+// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2011
* Logic Product Development <www.logicpd.com>
* Derived from Beagle Board and 3430 SDP code by
* Richard Woodruff <r-woodruff2@ti.com>
* Syed Mohammed Khasim <khasim@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <dm.h>
#include <asm/arch/mem.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
+#include <asm/omap_mmc.h>
#include <asm/mach-types.h>
#include <linux/mtd/rawnand.h>
#include <asm/omap_musb.h>
DECLARE_GLOBAL_DATA_PTR;
-/*
- * two dimensional array of strucures containining board name and Linux
- * machine IDs; row it selected based on CPU column is slected based
- * on hsusb0_data5 pin having a pulldown resistor
- */
-static struct board_id {
- char *name;
- int machine_id;
- char *fdtfile;
-} boards[2][2] = {
- {
- {
- .name = "OMAP35xx SOM LV",
- .machine_id = MACH_TYPE_OMAP3530_LV_SOM,
- .fdtfile = "logicpd-som-lv-35xx-devkit.dtb",
- },
- {
- .name = "OMAP35xx Torpedo",
- .machine_id = MACH_TYPE_OMAP3_TORPEDO,
- .fdtfile = "logicpd-torpedo-35xx-devkit.dtb",
- },
- },
- {
- {
- .name = "DM37xx SOM LV",
- .fdtfile = "logicpd-som-lv-37xx-devkit.dtb",
- },
- {
- .name = "DM37xx Torpedo",
- .fdtfile = "logicpd-torpedo-37xx-devkit.dtb",
- },
- },
+/* This is only needed until SPL gets OF support */
+#ifdef CONFIG_SPL_BUILD
+static const struct ns16550_platdata omap3logic_serial = {
+ .base = OMAP34XX_UART1,
+ .reg_shift = 2,
+ .clock = V_NS16550_CLK,
+ .fcr = UART_FCR_DEFVAL,
+};
+
+U_BOOT_DEVICE(omap3logic_uart) = {
+ "ns16550_serial",
+ &omap3logic_serial
+};
+
+static const struct omap_hsmmc_plat omap3_logic_mmc0_platdata = {
+ .base_addr = (struct hsmmc *)OMAP_HSMMC1_BASE,
+ .cfg.host_caps = MMC_MODE_HS_52MHz | MMC_MODE_HS | MMC_MODE_4BIT,
+ .cfg.f_min = 400000,
+ .cfg.f_max = 52000000,
+ .cfg.voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195,
+ .cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT,
+};
+
+U_BOOT_DEVICE(am335x_mmc0) = {
+ .name = "omap_hsmmc",
+ .platdata = &omap3_logic_mmc0_platdata,
};
+#endif
+
#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
#endif /* CONFIG_USB_EHCI_HCD */
-
/*
* Routine: misc_init_r
* Description: Configure board specific parts
return 0;
}
-/*
- * BOARD_ID_GPIO - GPIO of pin with optional pulldown resistor on SOM LV
- */
-#define BOARD_ID_GPIO 189 /* hsusb0_data5 pin */
-
/*
* Routine: board_init
* Description: Early hardware init.
int board_late_init(void)
{
- struct board_id *board;
- unsigned int val;
-
- /*
- * To identify between a SOM LV and Torpedo module,
- * a pulldown resistor is on hsusb0_data5 for the SOM LV module.
- * Drive the pin (and let it soak), then read it back.
- * If the pin is still high its a Torpedo. If low its a SOM LV
- */
-
- /* Mux hsusb0_data5 as a GPIO */
- MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M4));
-
- if (gpio_request(BOARD_ID_GPIO, "husb0_data5.gpio_189") == 0) {
-
- /*
- * Drive BOARD_ID_GPIO - the pulldown resistor on the SOM LV
- * will drain the voltage.
- */
- gpio_direction_output(BOARD_ID_GPIO, 0);
- gpio_set_value(BOARD_ID_GPIO, 1);
-
- /* Let it soak for a bit */
- sdelay(0x100);
-
- /*
- * Read state of BOARD_ID_GPIO as an input and if its set.
- * If so the board is a Torpedo
- */
- gpio_direction_input(BOARD_ID_GPIO);
- val = gpio_get_value(BOARD_ID_GPIO);
- gpio_free(BOARD_ID_GPIO);
-
- board = &boards[!!(get_cpu_family() == CPU_OMAP36XX)][!!val];
- printf("Board: %s\n", board->name);
-
- /* Set the machine_id passed to Linux */
- if (board->machine_id)
- gd->bd->bi_arch_number = board->machine_id;
-
- /* If the user has not set fdtimage, set the default */
- if (!env_get("fdtimage"))
- env_set("fdtimage", board->fdtfile);
- }
-
- /* restore hsusb0_data5 pin as hsusb0_data5 */
- MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0));
-
#ifdef CONFIG_CMD_NAND_LOCK_UNLOCK
unlock_nand();
#endif
}
#endif
-#if defined(CONFIG_MMC)
-int board_mmc_init(bd_t *bis)
-{
- return omap_mmc_init(0, 0, 0, -1, -1);
-}
-#endif
-
#if defined(CONFIG_MMC)
void board_mmc_power_init(void)
{
return smc911x_initialize(0, CONFIG_SMC911X_BASE);
}
#endif
-
-