*/
#include <common.h>
-#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
-static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
-{
- i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
-}
-
-unsigned int fsl_ddr_get_mem_data_rate(void)
-{
- return get_ddr_freq(0);
-}
-
-void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
- unsigned int ctrl_num)
-{
- unsigned int i;
- unsigned int i2c_address = 0;
-
- for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
- if (ctrl_num == 0 && i == 0)
- i2c_address = SPD_EEPROM_ADDRESS1;
- get_spd(&(ctrl_dimms_spd[i]), i2c_address);
- }
-}
-
-typedef struct {
- u32 datarate_mhz_low;
- u32 datarate_mhz_high;
+struct board_specific_parameters {
u32 n_ranks;
+ u32 datarate_mhz_high;
u32 clk_adjust;
u32 cpo;
u32 write_data_delay;
- u32 force_2T;
-} board_specific_parameters_t;
+ u32 force_2t;
+};
+
-/* ranges for parameters:
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ *
+ * ranges for parameters:
* wr_data_delay = 0-6
* clk adjust = 0-8
* cpo 2-0x1E (30)
*/
-
-
-/* XXX: these values need to be checked for all interleaving modes. */
-/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
- * seem reliable, but errors will appear when memory intensive
- * program is run. */
-/* XXX: Single rank at 800 MHz is OK. */
-const board_specific_parameters_t board_specific_parameters[][20] = {
- {
- /* memory controller 0 */
- /* lo| hi| num| clk| cpo|wrdata|2T */
- /* mhz| mhz|ranks|adjst| | delay| */
- { 0, 333, 2, 6, 7, 3, 0},
- {334, 400, 2, 6, 9, 3, 0},
- {401, 549, 2, 6, 11, 3, 0},
- {550, 680, 2, 1, 10, 5, 0},
- {681, 850, 2, 1, 12, 5, 1},
- { 0, 333, 1, 6, 7, 3, 0},
- {334, 400, 1, 6, 9, 3, 0},
- {401, 549, 1, 6, 11, 3, 0},
- {550, 680, 1, 1, 10, 5, 0},
- {681, 850, 1, 1, 12, 5, 0}
- },
+static const struct board_specific_parameters dimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| clk| cpo|wrdata|2T
+ * ranks| mhz|adjst| | delay|
+ */
+#ifdef CONFIG_SYS_FSL_DDR2
+ {2, 549, 4, 0x1f, 2, 0},
+ {2, 680, 4, 0x1f, 3, 0},
+ {2, 850, 4, 0x1f, 4, 0},
+ {1, 549, 4, 0x1f, 2, 0},
+ {1, 680, 4, 0x1f, 3, 0},
+ {1, 850, 4, 0x1f, 4, 0},
+#else
+ {2, 850, 6, 0x1f, 4, 0},
+ {1, 850, 4, 0x1f, 4, 0},
+#endif
+ {}
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
- const board_specific_parameters_t *pbsp =
- &(board_specific_parameters[ctrl_num][0]);
- u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
- sizeof(board_specific_parameters[0][0]);
- u32 i;
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
+ int i;
+
+ if (ctrl_num) {
+ printf("Wrong parameter for controller number %d", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
- /* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+ /*
+ * set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
* that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
* there are two dimms in the controller, set odt_rd_cfg to 3 and
* odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
*/
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
- if (i&1) { /* odd CS */
- popts->cs_local_opts[i].odt_rd_cfg = 0;
- popts->cs_local_opts[i].odt_wr_cfg = 0;
- } else { /* even CS */
- if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
- popts->cs_local_opts[i].odt_rd_cfg = 0;
- popts->cs_local_opts[i].odt_wr_cfg = 4;
- } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
- popts->cs_local_opts[i].odt_rd_cfg = 3;
- popts->cs_local_opts[i].odt_wr_cfg = 3;
- }
- }
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 1;
}
+ pbsp = dimm0;
+
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
- for (i = 0; i < num_params; i++) {
- if (ddr_freq >= pbsp->datarate_mhz_low &&
- ddr_freq <= pbsp->datarate_mhz_high &&
- pdimm->n_ranks == pbsp->n_ranks) {
- popts->clk_adjust = pbsp->clk_adjust;
- popts->cpo_override = pbsp->cpo;
- popts->write_data_delay = pbsp->write_data_delay;
- popts->twoT_en = pbsp->force_2T;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->twot_en = pbsp->force_2t;
+ goto found;
+ }
+ pbsp_highest = pbsp;
}
pbsp++;
}
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found "
+ "for data rate %lu MT/s!\n"
+ "Trying to use the highest speed (%u) parameters\n",
+ ddr_freq, pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->cpo_override = pbsp_highest->cpo;
+ popts->write_data_delay = pbsp_highest->write_data_delay;
+ popts->twot_en = pbsp_highest->force_2t;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+
+found:
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
+ popts->wrlvl_en = 1;
+ /* Write leveling override */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xa;
+ popts->wrlvl_start = 0x8;
+ /* Rtt and Rtt_WR override */
+ popts->rtt_override = 1;
+ popts->rtt_override_value = DDR3_RTT_120_OHM;
+ popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */
}