T210: Add support for 64-bit T210-based P2571 board

[oweals/u-boot.git] / board / nvidia / p2571 / max77620_init.c

diff --git a/board/nvidia/p2571/max77620_init.c b/board/nvidia/p2571/max77620_init.c
new file mode 100644 (file)
index 0000000..ed8d4dc
--- /dev/null
+++ b/board/nvidia/p2571/max77620_init.c
@@ -0,0 +1,85 @@
+/*
+ * (C) Copyright 2013-2015
+ * NVIDIA Corporation <www.nvidia.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch-tegra/tegra_i2c.h>
+#include "max77620_init.h"
+
+/* MAX77620-PMIC-specific early init code - get CPU rails up, etc */
+
+void tegra_i2c_ll_write_addr(uint addr, uint config)
+{
+       struct i2c_ctlr *reg = (struct i2c_ctlr *)TEGRA_DVC_BASE;
+
+       writel(addr, &reg->cmd_addr0);
+       writel(config, &reg->cnfg);
+}
+
+void tegra_i2c_ll_write_data(uint data, uint config)
+{
+       struct i2c_ctlr *reg = (struct i2c_ctlr *)TEGRA_DVC_BASE;
+
+       writel(data, &reg->cmd_data1);
+       writel(config, &reg->cnfg);
+}
+
+void pmic_enable_cpu_vdd(void)
+{
+       uint reg;
+       debug("%s entry\n", __func__);
+
+       /* Setup/Enable GPIO5 - VDD_CPU_REG_EN */
+       debug("%s: Setting GPIO5 to enable CPU regulator\n", __func__);
+       /* B3=1=logic high,B2=dontcare,B1=0=output,B0=1=push-pull */
+       reg = 0x0900 | MAX77620_GPIO5_REG;
+       tegra_i2c_ll_write_addr(MAX77620_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(reg, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+
+       /* Setup/Enable GPIO1 - VDD_HDMI_5V0_BST_EN */
+       debug("%s: Setting GPIO1 to enable HDMI\n", __func__);
+       reg = 0x0900 | MAX77620_GPIO1_REG;
+       tegra_i2c_ll_write_addr(MAX77620_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(reg, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+
+       /* GPIO 0,1,5,6,7 = GPIO, 2,3,4 = alt mode */
+       reg = 0x1C00 | MAX77620_AME_GPIO;
+       tegra_i2c_ll_write_addr(MAX77620_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(reg, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+
+       /* Disable SD1 Remote Sense, Set SD1 for LPDDR4 to 1.125v */
+       debug("%s: Set SD1 for LPDDR4, disable SD1RS, voltage to 1.125v\n",
+             __func__);
+       /* bit1=0, SD1 remote sense disabled */
+       reg = 0x0400 | MAX77620_CNFG2SD_REG;
+       tegra_i2c_ll_write_addr(MAX77620_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(reg, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+
+       /* SD1 output = 1.125V */
+       reg = 0x2A00 | MAX77620_SD1_REG;
+       tegra_i2c_ll_write_addr(MAX77620_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(reg, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+
+       debug("%s: Set LDO2 for VDDIO_SDMMC_AP power to 3.3V\n", __func__);
+       /* 0xF2 for 3.3v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
+       reg = 0xF200 | MAX77620_CNFG1_L2_REG;
+       tegra_i2c_ll_write_addr(MAX77620_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(reg, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+
+       debug("%s: Set LDO1 for USB3 phy power to 1.05V??\n", __func__);
+       /* 0xCA for 105v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
+       reg = 0xCA00 | MAX77620_CNFG1_L1_REG;
+       tegra_i2c_ll_write_addr(MAX77620_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(reg, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+}