#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <asm/arch/hmatrix.h>
+#include <asm/arch/portmux.h>
#include <lcd.h>
-#define SM_PM_GCCTRL 0x0060
+#include "../../../cpu/at32ap/hsmc3.h"
DECLARE_GLOBAL_DATA_PTR;
/* Enable SDRAM in the EBI mux */
hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
- gpio_enable_ebi();
- gpio_enable_usart1();
-
- /* enable higher address lines for larger flash devices */
- gpio_select_periph_A(GPIO_PIN_PE16, 0); /* ADDR23 */
- gpio_select_periph_A(GPIO_PIN_PE17, 0); /* ADDR24 */
- gpio_select_periph_A(GPIO_PIN_PE18, 0); /* ADDR25 */
-
- /* enable data flash chip select */
- gpio_select_periph_A(GPIO_PIN_PE25, 0); /* NCS2 */
+ /* Enable 26 address bits and NCS2 */
+ portmux_enable_ebi(16, 26, PORTMUX_EBI_CS(2), PORTMUX_DRIVE_HIGH);
+ portmux_enable_usart1(PORTMUX_DRIVE_MIN);
/* de-assert "force sys reset" pin */
- gpio_set_value(GPIO_PIN_PD15, 1); /* FORCE RESET */
- gpio_select_pio(GPIO_PIN_PD15, GPIOF_OUTPUT);
+ portmux_select_gpio(PORTMUX_PORT_D, 1 << 15,
+ PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
/* init custom i/o */
/* cpu type inputs */
- gpio_select_pio(GPIO_PIN_PE19, 0);
- gpio_select_pio(GPIO_PIN_PE20, 0);
- gpio_select_pio(GPIO_PIN_PE23, 0);
+ portmux_select_gpio(PORTMUX_PORT_E, (1 << 19) | (1 << 20) | (1 << 23),
+ PORTMUX_DIR_INPUT);
/* main board type inputs */
- gpio_select_pio(GPIO_PIN_PB19, 0);
- gpio_select_pio(GPIO_PIN_PB29, 0);
+ portmux_select_gpio(PORTMUX_PORT_B, (1 << 19) | (1 << 29),
+ PORTMUX_DIR_INPUT);
/* DEBUG input (use weak pullup) */
- gpio_select_pio(GPIO_PIN_PE21, GPIOF_PULLUP);
+ portmux_select_gpio(PORTMUX_PORT_E, 1 << 21,
+ PORTMUX_DIR_INPUT | PORTMUX_PULL_UP);
/* are we suppressing the console ? */
- if (gpio_get_value(GPIO_PIN_PE21) == 1)
- gd->flags |= GD_FLG_SILENT;
+ if (gpio_get_value(GPIO_PIN_PE(21)) == 1)
+ gd->flags |= (GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE);
/* reset phys */
- gpio_select_pio(GPIO_PIN_PE24, 0);
- gpio_set_value(GPIO_PIN_PC18, 1); /* PHY RESET */
- gpio_select_pio(GPIO_PIN_PC18, GPIOF_OUTPUT);
-
- /* GCLK0 - 10MHz clock */
- writel(0x00000004, (void *)SM_BASE + SM_PM_GCCTRL);
- gpio_select_periph_A(GPIO_PIN_PA30, 0);
+ portmux_select_gpio(PORTMUX_PORT_E, 1 << 24, PORTMUX_DIR_INPUT);
+ portmux_select_gpio(PORTMUX_PORT_C, 1 << 18,
+ PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
udelay(5000);
/* release phys reset */
- gpio_set_value(GPIO_PIN_PC18, 0); /* PHY RESET (Release) */
+ gpio_set_value(GPIO_PIN_PC(18), 0); /* PHY RESET (Release) */
+
+ /* setup Data Flash chip select (NCS2) */
+ hsmc3_writel(MODE2, 0x20121003);
+ hsmc3_writel(CYCLE2, 0x000a0009);
+ hsmc3_writel(PULSE2, 0x0a060806);
+ hsmc3_writel(SETUP2, 0x00030102);
+
+ /* setup FRAM chip select (NCS3) */
+ hsmc3_writel(MODE3, 0x10120001);
