#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
-#include <asm/errno.h>
+#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
#include <i2c.h>
+#include <pwm.h>
DECLARE_GLOBAL_DATA_PTR;
+#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_HYS)
+
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
int dram_init(void)
{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+ gd->ram_size = imx_ddr_size();
return 0;
}
/* Reset AR8033 PHY */
gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
- udelay(500);
+ mdelay(10);
gpio_set_value(IMX_GPIO_NR(1, 28), 1);
+ mdelay(1);
}
static iomux_v3_cfg_t const usdhc2_pads[] = {
/* set debug port address: SerDes Test and System Mode Control */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
/* enable rgmii tx clock delay */
- phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+ /* set the reserved bits to avoid board specific voltage peak issue*/
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47);
return 0;
}
/* Backlight enable for LVDS display */
MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
+ /* backlight PWM brightness control */
+ MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void do_enable_hdmi(struct display_info_t const *dev)
} } };
size_t display_count = ARRAY_SIZE(displays);
-static void setup_display(void)
+static void enable_videopll(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ s32 timeout = 100000;
+
+ setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
+
+ /* set video pll to 910MHz (24MHz * (37+11/12))
+ * video pll post div to 910/4 = 227.5MHz
+ */
+ clrsetbits_le32(&ccm->analog_pll_video,
+ BM_ANADIG_PLL_VIDEO_DIV_SELECT |
+ BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT,
+ BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) |
+ BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0));
+
+ writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
+ writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
+
+ clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
+
+ while (timeout--)
+ if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+ break;
+
+ if (timeout < 0)
+ printf("Warning: video pll lock timeout!\n");
+
+ clrsetbits_le32(&ccm->analog_pll_video,
+ BM_ANADIG_PLL_VIDEO_BYPASS,
+ BM_ANADIG_PLL_VIDEO_ENABLE);
+}
+
+static void setup_display_b850v3(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- int reg;
- enable_ipu_clock();
+ enable_videopll();
+
+ /* IPU1 D0 clock is 227.5 / 3.5 = 65MHz */
+ clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
+
imx_setup_hdmi();
- reg = readl(&mxc_ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
- writel(reg, &mxc_ccm->CCGR3);
-
- reg = readl(&mxc_ccm->cs2cdr);
- reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
- MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
- reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
- (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
- writel(reg, &mxc_ccm->cs2cdr);
-
- reg = readl(&mxc_ccm->cscmr2);
- reg |= (MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
- writel(reg, &mxc_ccm->cscmr2);
-
- reg = readl(&mxc_ccm->chsccdr);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
- writel(reg, &mxc_ccm->chsccdr);
-
- reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
- | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
- | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
- | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
- | IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT
- | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
- | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
- | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0
- | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
- writel(reg, &iomux->gpr[2]);
-
- reg = readl(&iomux->gpr[3]);
- reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
- IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
- IOMUXC_GPR3_HDMI_MUX_CTL_MASK))
- | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
- << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)
- | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
- << IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET);
- writel(reg, &iomux->gpr[3]);
+ /* Set LDB_DI0 as clock source for IPU_DI0 */
+ clrsetbits_le32(&mxc_ccm->chsccdr,
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
+ (CHSCCDR_CLK_SEL_LDB_DI0 <<
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
+
+ /* Turn on IPU LDB DI0 clocks */
+ setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
+
+ enable_ipu_clock();
+
+ writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
+ IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW |
+ IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
+ IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
+ IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT |
+ IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
+ IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
+ IOMUXC_GPR2_SPLIT_MODE_EN_MASK |
+ IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 |
+ IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0,
+ &iomux->gpr[2]);
+
+ clrbits_le32(&iomux->gpr[3],
+ IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
+ IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
+ IOMUXC_GPR3_HDMI_MUX_CTL_MASK);
+}
+
+static void setup_display_bx50v3(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* When a reset/reboot is performed the display power needs to be turned
+ * off for atleast 500ms. The boot time is ~300ms, we need to wait for
+ * an additional 200ms here. Unfortunately we use external PMIC for
+ * doing the reset, so can not differentiate between POR vs soft reset
+ */
+ mdelay(200);
+
+ /* IPU1 DI0 clock is 480/7 = 68.5 MHz */
+ setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
+
+ /* Set LDB_DI0 as clock source for IPU_DI0 */
+ clrsetbits_le32(&mxc_ccm->chsccdr,
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
+ (CHSCCDR_CLK_SEL_LDB_DI0 <<
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
+
+ /* Turn on IPU LDB DI0 clocks */
+ setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
+
+ enable_ipu_clock();
+
+ writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
+ IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
+ IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
+ IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
+ IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
+ &iomux->gpr[2]);
+
+ clrsetbits_le32(&iomux->gpr[3],
+ IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
+ (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
+ IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
/* backlights off until needed */
imx_iomux_v3_setup_multiple_pads(backlight_pads,
static iomux_v3_cfg_t const misc_pads[] = {
MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL),
+ MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL),
+ MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL),
+ MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL),
+ MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL),
+ MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL),
};
#define SUS_S3_OUT IMX_GPIO_NR(4, 11)
#define WIFI_EN IMX_GPIO_NR(6, 14)
setup_iomux_uart();
-
+#if defined(CONFIG_VIDEO_IPUV3)
+ if (IS_ENABLED(CONFIG_TARGET_GE_B850V3))
+ /* Set LDB clock to Video PLL */
+ select_ldb_di_clock_source(MXC_PLL5_CLK);
+ else
+ /* Set LDB clock to USB PLL */
+ select_ldb_di_clock_source(MXC_PLL3_SW_CLK);
+#endif
return 0;
}
gpio_direction_output(SUS_S3_OUT, 1);
gpio_direction_output(WIFI_EN, 1);
#if defined(CONFIG_VIDEO_IPUV3)
- setup_display();
+ if (IS_ENABLED(CONFIG_TARGET_GE_B850V3))
+ setup_display_b850v3();
+ else
+ setup_display_bx50v3();
#endif
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
};
#endif
+void pmic_init(void)
+{
+#define I2C_PMIC 0x2
+#define DA9063_I2C_ADDR 0x58
+#define DA9063_REG_BCORE2_CFG 0x9D
+#define DA9063_REG_BCORE1_CFG 0x9E
+#define DA9063_REG_BPRO_CFG 0x9F
+#define DA9063_REG_BIO_CFG 0xA0
+#define DA9063_REG_BMEM_CFG 0xA1
+#define DA9063_REG_BPERI_CFG 0xA2
+#define DA9063_BUCK_MODE_MASK 0xC0
+#define DA9063_BUCK_MODE_MANUAL 0x00
+#define DA9063_BUCK_MODE_SLEEP 0x40
+#define DA9063_BUCK_MODE_SYNC 0x80
+#define DA9063_BUCK_MODE_AUTO 0xC0
+
+ uchar val;
+
+ i2c_set_bus_num(I2C_PMIC);
+
+ i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1);
+ val &= ~DA9063_BUCK_MODE_MASK;
+ val |= DA9063_BUCK_MODE_SYNC;
+ i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1);
+
+ i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1);
+ val &= ~DA9063_BUCK_MODE_MASK;
+ val |= DA9063_BUCK_MODE_SYNC;
+ i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1);
+
+ i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1);
+ val &= ~DA9063_BUCK_MODE_MASK;
+ val |= DA9063_BUCK_MODE_SYNC;
+ i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1);
+
+ i2c_read(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1);
+ val &= ~DA9063_BUCK_MODE_MASK;
+ val |= DA9063_BUCK_MODE_SYNC;
+ i2c_write(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1);
+
+ i2c_read(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1);
+ val &= ~DA9063_BUCK_MODE_MASK;
+ val |= DA9063_BUCK_MODE_SYNC;
+ i2c_write(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1);
+
+ i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1);
+ val &= ~DA9063_BUCK_MODE_MASK;
+ val |= DA9063_BUCK_MODE_SYNC;
+ i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1);
+}
+
int board_late_init(void)
{
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
+
+#ifdef CONFIG_VIDEO_IPUV3
/* We need at least 200ms between power on and backlight on
* as per specifications from CHI MEI */
mdelay(250);
+ /* enable backlight PWM 1 */
+ pwm_init(0, 0, 0);
+
+ /* duty cycle 5000000ns, period: 5000000ns */
+ pwm_config(0, 5000000, 5000000);
+
/* Backlight Power */
gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
+ pwm_enable(0);
+#endif
+
+ /* board specific pmic init */
+ pmic_init();
+
return 0;
}
projects / oweals / u-boot.git / blobdiff