
-               memcpy(str, &data[0x2e], 18);
-               env_set("unit_ident", str);
-       }
-
-       /* Set ethernet address from EEPROM. */
-       if (!env_get("ethaddr") && is_valid_ethaddr(&data[0x62]))
-               eth_env_set_enetaddr("ethaddr", &data[0x62]);
-
-       return 0;
-}
-#endif