+ hsmc3_writel(CYCLE3, 0x001e001d);
+ hsmc3_writel(PULSE3, 0x08040704);
+ hsmc3_writel(SETUP3, 0x02050204);
#if defined(CONFIG_MACB)
/* init macb0 pins */
- gpio_select_periph_A(GPIO_PIN_PC3, 0); /* TXD0 */
- gpio_select_periph_A(GPIO_PIN_PC4, 0); /* TXD1 */
- gpio_select_periph_A(GPIO_PIN_PC7, 0); /* TXEN */
- gpio_select_periph_A(GPIO_PIN_PC8, 0); /* TXCK */
- gpio_select_periph_A(GPIO_PIN_PC9, 0); /* RXD0 */
- gpio_select_periph_A(GPIO_PIN_PC10, 0); /* RXD1 */
- gpio_select_periph_A(GPIO_PIN_PC13, 0); /* RXER */
- gpio_select_periph_A(GPIO_PIN_PC15, 0); /* RXDV */
- gpio_select_periph_A(GPIO_PIN_PC16, 0); /* MDC */
- gpio_select_periph_A(GPIO_PIN_PC17, 0); /* MDIO */
-#if !defined(CONFIG_RMII)
- gpio_select_periph_A(GPIO_PIN_PC0, 0); /* COL */
- gpio_select_periph_A(GPIO_PIN_PC1, 0); /* CRS */
- gpio_select_periph_A(GPIO_PIN_PC2, 0); /* TXER */
- gpio_select_periph_A(GPIO_PIN_PC5, 0); /* TXD2 */
- gpio_select_periph_A(GPIO_PIN_PC6, 0); /* TXD3 */
- gpio_select_periph_A(GPIO_PIN_PC11, 0); /* RXD2 */
- gpio_select_periph_A(GPIO_PIN_PC12, 0); /* RXD3 */
- gpio_select_periph_A(GPIO_PIN_PC14, 0); /* RXCK */
-#endif
-
- /* init macb1 pins */
- gpio_select_periph_B(GPIO_PIN_PD13, 0); /* TXD0 */
- gpio_select_periph_B(GPIO_PIN_PD14, 0); /* TXD1 */
- gpio_select_periph_B(GPIO_PIN_PD11, 0); /* TXEN */
- gpio_select_periph_B(GPIO_PIN_PD12, 0); /* TXCK */
- gpio_select_periph_B(GPIO_PIN_PD10, 0); /* RXD0 */
- gpio_select_periph_B(GPIO_PIN_PD6, 0); /* RXD1 */
- gpio_select_periph_B(GPIO_PIN_PD5, 0); /* RXER */
- gpio_select_periph_B(GPIO_PIN_PD4, 0); /* RXDV */
- gpio_select_periph_B(GPIO_PIN_PD3, 0); /* MDC */
- gpio_select_periph_B(GPIO_PIN_PD2, 0); /* MDIO */
-#if !defined(CONFIG_RMII)
- gpio_select_periph_B(GPIO_PIN_PC19, 0); /* COL */
- gpio_select_periph_B(GPIO_PIN_PC23, 0); /* CRS */
- gpio_select_periph_B(GPIO_PIN_PC26, 0); /* TXER */
- gpio_select_periph_B(GPIO_PIN_PC27, 0); /* TXD2 */
- gpio_select_periph_B(GPIO_PIN_PC28, 0); /* TXD3 */
- gpio_select_periph_B(GPIO_PIN_PC29, 0); /* RXD2 */
- gpio_select_periph_B(GPIO_PIN_PC30, 0); /* RXD3 */
- gpio_select_periph_B(GPIO_PIN_PC24, 0); /* RXCK */
-#endif
+ portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
+ portmux_enable_macb1(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
#endif
#if defined(CONFIG_MMC)
- gpio_enable_mmci();
+ portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
#endif
return 0;
return actual_size;
}
-void board_init_info(void)
+int board_early_init_r(void)
{
gd->bd->bi_phy_id[0] = 0x01;
gd->bd->bi_phy_id[1] = 0x03;
+ return 0;
+}
+
+int board_postclk_init(void)
+{
+ /* Use GCLK0 as 10MHz output */
+ gclk_enable_output(0, PORTMUX_DRIVE_LOW);
+ gclk_set_rate(0, GCLK_PARENT_OSC0, 10000000);
+ return 0;
}
/* SPI chip select control */
projects / oweals / u-boot.git / blobdiff