#include <common.h>
-#include <asm/arch/mx31.h>
-#include <asm/arch/mx31-regs.h>
+#include <s6e63d6.h>
+#include <netdev.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
DECLARE_GLOBAL_DATA_PTR;
mx31_gpio_mux(MUX_CSPI2_MOSI__I2C2_SCL);
mx31_gpio_mux(MUX_CSPI2_MISO__I2C2_SDA);
- gd->bd->bi_arch_number = 447; /* board id for linux */
- gd->bd->bi_boot_params = (0x80000100); /* adress of boot parameters */
+ gd->bd->bi_arch_number = MACH_TYPE_PCM037; /* board id for linux */
+ gd->bd->bi_boot_params = (0x80000100); /* adress of boot parameters */
return 0;
}
+#ifdef BOARD_LATE_INIT
+int board_late_init(void)
+{
+#ifdef CONFIG_S6E63D6
+ struct s6e63d6 data = {
+ /*
+ * See comment in mxc_spi.c::decode_cs() for .cs field format.
+ * We use GPIO 57 as a chipselect for the S6E63D6 and chipselect
+ * 2 of the SPI controller #1, since it is unused.
+ */
+ .cs = 2 | (57 << 8),
+ .bus = 0,
+ .id = 0,
+ };
+ int ret;
+
+ /* SPI1 */
+ mx31_gpio_mux(MUX_CSPI1_SCLK__CSPI1_CLK);
+ mx31_gpio_mux(MUX_CSPI1_SPI_RDY__CSPI1_DATAREADY_B);
+ mx31_gpio_mux(MUX_CSPI1_MOSI__CSPI1_MOSI);
+ mx31_gpio_mux(MUX_CSPI1_MISO__CSPI1_MISO);
+ mx31_gpio_mux(MUX_CSPI1_SS0__CSPI1_SS0_B);
+ mx31_gpio_mux(MUX_CSPI1_SS1__CSPI1_SS1_B);
+ mx31_gpio_mux(MUX_CSPI1_SS2__CSPI1_SS2_B);
+
+ /* start SPI1 clock */
+ __REG(CCM_CGR2) = __REG(CCM_CGR2) | (3 << 2);
+
+ /* GPIO 57 */
+ /* sw_mux_ctl_key_col4_key_col5_key_col6_key_col7 */
+ mx31_gpio_mux(IOMUX_MODE(0x63, MUX_CTL_GPIO));
+
+ /* SPI1 CS2 is free */
+ ret = s6e63d6_init(&data);
+ if (ret)
+ return ret;
+
+ /*
+ * This is a "magic" sequence to initialise a C0240QGLA / C0283QGLC
+ * OLED display connected to a S6E63D6 SPI display controller in the
+ * 18 bit RGB mode
+ */
+ s6e63d6_index(&data, 2);
+ s6e63d6_param(&data, 0x0182);
+ s6e63d6_index(&data, 3);
+ s6e63d6_param(&data, 0x8130);
+ s6e63d6_index(&data, 0x10);
+ s6e63d6_param(&data, 0x0000);
+ s6e63d6_index(&data, 5);
+ s6e63d6_param(&data, 0x0001);
+ s6e63d6_index(&data, 0x22);
+#endif
+ return 0;
+}
+#endif
+
int checkboard (void)
{
printf("Board: Phytec phyCore i.MX31\n");
return 0;
}
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_SMC911X
+ rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+ return rc;
+}