#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/spi.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/sys_proto.h>
#include <i2c.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/imx-common/video.h>
+#include <asm/arch/crm_regs.h>
+#include <pca953x.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
+#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
+ PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
+
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+#define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PMIC 1
+
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
}
};
+#ifndef CONFIG_SYS_FLASH_CFI
/*
* I2C3 MLB, Port Expanders (A, B, C), Video ADC, Light Sensor,
* Compass Sensor, Accelerometer, Res Touch
.gp = IMX_GPIO_NR(3, 18)
}
};
+#endif
static iomux_v3_cfg_t const i2c3_pads[] = {
MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_SD2_DAT0__GPIO1_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
+/*Define for building port exp gpio, pin starts from 0*/
+#define PORTEXP_IO_NR(chip, pin) \
+ ((chip << 5) + pin)
+
+/*Get the chip addr from a ioexp gpio*/
+#define PORTEXP_IO_TO_CHIP(gpio_nr) \
+ (gpio_nr >> 5)
+
+/*Get the pin number from a ioexp gpio*/
+#define PORTEXP_IO_TO_PIN(gpio_nr) \
+ (gpio_nr & 0x1f)
+
+static int port_exp_direction_output(unsigned gpio, int value)
+{
+ int ret;
+
+ i2c_set_bus_num(2);
+ ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
+ if (ret)
+ return ret;
+
+ ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
+ (1 << PORTEXP_IO_TO_PIN(gpio)),
+ (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
+
+ if (ret)
+ return ret;
+
+ ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
+ (1 << PORTEXP_IO_TO_PIN(gpio)),
+ (value << PORTEXP_IO_TO_PIN(gpio)));
+
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const eimnor_pads[] = {
+ MX6_PAD_EIM_D16__EIM_DATA16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D17__EIM_DATA17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D18__EIM_DATA18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D19__EIM_DATA19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D20__EIM_DATA20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D21__EIM_DATA21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D22__EIM_DATA22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D23__EIM_DATA23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D24__EIM_DATA24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D25__EIM_DATA25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D26__EIM_DATA26 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D27__EIM_DATA27 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D28__EIM_DATA28 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D29__EIM_DATA29 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D30__EIM_DATA30 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_D31__EIM_DATA31 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA0__EIM_AD00 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA1__EIM_AD01 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA2__EIM_AD02 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA3__EIM_AD03 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA4__EIM_AD04 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA5__EIM_AD05 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA6__EIM_AD06 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA7__EIM_AD07 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA8__EIM_AD08 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA9__EIM_AD09 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA10__EIM_AD10 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA11__EIM_AD11 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL) ,
+ MX6_PAD_EIM_DA12__EIM_AD12 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA13__EIM_AD13 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA14__EIM_AD14 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_DA15__EIM_AD15 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A16__EIM_ADDR16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A17__EIM_ADDR17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A18__EIM_ADDR18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A19__EIM_ADDR19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A20__EIM_ADDR20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A21__EIM_ADDR21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A22__EIM_ADDR22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_A23__EIM_ADDR23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
+ MX6_PAD_EIM_OE__EIM_OE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_EIM_RW__EIM_RW | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_EIM_CS0__EIM_CS0_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void eimnor_cs_setup(void)
+{
+ struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR;
+
+ writel(0x00020181, &weim_regs->cs0gcr1);
+ writel(0x00000001, &weim_regs->cs0gcr2);
+ writel(0x0a020000, &weim_regs->cs0rcr1);
+ writel(0x0000c000, &weim_regs->cs0rcr2);
+ writel(0x0804a240, &weim_regs->cs0wcr1);
+ writel(0x00000120, &weim_regs->wcr);
+
+ set_chipselect_size(CS0_128);
+}
+
+static void setup_iomux_eimnor(void)
+{
+ imx_iomux_v3_setup_multiple_pads(eimnor_pads, ARRAY_SIZE(eimnor_pads));
+
+ gpio_direction_output(IMX_GPIO_NR(5, 4), 0);
+
+ eimnor_cs_setup();
+}
+
static void setup_iomux_enet(void)
{
imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
}
#endif
+#ifdef CONFIG_NAND_MXS
+static iomux_v3_cfg_t gpmi_pads[] = {
+ MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL0),
+ MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+ MX6_PAD_SD4_DAT0__NAND_DQS | MUX_PAD_CTRL(GPMI_PAD_CTRL1),
+};
+
+static void setup_gpmi_nand(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* config gpmi nand iomux */
+ imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+ setup_gpmi_io_clk((MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL(3)));
+
+ /* enable apbh clock gating */
+ setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
int mx6_rgmii_rework(struct phy_device *phydev)
{
unsigned short val;
return 0;
}
-int board_eth_init(bd_t *bis)
+static void setup_fec(void)
{
+ if (is_mx6dqp()) {
+ /*
+ * select ENET MAC0 TX clock from PLL
+ */
+ imx_iomux_set_gpr_register(5, 9, 1, 1);
+ enable_fec_anatop_clock(0, ENET_125MHZ);
+ }
+
setup_iomux_enet();
+}
+
+int board_eth_init(bd_t *bis)
+{
+ setup_fec();
return cpu_eth_init(bis);
}
return (get_cpu_rev() & ~(0xF << 8)) | rev;
}
+#if defined(CONFIG_VIDEO_IPUV3)
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+ imx_enable_hdmi_phy();
+}
+
+struct display_info_t const displays[] = {{
+ .bus = -1,
+ .addr = 0,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = detect_hdmi,
+ .enable = do_enable_hdmi,
+ .mode = {
+ .name = "HDMI",
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15385,
+ .left_margin = 220,
+ .right_margin = 40,
+ .upper_margin = 21,
+ .lower_margin = 7,
+ .hsync_len = 60,
+ .vsync_len = 10,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED,
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+
+ enable_ipu_clock();
+ imx_setup_hdmi();
+
+ reg = readl(&mxc_ccm->chsccdr);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ writel(reg, &mxc_ccm->chsccdr);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+ return 1;
+}
+
int board_early_init_f(void)
{
setup_iomux_uart();
+#ifdef CONFIG_VIDEO_IPUV3
+ setup_display();
+#endif
+
+#ifdef CONFIG_NAND_MXS
+ setup_gpmi_nand();
+#endif
return 0;
}
/* I2C 3 Steer */
gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
imx_iomux_v3_setup_multiple_pads(i2c3_pads, ARRAY_SIZE(i2c3_pads));
+#ifndef CONFIG_SYS_FLASH_CFI
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-
+#endif
gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
imx_iomux_v3_setup_multiple_pads(port_exp, ARRAY_SIZE(port_exp));
+ setup_iomux_eimnor();
return 0;
}
}
#endif
+int power_init_board(void)
+{
+ struct pmic *p;
+ unsigned int value;
+
+ p = pfuze_common_init(I2C_PMIC);
+ if (!p)
+ return -ENODEV;
+
+ if (is_mx6dqp()) {
+ /* set SW2 staby volatage 0.975V*/
+ pmic_reg_read(p, PFUZE100_SW2STBY, &value);
+ value &= ~0x3f;
+ value |= 0x17;
+ pmic_reg_write(p, PFUZE100_SW2STBY, value);
+ }
+
+ return pfuze_mode_init(p, APS_PFM);
+}
+
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
add_board_boot_modes(board_boot_modes);
#endif
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ setenv("board_name", "SABREAUTO");
+
+ if (is_mx6dqp())
+ setenv("board_rev", "MX6QP");
+ else if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
+ setenv("board_rev", "MX6Q");
+ else if (is_cpu_type(MXC_CPU_MX6DL) || is_cpu_type(MXC_CPU_MX6SOLO))
+ setenv("board_rev", "MX6DL");
+#endif
+
return 0;
}
return 0;
}
+
+#ifdef CONFIG_USB_EHCI_MX6
+#define USB_HOST1_PWR PORTEXP_IO_NR(0x32, 7)
+#define USB_OTG_PWR PORTEXP_IO_NR(0x34, 1)
+
+iomux_v3_cfg_t const usb_otg_pads[] = {
+ MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+ switch (port) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+ ARRAY_SIZE(usb_otg_pads));
+
+ /*
+ * Set daisy chain for otg_pin_id on 6q.
+ * For 6dl, this bit is reserved.
+ */
+ imx_iomux_set_gpr_register(1, 13, 1, 0);
+ break;
+ case 1:
+ break;
+ default:
+ printf("MXC USB port %d not yet supported\n", port);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+int board_ehci_power(int port, int on)
+{
+ switch (port) {
+ case 0:
+ if (on)
+ port_exp_direction_output(USB_OTG_PWR, 1);
+ else
+ port_exp_direction_output(USB_OTG_PWR, 0);
+ break;
+ case 1:
+ if (on)
+ port_exp_direction_output(USB_HOST1_PWR, 1);
+ else
+ port_exp_direction_output(USB_HOST1_PWR, 0);
+ break;
+ default:
+ printf("MXC USB port %d not yet supported\n", port);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+#endif
projects / oweals / u-boot.git / blobdiff